component
LT1763CS8-1.8#TRPBF
Public Made by Adomby adom
Analog Devices Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SO-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLT1763CS8-1.8#TRPBF
Analog Devices · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SO-8
LT1763CS8-1.8#TRPBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output supplies power to the load and requires a minimum output capacitor of 3.3µF to prevent oscillations. |
| 2 | SENSE | input | For the fixed-voltage LT1763-1.8, SENSE is the error amplifier input and should be connected to OUT for optimum regulation, with a bias current of 10µA at the nominal output voltage. |
| 3 | GND | power_in | Ground pin; connect the bottom of the output voltage setting divider directly to the GND pins for optimum load regulation. |
| 4 | BYP | passive | Bypass pin clamped internally to ±0.6V; a capacitor of up to 0.01µF from the output reduces output noise to a typical 20µVRMS over 10Hz to 100kHz, and the pin must be left unconnected if not used. |
| 5 | SHDN | input | Shutdown pin; the output is off when SHDN is pulled low, it can be driven by 5V logic or open-collector logic with a pull-up resistor, and it must be connected to VIN if unused. |
| 6 | GND | power_in | Ground pin, one of the GND pins (3, 6, 7) on the SO-8 package. |
| 7 | GND | power_in | Ground pin, one of the GND pins (3, 6, 7) on the SO-8 package. |
| 8 | IN | power_in | Input supply pin; a bypass capacitor of 1µF to 10µF is sufficient, and the IN pin voltage is rated ±20V absolute maximum. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage (25°C, VIN = 2.3V, ILOAD = 1mA) | VOUT | 1.782 | 1.8 | 1.818 | V | VIN = 2.3V, ILOAD = 1mA | 4 |
| Regulated Output Voltage (full temperature range) | VOUT | 1.755 | 1.8 | 1.845 | V | 2.8V < VIN < 20V, 1mA < ILOAD < 500mA (l: full operating temperature range) | 4 |
| Load Regulation | 4 | 9 | mV | VIN = 2.8V, ∆ILOAD = 1mA to 500mA | 4 | ||
| Load Regulation (full temperature range) | 18 | mV | VIN = 2.8V, ∆ILOAD = 1mA to 500mA (l: full operating temperature range) | 4 | |||
| Line Regulation (full temperature range) | 1 | 5 | mV | ∆VIN = 2.3V to 20V, ILOAD = 1mA (l: full operating temperature range) | 4 | ||
| Minimum Operating Voltage (C, I grade) | 1.8 | 2.3 | V | ILOAD = 500mA (Notes 3, 11) | 4 | ||
| Dropout Voltage (25°C) | 0.13 | 0.19 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA | 4 | ||
| Dropout Voltage (full temperature range) | 0.25 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA (l: full operating temperature range) | 4 | |||
| Dropout Voltage (25°C) | 0.17 | 0.22 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA | 4 | ||
| Dropout Voltage (full temperature range) | 0.32 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA (l: full operating temperature range) | 4 | |||
| Dropout Voltage (25°C) | 0.2 | 0.24 | V | VIN = VOUT(NOMINAL), ILOAD = 100mA | 4 | ||
| Dropout Voltage (full temperature range) | 0.34 | V | VIN = VOUT(NOMINAL), ILOAD = 100mA (l: full operating temperature range) | 4 | |||
| Dropout Voltage (25°C) | 0.3 | 0.35 | V | VIN = VOUT(NOMINAL), ILOAD = 500mA | 4 | ||
| Dropout Voltage (full temperature range) | 0.45 | V | VIN = VOUT(NOMINAL), ILOAD = 500mA (l: full operating temperature range) | 4 | |||
| GND Pin Current (full temperature range) | 30 | 75 | µA | VIN = VOUT(NOMINAL), ILOAD = 0mA (Notes 5, 7) | 5 | ||
| GND Pin Current (full temperature range) | 65 | 120 | µA | VIN = VOUT(NOMINAL), ILOAD = 1mA (Notes 5, 7) | 5 | ||
| GND Pin Current (full temperature range) | 1.1 | 1.6 | mA | VIN = VOUT(NOMINAL), ILOAD = 50mA (Notes 5, 7) | 5 | ||
| GND Pin Current (full temperature range) | 2 | 3 | mA | VIN = VOUT(NOMINAL), ILOAD = 100mA (Notes 5, 7) | 5 | ||
| GND Pin Current (full temperature range) | 5 | 8 | mA | VIN = VOUT(NOMINAL), ILOAD = 250mA (Notes 5, 7) | 5 | ||
| GND Pin Current (full temperature range) | 11 | 16 | mA | VIN = VOUT(NOMINAL), ILOAD = 500mA (Notes 5, 7) | 5 | ||
| Shutdown Threshold (full temperature range) | 0.25 | 0.8 | V | VOUT = Off to On (l) | 5 | ||
| Shutdown Threshold (full temperature range) | 0.65 | 2 | V | VOUT = On to Off (l) | 5 | ||
| Quiescent Current in Shutdown | 0.1 | 1 | µA | VIN = 6V, VSHDN = 0V | 5 | ||
| Ripple Rejection | 50 | 65 | dB | VIN, VOUT = 1.5V (Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 500mA | 5 | ||
| Current Limit (C, I grade) | 520 | mA | C, I Grade: VIN = VOUT(NOMINAL) + 1V or 2.3V (Note 12), ∆VOUT = -0.1V (l) | 5 | |||
| Input Reverse Leakage Current (full temperature range) | 1 | mA | VIN = -20V, VOUT = 0V (l) | 5 | |||
| Reverse Output Current (LT1763-1.8) | 10 | 20 | µA | VOUT = 1.8V, VIN < 1.8V | 5 | ||
| SHDN Pin Current | 0.1 | µA | VSHDN = 0V (Note 9) | 5 | |||
| SHDN Pin Current | 1 | µA | VSHDN = 20V (Note 9) | 5 | |||
| Output Voltage Noise | 20 | µVRMS | COUT = 10µF, CBYP = 0.01µF, ILOAD = 500mA, BW = 10Hz to 100kHz | 5 | |||
| Input pin voltage (IN) | -20 | 20 | V | 2 | |||
| OUT pin voltage | -20 | 20 | V | 2 | |||
| Input to output differential voltage | -20 | 20 | V | 2 | |||
| SENSE pin voltage | -20 | 20 | V | Fixed-voltage versions (SENSE pin) | 2 | ||
| SHDN pin voltage | -20 | 20 | V | 2 | |||
| BYP pin voltage | -0.6 | 0.6 | V | 2 | |||
| Operating Junction Temperature Range (C grade) | TJ | -40 | 125 | °C | C, I Grade (Note 2) | 2 | |
| Storage Temperature Range (S8 package) | TSTG | -65 | 150 | °C | S8 package | 2 | |
| Lead Temperature (Soldering, 10 sec, S8 package) | 300 | °C | S8 package, soldering 10 sec | 2 | |||
| Maximum Junction Temperature (S8 package) | TJMAX | 150 | °C | S8 package | 2 | ||
| Thermal Resistance Junction-to-Ambient (S8 package) | θJA | 70 | °C/W | S8 package | 2 | ||
| Thermal Resistance Junction-to-Case (S8 package) | θJC | 35 | °C/W | S8 package | 2 | ||
| Thermal Resistance Junction-to-Ambient (SO-8, copper area 2500mm2) | θJA | 60 | °C/W | SO-8, 2500mm2 topside copper, 2500mm2 board area, 3/32" FR-4 still air | 17 | ||
| Thermal Resistance Junction-to-Ambient (SO-8, copper area 50mm2) | θJA | 86 | °C/W | SO-8, 50mm2 topside copper, 2500mm2 board area, 3/32" FR-4 still air | 17 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | COPPER | Table 1. DE Package, 12-Lead DFN COPPER AREA | 16 |
CAD (KiCad official)
- Symbol:
LT1763CS8-1.8#TRPBF - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lt1763cs8-1-8-trpbf-etched.step/lt1763cs8-1-8-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1763cs8-1-8-trpbf.step/lt1763cs8-1-8-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
2bc1aa72821928b4, retrieved 2026-10-21, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).