component
LT3010EMS8E-5#PBF
Public Made by Adomby adom
Analog Devices Linear Voltage Regulators (LDO), MSOP-8-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3010EMS8E-5#PBF
Analog Devices · Linear Voltage Regulators (LDO) · MSOP-8-EP
LT3010EMS8E-5#PBF from Analog Devices, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output supplies power to the load and requires a minimum 1µF output capacitor to prevent oscillations. |
| 2 | SENSE | input | For the LT3010-5, SENSE is the input to the error amplifier and should connect to OUT, with a 10µA bias current at the nominal rated output voltage. |
| 3 | NC | unconnected | No connection; may be floated, tied to IN or tied to GND. |
| 4 | GND | power_in | Ground; must be connected directly to pin 9 (the exposed backside pad) on the PC board. |
| 5 | SHDN | input | Shutdown input; the output is off when SHDN is pulled low, it can be driven by 5V logic or open-collector logic with a pull-up, and it must be tied to a logic high or VIN if unused. |
| 6 | NC | unconnected | No connection; may be floated, tied to IN or tied to GND. |
| 7 | NC | unconnected | No connection; may be floated, tied to IN or tied to GND. |
| 8 | IN | power_in | Input supplies power to the device; the LT3010 withstands reverse voltages on IN with respect to ground and OUT, and a 1µF to 10µF bypass capacitor is sufficient when required. |
| 9 | GND | power_in | Exposed backside pad is the GND electrical connection and must be soldered to the PCB and connected directly to pin 4. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8-EP |
| Category | Power Management ICs |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage | 4.925 | 5 | 5.075 | V | VIN = 5.5V, ILOAD = 1mA | 3 | |
| Regulated Output Voltage (over temperature) | 4.85 | 5 | 5.15 | V | 6V < VIN < 80V, 1mA < ILOAD < 50mA, l: -40°C to 125°C | 3 | |
| Line Regulation | 3 | 15 | mV | ΔVIN = 5.5V to 80V, ILOAD = 1mA | 3 | ||
| Load Regulation | 25 | 50 | mV | VIN = 6V, ΔILOAD = 1mA to 50mA | 3 | ||
| Load Regulation (over temperature) | 90 | mV | VIN = 6V, ΔILOAD = 1mA to 50mA, l: -40°C to 125°C | 3 | |||
| Dropout Voltage | 100 | 150 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA | 3 | ||
| Dropout Voltage (over temperature) | 190 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA, l: -40°C to 125°C | 3 | |||
| Dropout Voltage | 200 | 260 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA | 3 | ||
| Dropout Voltage (over temperature) | 350 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA, l: -40°C to 125°C | 3 | |||
| Dropout Voltage | 300 | 370 | mV | VIN = VOUT(NOMINAL), ILOAD = 50mA | 3 | ||
| Dropout Voltage (over temperature) | 550 | mV | VIN = VOUT(NOMINAL), ILOAD = 50mA, l: -40°C to 125°C | 3 | |||
| GND Pin Current | 30 | 60 | µA | VIN = VOUT(NOMINAL), ILOAD = 0mA | 3 | ||
| GND Pin Current | 100 | 180 | µA | VIN = VOUT(NOMINAL), ILOAD = 1mA | 3 | ||
| GND Pin Current | 400 | 700 | µA | VIN = VOUT(NOMINAL), ILOAD = 10mA | 3 | ||
| GND Pin Current | 1.8 | 3.3 | mA | VIN = VOUT(NOMINAL), ILOAD = 50mA | 3 | ||
| Input Reverse Leakage Current | 6 | mA | VIN = -80V, VOUT = 0V, l: -40°C to 125°C | 3 | |||
| SHDN Pin Current | 0.5 | 2 | µA | VSHDN = 0V | 3 | ||
| SHDN Pin Current | 0.1 | 0.5 | µA | VSHDN = 6V | 3 | ||
| Quiescent Current in Shutdown | 1 | 5 | µA | VIN = 6V, VSHDN = 0V | 3 | ||
| Current Limit | 60 | mA | LT3010-5 VIN = 6V, ΔVOUT = -0.1V, l: -40°C to 125°C | 3 | |||
| Reverse Output Current | 10 | 20 | µA | LT3010-5 VOUT = 5V, VIN < 5V | 3 | ||
| IN Pin Voltage | -80 | 80 | V | 2 | |||
| OUT Pin Voltage | -60 | 60 | V | 2 | |||
| IN to OUT Differential Voltage | -80 | 80 | V | 2 | |||
| SHDN Pin Input Voltage | -80 | 80 | V | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Operating Junction Temperature Range (LT3010E) | -40 | 125 | °C | LT3010E | 2 | ||
| Lead Temperature | 300 | °C | Soldering, 10 sec | 2 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 40 | °C/W | 2 | |||
| Thermal Resistance Junction-to-Case | θJC | 16 | °C/W | Measured at bottom pad | 2 | ||
| Thermal Resistance Junction-to-Ambient (board range) | θJA | 62 | °C/W | Still air, 3/32" FR-4, 100 sq mm topside copper area | 10 |
CAD (KiCad official)
- Symbol:
LT3010EMS8E-5#PBF - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
lt3010ems8e-5-pbf-etched.step/lt3010ems8e-5-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3010ems8e-5-pbf.step/lt3010ems8e-5-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (18 pp, sha256
c6cfb56a14f03a81, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).