main
Ray
Publish 0.1.0
a81213b
LT1762EMS8#TRPBF
Analog Devices · Linear Voltage Regulators (LDO) · MSOP-8
LT1762EMS8#TRPBF from Analog Devices, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output supplies power to the load, and a minimum output capacitor of 2.2µF is required to prevent oscillations. |
| 2 | SENSE/ADJ | input | For the adjustable LT1762 this is the ADJ error-amplifier input, clamped to ±7V with a 30nA bias current, setting the output from 1.22V to 20V; for fixed versions it is the SENSE input, best connected to OUT for optimum regulation. |
| 3 | BYP | passive | Bypass pin clamped internally to ±0.6V; a maximum 0.01µF capacitor from the output reduces noise to a typical 20µVRMS over 10Hz to 100kHz, and it must be left unconnected if not used. |
| 4 | GND | power_in | Ground reference pin for the regulator. |
| 5 | SHDN | input | Shutdown input that turns the output off when pulled low, can be driven by 5V logic or open-collector logic with a pull-up resistor, and must be connected to VIN if unused. |
| 6 | NC | unconnected | No connection. |
| 7 | NC | unconnected | No connection. |
| 8 | IN | power_in | Input supply pin for the regulator, which is reverse-battery protected and should have a 1µF to 10µF bypass capacitor when more than six inches from the main input filter capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage (ADJ pin, VIN = 2V, ILOAD = 1mA) | 1.208 | 1.22 | 1.232 | V | VIN = 2V, ILOAD = 1mA | 3 | |
| ADJ Pin Voltage (Regulated Output Voltage, l) | 1.19 | 1.22 | 1.25 | V | 2.22V < VIN < 20V, 1mA < ILOAD < 150mA, l = full operating temperature range | 3 | |
| Line Regulation (LT1762 adjustable) | 1 | 5 | mV | ΔVIN = 2V to 20V, ILOAD = 1mA, l | 3 | ||
| Load Regulation (LT1762 adjustable) | 1 | 6 | mV | VIN = 2.22V, ΔILOAD = 1mA to 150mA | 3 | ||
| Load Regulation (LT1762 adjustable, l) | 15 | mV | VIN = 2.22V, ΔILOAD = 1mA to 150mA, l = full operating temperature range | 3 | |||
| Minimum Operating Voltage | 1.8 | 2.3 | V | ILOAD = 150mA, l | 3 | ||
| Dropout Voltage | 0.09 | 0.15 | V | VIN = VOUT(NOMINAL), ILOAD = 1mA | 3 | ||
| Dropout Voltage | 0.19 | V | VIN = VOUT(NOMINAL), ILOAD = 1mA, l | 3 | |||
| Dropout Voltage | 0.15 | 0.21 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA | 3 | ||
| Dropout Voltage | 0.25 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA, l | 3 | |||
| Dropout Voltage | 0.21 | 0.27 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA | 3 | ||
| Dropout Voltage | 0.31 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA, l | 3 | |||
| Dropout Voltage | 0.27 | 0.33 | V | VIN = VOUT(NOMINAL), ILOAD = 150mA | 3 | ||
| Dropout Voltage | 0.4 | V | VIN = VOUT(NOMINAL), ILOAD = 150mA, l | 3 | |||
| GND Pin Current | 25 | 65 | µA | VIN = VOUT(NOMINAL), ILOAD = 0mA, l | 3 | ||
| GND Pin Current | 70 | 120 | µA | VIN = VOUT(NOMINAL), ILOAD = 1mA, l | 3 | ||
| GND Pin Current | 350 | 500 | µA | VIN = VOUT(NOMINAL), ILOAD = 10mA, l | 3 | ||
| GND Pin Current | 1.3 | 1.8 | mA | VIN = VOUT(NOMINAL), ILOAD = 50mA, l | 3 | ||
| GND Pin Current | 4 | 7 | mA | VIN = VOUT(NOMINAL), ILOAD = 150mA, l | 3 | ||
| Current Limit (l) | 160 | mA | VIN = VOUT(NOMINAL) + 1V, ΔVOUT = -0.1V, l | 4 | |||
| Current Limit | 400 | mA | VIN = 7V, VOUT = 0V | 4 | |||
| ADJ Pin Bias Current | IADJ | 30 | 100 | nA | Notes 3, 8 | 4 | |
| Shutdown Threshold (VOUT Off to On, l) | 0.8 | 2 | V | VOUT = Off to On, l | 4 | ||
| Shutdown Threshold (VOUT On to Off, l) | 0.25 | 0.65 | V | VOUT = On to Off, l | 4 | ||
| Quiescent Current in Shutdown | 0.1 | 1 | µA | VIN = 6V, VSHDN = 0V | 4 | ||
| Ripple Rejection | 50 | 65 | dB | VIN, VOUT = 1V (Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 150mA | 4 | ||
| Input Reverse Leakage Current | 1 | mA | VIN = -20V, VOUT = 0V, l | 4 | |||
| Reverse Output Current (LT1762 adjustable) | 5 | 10 | µA | VOUT = 1.22V, VIN < 1.22V (Note 3) | 4 | ||
| Output Voltage Noise | 20 | µVRMS | COUT = 10µF, CBYP = 0.01µF, ILOAD = 150mA, BW = 10Hz to 100kHz | 4 | |||
| SHDN Pin Current | 0.1 | µA | VSHDN = 0V | 4 | |||
| SHDN Pin Current | 1 | µA | VSHDN = 20V | 4 | |||
| IN Pin Voltage | -20 | 20 | V | 2 | |||
| OUT Pin Voltage | -20 | 20 | V | 2 | |||
| Input to Output Differential Voltage | -20 | 20 | V | 2 | |||
| SENSE Pin Voltage | -20 | 20 | V | 2 | |||
| ADJ Pin Voltage | -7 | 7 | V | 2 | |||
| BYP Pin Voltage | -0.6 | 0.6 | V | 2 | |||
| SHDN Pin Voltage | -20 | 20 | V | 2 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Note 2 | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction-to-Ambient Thermal Resistance (MS8) | θJA | 125 | °C/W | MS8 package, as printed in pin configuration | 2 | ||
| Junction-to-Ambient Thermal Resistance (measured range) | θJA | 110 | 140 | °C/W | Measured on 3/32" FR-4, 1 oz copper, still air; varies with copper area (Table 1) | 14 | |
| Maximum Junction Temperature | TJMAX | 150 | °C | Printed in pin configuration header | 2 |
CAD (KiCad official)
- Symbol:
LT1762EMS8#TRPBF - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
lt1762ems8-trpbf-etched.step/lt1762ems8-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1762ems8-trpbf.step/lt1762ems8-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (18 pp, sha256
74e2ca01c993d790, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT1762EMS8#TRPBF
**Analog Devices** · Linear Voltage Regulators (LDO) · MSOP-8
LT1762EMS8#TRPBF from Analog Devices, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output supplies power to the load, and a minimum output capacitor of 2.2µF is required to prevent oscillations. |
| 2 | SENSE/ADJ | input | For the adjustable LT1762 this is the ADJ error-amplifier input, clamped to ±7V with a 30nA bias current, setting the output from 1.22V to 20V; for fixed versions it is the SENSE input, best connected to OUT for optimum regulation. |
| 3 | BYP | passive | Bypass pin clamped internally to ±0.6V; a maximum 0.01µF capacitor from the output reduces noise to a typical 20µVRMS over 10Hz to 100kHz, and it must be left unconnected if not used. |
| 4 | GND | power_in | Ground reference pin for the regulator. |
| 5 | SHDN | input | Shutdown input that turns the output off when pulled low, can be driven by 5V logic or open-collector logic with a pull-up resistor, and must be connected to VIN if unused. |
| 6 | NC | unconnected | No connection. |
| 7 | NC | unconnected | No connection. |
| 8 | IN | power_in | Input supply pin for the regulator, which is reverse-battery protected and should have a 1µF to 10µF bypass capacitor when more than six inches from the main input filter capacitor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage (ADJ pin, VIN = 2V, ILOAD = 1mA) | | 1.208 | 1.22 | 1.232 | V | VIN = 2V, ILOAD = 1mA | 3 |
| ADJ Pin Voltage (Regulated Output Voltage, l) | | 1.19 | 1.22 | 1.25 | V | 2.22V < VIN < 20V, 1mA < ILOAD < 150mA, l = full operating temperature range | 3 |
| Line Regulation (LT1762 adjustable) | | | 1 | 5 | mV | ΔVIN = 2V to 20V, ILOAD = 1mA, l | 3 |
| Load Regulation (LT1762 adjustable) | | | 1 | 6 | mV | VIN = 2.22V, ΔILOAD = 1mA to 150mA | 3 |
| Load Regulation (LT1762 adjustable, l) | | | | 15 | mV | VIN = 2.22V, ΔILOAD = 1mA to 150mA, l = full operating temperature range | 3 |
| Minimum Operating Voltage | | | 1.8 | 2.3 | V | ILOAD = 150mA, l | 3 |
| Dropout Voltage | | | 0.09 | 0.15 | V | VIN = VOUT(NOMINAL), ILOAD = 1mA | 3 |
| Dropout Voltage | | | | 0.19 | V | VIN = VOUT(NOMINAL), ILOAD = 1mA, l | 3 |
| Dropout Voltage | | | 0.15 | 0.21 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA | 3 |
| Dropout Voltage | | | | 0.25 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA, l | 3 |
| Dropout Voltage | | | 0.21 | 0.27 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA | 3 |
| Dropout Voltage | | | | 0.31 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA, l | 3 |
| Dropout Voltage | | | 0.27 | 0.33 | V | VIN = VOUT(NOMINAL), ILOAD = 150mA | 3 |
| Dropout Voltage | | | | 0.4 | V | VIN = VOUT(NOMINAL), ILOAD = 150mA, l | 3 |
| GND Pin Current | | | 25 | 65 | µA | VIN = VOUT(NOMINAL), ILOAD = 0mA, l | 3 |
| GND Pin Current | | | 70 | 120 | µA | VIN = VOUT(NOMINAL), ILOAD = 1mA, l | 3 |
| GND Pin Current | | | 350 | 500 | µA | VIN = VOUT(NOMINAL), ILOAD = 10mA, l | 3 |
| GND Pin Current | | | 1.3 | 1.8 | mA | VIN = VOUT(NOMINAL), ILOAD = 50mA, l | 3 |
| GND Pin Current | | | 4 | 7 | mA | VIN = VOUT(NOMINAL), ILOAD = 150mA, l | 3 |
| Current Limit (l) | | 160 | | | mA | VIN = VOUT(NOMINAL) + 1V, ΔVOUT = -0.1V, l | 4 |
| Current Limit | | | 400 | | mA | VIN = 7V, VOUT = 0V | 4 |
| ADJ Pin Bias Current | IADJ | | 30 | 100 | nA | Notes 3, 8 | 4 |
| Shutdown Threshold (VOUT Off to On, l) | | | 0.8 | 2 | V | VOUT = Off to On, l | 4 |
| Shutdown Threshold (VOUT On to Off, l) | | | 0.25 | 0.65 | V | VOUT = On to Off, l | 4 |
| Quiescent Current in Shutdown | | | 0.1 | 1 | µA | VIN = 6V, VSHDN = 0V | 4 |
| Ripple Rejection | | | 50 | 65 | dB | VIN, VOUT = 1V (Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 150mA | 4 |
| Input Reverse Leakage Current | | | | 1 | mA | VIN = -20V, VOUT = 0V, l | 4 |
| Reverse Output Current (LT1762 adjustable) | | | 5 | 10 | µA | VOUT = 1.22V, VIN < 1.22V (Note 3) | 4 |
| Output Voltage Noise | | | 20 | | µVRMS | COUT = 10µF, CBYP = 0.01µF, ILOAD = 150mA, BW = 10Hz to 100kHz | 4 |
| SHDN Pin Current | | | 0.1 | | µA | VSHDN = 0V | 4 |
| SHDN Pin Current | | | 1 | | µA | VSHDN = 20V | 4 |
| IN Pin Voltage | | -20 | | 20 | V | | 2 |
| OUT Pin Voltage | | -20 | | 20 | V | | 2 |
| Input to Output Differential Voltage | | -20 | | 20 | V | | 2 |
| SENSE Pin Voltage | | -20 | | 20 | V | | 2 |
| ADJ Pin Voltage | | -7 | | 7 | V | | 2 |
| BYP Pin Voltage | | -0.6 | | 0.6 | V | | 2 |
| SHDN Pin Voltage | | -20 | | 20 | V | | 2 |
| Operating Junction Temperature Range | TJ | -40 | | 125 | °C | Note 2 | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Junction-to-Ambient Thermal Resistance (MS8) | θJA | | 125 | | °C/W | MS8 package, as printed in pin configuration | 2 |
| Junction-to-Ambient Thermal Resistance (measured range) | θJA | 110 | | 140 | °C/W | Measured on 3/32" FR-4, 1 oz copper, still air; varies with copper area (Table 1) | 14 |
| Maximum Junction Temperature | TJMAX | | | 150 | °C | Printed in pin configuration header | 2 |
## CAD (KiCad official)
- Symbol: `LT1762EMS8#TRPBF`
- Footprint: `Package_SO:MSOP-8_3x3mm_P0.65mm`
- 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files: `lt1762ems8-trpbf-etched.step` / `lt1762ems8-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt1762ems8-trpbf.step` / `lt1762ems8-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LT1762.pdf) (18 pp, sha256 `74e2ca01c993d790`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt1762ems8-trpbf-datasheet.pdf)