Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LT3008EDC-3.3#TRMPBF
Analog Devices · Linear Voltage Regulators (LDO) · DFN-6-EP(2x2)
LT3008EDC-3.3#TRMPBF from Analog Devices, in a DFN-6-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SENSE/ADJ | input | For the fixed 3.3V version this pin is the error amplifier input (SENSE) and should be connected to OUT at the load for optimum regulation; its bias current is 1μA at nominal output voltage and it may be pulled below ground. |
| 2 | OUT | power_out | Regulator output supplying power to the load; a minimum output capacitor of 2.2μF is required to prevent oscillations. |
| 3 | OUT | power_out | Regulator output supplying power to the load; connect in parallel with pin 2 and provide a minimum 2.2μF output capacitor to prevent oscillations. |
| 4 | IN | power_in | Input supplying power to the device, specified for a 2.0V to 45V input voltage range; a bypass capacitor in the range 0.1μF to 10μF is recommended where the input is far from the main filter. |
| 5 | SHDN | input | Shutdown control; pulling it low turns the output off and puts the device in a low power state, and it must not be left unconnected since the LT3008 does not function if SHDN is floating (tie to IN if unused). |
| 6 | GND | power_in | Ground; connect the bottom of the output-setting resistor divider directly to GND for best regulation. |
| 7 | GND | power_in | Exposed pad of the DFN package, electrically connected to GND; it must be soldered to the PCB and tied directly to pin 6 for optimum performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-6-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage | 2 | 45 | V | 4 | |||
| Regulated Output Voltage LT3008-3.3 | 3.267 | 3.3 | 3.333 | V | VIN = 3.85V, ILOAD = 100μA | 4 | |
| Regulated Output Voltage LT3008-3.3 (full temperature range) | 3.234 | 3.3 | 3.366 | V | 3.85V < VIN < 45V, 1μA < ILOAD < 20mA | 4 | |
| Output Tolerance | -2 | 2 | % | Over Load, Line and Temperature | 1 | ||
| Dropout Voltage ILOAD = 100μA | 115 | 180 | mV | VIN = VOUT(NOMINAL), ILOAD = 100μA | 5 | ||
| Dropout Voltage ILOAD = 100μA (full temperature range) | 250 | mV | VIN = VOUT(NOMINAL), ILOAD = 100μA | 5 | |||
| Dropout Voltage ILOAD = 1mA | 170 | 250 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA | 5 | ||
| Dropout Voltage ILOAD = 1mA (full temperature range) | 350 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA | 5 | |||
| Dropout Voltage ILOAD = 10mA | 270 | 340 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA | 5 | ||
| Dropout Voltage ILOAD = 10mA (full temperature range) | 470 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA | 5 | |||
| Dropout Voltage ILOAD = 20mA | 300 | 365 | mV | VIN = VOUT(NOMINAL), ILOAD = 20mA | 5 | ||
| Dropout Voltage ILOAD = 20mA (full temperature range) | 500 | mV | VIN = VOUT(NOMINAL), ILOAD = 20mA | 5 | |||
| Quiescent Current | 3 | 6 | μA | ILOAD = 0μA | 5 | ||
| GND Pin Current ILOAD = 0μA | 3 | 6 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 0μA | 5 | ||
| GND Pin Current ILOAD = 100μA | 6 | 12 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 100μA | 5 | ||
| GND Pin Current ILOAD = 1mA | 21 | 50 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 1mA | 5 | ||
| GND Pin Current ILOAD = 10mA | 160 | 500 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 10mA | 5 | ||
| GND Pin Current ILOAD = 20mA | 350 | 1200 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 20mA | 5 | ||
| Line Regulation LT3008-3.3 | 3.3 | mV | LT3008-3.3: ΔVIN = 3.85V to 45V, ILOAD = 1mA | 4 | |||
| Line Regulation LT3008-3.3 (full temperature range) | 16.5 | mV | LT3008-3.3: ΔVIN = 3.85V to 45V, ILOAD = 1mA | 4 | |||
| Load Regulation LT3008-3.3 ILOAD = 1μA to 10mA | 2.2 | 11 | mV | VIN = 3.85V, ILOAD = 1μA to 10mA | 5 | ||
| Load Regulation LT3008-3.3 ILOAD = 1μA to 20mA | 2.8 | 28 | mV | VIN = 3.85V, ILOAD = 1μA to 20mA | 5 | ||
| Input Reverse-Leakage Current | 1 | 30 | μA | VIN = -45V, VOUT = 0 | 6 | ||
| Reverse-Output Current | 0.6 | 10 | μA | VOUT = 1.2V, VIN = 0 | 6 | ||
| Ripple Rejection LT3008-3.3 | 47 | 59 | dB | VIN, VOUT = 2V, VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 20mA | 5 | ||
| Thermal Resistance Junction-to-Ambient (DC package) | θJA | 65 | 85 | °C/W | DC package, copper-area range per Table 2 | 2 | |
| Operating Junction Temperature Range (E grade) | TJ | -40 | 125 | °C | E grade | 2 | |
| IN Pin Voltage | VIN | -50 | 50 | V | 2 | ||
| OUT Pin Voltage | VOUT | -50 | 50 | V | 2 | ||
| Input-to-Output Differential Voltage | -50 | 50 | V | 2 | |||
| SENSE Pin Voltage | -50 | 50 | V | 2 | |||
| SHDN Pin Voltage | -50 | 50 | V | Note 8 | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 |
CAD (KiCad official)
- Symbol:
LT3008EDC-3.3#TRMPBF - Footprint:
Package_DFN_QFN:DFN-6-1EP_2x2mm_P0.65mm_EP1x1.6mm - 3D model: DFN-6-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt3008edc-3-3-trmpbf-etched.step/lt3008edc-3-3-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3008edc-3-3-trmpbf.step/lt3008edc-3-3-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
1def3249b43dc637, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).