main
Ray
Publish 0.1.0
dab0a7e
LT1377IS8#PBF
Analog Devices · DC-DC Converters · SO-8
LT1377IS8#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VC | passive | Compensation pin, the error amplifier output and current comparator input used for frequency compensation, current limiting and soft start; switch duty cycle goes to zero if pulled below the control pin threshold. |
| 2 | FB | input | Positive output feedback pin, the inverting error amplifier input referenced to a 1.245V internal reference; load on FB should not exceed 250µA when the NFB pin is used. |
| 3 | NFB | input | Negative output feedback pin that regulates at -2.49V through a 100k source resistor and is left open for positive output applications. |
| 4 | S/S | input | Logic-level shutdown and synchronization pin, active low with a typical 1.3V shutdown threshold, synchronizable at 600kHz to 800kHz (LT1372) or 1.2MHz to 1.6MHz (LT1377). |
| 5 | VIN | power_in | Input supply pin to be bypassed with 10µF or more, entering undervoltage lockout when VIN drops below 2.5V. |
| 6 | GND S | power_in | Ground sense pin, a clean ground to which the internal reference, error amplifier and negative feedback amplifier are referred, and which should be connected to ground. |
| 7 | GND | power_in | Ground pin, the emitter connection of the power switch carrying large currents, to be connected directly to a good quality ground plane. |
| 8 | VSW | output | Switch pin, the collector of the power switch carrying large currents, which should have traces to the switching components kept as short as possible. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reference Voltage | VREF | 1.23 | 1.245 | 1.26 | V | Measured at Feedback Pin | 2 |
| Reference Voltage over temperature | VREF | 1.225 | 1.245 | 1.265 | V | VC = 0.8V | 2 |
| Negative Feedback Reference Voltage | VNFB | -2.54 | -2.49 | -2.44 | V | Measured at Negative Feedback Pin | 2 |
| Negative Feedback Reference Voltage, feedback pin open | VNFB | -2.57 | -2.49 | -2.41 | V | Feedback Pin Open, VC = 0.8V | 2 |
| Negative Feedback Input Current | INFB | -45 | -30 | -15 | µA | VNFB = VNFR | 2 |
| Error Amplifier Source Current | 120 | 200 | 350 | µA | VFB = VREF, 150mV, VC = 1.5V | 2 | |
| Error Amplifier Clamp Voltage High Clamp | 1.7 | 1.95 | 2.3 | V | High Clamp, VFB = 1V | 2 | |
| Error Amplifier Clamp Voltage Low Clamp | 0.25 | 0.4 | 0.52 | V | Low Clamp, VFB = 1.5V | 2 | |
| VC Pin Threshold | 0.8 | 1 | 1.25 | V | Duty Cycle = 0% | 2 | |
| Switching Frequency LT1377 | f | 0.9 | 1 | 1.1 | MHz | 2.7V ≤ VIN ≤ 25V | 2 |
| Switching Frequency LT1377 over 0°C to 125°C | f | 0.86 | 1 | 1.16 | MHz | 0°C ≤ TJ ≤ 125°C | 2 |
| Switching Frequency LT1377 I grade | f | 0.8 | 1.16 | MHz | -40°C ≤ TJ < 0°C (I Grade) | 2 | |
| Switch Breakdown Voltage LT1377 | BV | 35 | 47 | V | LT1372/LT1377 | 3 | |
| Switch On Resistance | VSAT | 0.5 | 0.8 | Ω | ISW = 1A | 3 | |
| Switch Current Limit at 50% duty cycle | ILIM | 1.5 | 1.9 | 2.7 | A | Duty Cycle = 50% | 3 |
| Switch Current Limit at 80% duty cycle | ILIM | 1.3 | 1.7 | 2.5 | A | Duty Cycle = 80% (Note 2) | 3 |
| Supply Current Increase During Switch On-Time | ∆IIN | 15 | 25 | mA/A | 3 | ||
| Control Voltage to Switch Current Transconductance | ∆ISW | 2 | A/V | 3 | |||
| Minimum Input Voltage | 2.4 | 2.7 | V | 3 | |||
| Supply Current | IQ | 4 | 5.5 | mA | 2.7V ≤ VIN ≤ 25V | 3 | |
| Shutdown Supply Current | 12 | 30 | µA | 2.7V ≤ VIN ≤ 25V, VS/S ≤ 0.6V, 0°C ≤ TJ ≤ 125°C | 3 | ||
| Shutdown Supply Current I grade | 50 | µA | 2.7V ≤ VIN ≤ 25V, VS/S ≤ 0.6V, -40°C ≤ TJ < 0°C (I Grade) | 3 | |||
| Shutdown Threshold | 0.6 | 1.3 | 2 | V | 2.7V ≤ VIN ≤ 25V | 3 | |
| Shutdown Delay | 5 | 12 | 25 | µs | 3 | ||
| S/S Pin Input Current | -10 | 15 | µA | 0V ≤ VS/S ≤ 5V | 3 | ||
| Synchronization Frequency Range LT1377 | 1.2 | 1.6 | MHz | 3 | |||
| Maximum Switch Duty Cycle | 85 | 95 | % | 3 | |||
| Switch Current Limit Blanking Time | 130 | 260 | ns | 3 | |||
| Error Amplifier Transconductance | gm | 1100 | 1500 | 1900 | µmho | ∆IC = ±25µA | 2 |
| Error Amplifier Transconductance over full temperature range | gm | 700 | 2300 | µmho | 2 | ||
| Error Amplifier Sink Current | 1400 | 2400 | µA | VFB = VREF + 150mV, VC = 1.5V | 2 | ||
| Feedback Input Current | IFB | 250 | 550 | nA | VFB = VREF | 2 | |
| Feedback Input Current over full temperature range | IFB | 900 | nA | 2 | |||
| Reference Voltage Line Regulation | 0.01 | 0.03 | %/V | 2.7V ≤ VIN ≤ 25V, VC = 0.8V | 2 | ||
| Negative Feedback Reference Voltage Line Regulation | 0.01 | 0.05 | %/V | 2.7V ≤ VIN ≤ 25V, VC = 0.8V | 2 | ||
| Operating Junction Temperature Range Industrial | TJ | -40 | 125 | °C | I grade | 2 | |
| Supply Voltage | 30 | V | 2 | ||||
| Switch Voltage LT1377 | 35 | V | LT1372/LT1377 | 2 | |||
| S/S Pin Voltage | 30 | V | 2 | ||||
| Feedback Pin Voltage transient | -10 | 10 | V | Transient, 10ms | 2 | ||
| Feedback Pin Current | 10 | mA | 2 | ||||
| Negative Feedback Pin Voltage transient | -10 | 10 | V | Transient, 10ms | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature | 300 | °C | Soldering, 10 sec | 2 | |||
| Thermal Resistance Junction to Ambient S8 | θJA | 120 | °C/W | S8 package | 2 |
CAD (KiCad official)
- Symbol:
LT1377IS8#PBF - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lt1377is8-pbf-etched.step/lt1377is8-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1377is8-pbf.step/lt1377is8-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (12 pp, sha256
cfd807e8c927796b, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT1377IS8#PBF
**Analog Devices** · DC-DC Converters · SO-8
LT1377IS8#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VC | passive | Compensation pin, the error amplifier output and current comparator input used for frequency compensation, current limiting and soft start; switch duty cycle goes to zero if pulled below the control pin threshold. |
| 2 | FB | input | Positive output feedback pin, the inverting error amplifier input referenced to a 1.245V internal reference; load on FB should not exceed 250µA when the NFB pin is used. |
| 3 | NFB | input | Negative output feedback pin that regulates at -2.49V through a 100k source resistor and is left open for positive output applications. |
| 4 | S/S | input | Logic-level shutdown and synchronization pin, active low with a typical 1.3V shutdown threshold, synchronizable at 600kHz to 800kHz (LT1372) or 1.2MHz to 1.6MHz (LT1377). |
| 5 | VIN | power_in | Input supply pin to be bypassed with 10µF or more, entering undervoltage lockout when VIN drops below 2.5V. |
| 6 | GND S | power_in | Ground sense pin, a clean ground to which the internal reference, error amplifier and negative feedback amplifier are referred, and which should be connected to ground. |
| 7 | GND | power_in | Ground pin, the emitter connection of the power switch carrying large currents, to be connected directly to a good quality ground plane. |
| 8 | VSW | output | Switch pin, the collector of the power switch carrying large currents, which should have traces to the switching components kept as short as possible. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reference Voltage | VREF | 1.23 | 1.245 | 1.26 | V | Measured at Feedback Pin | 2 |
| Reference Voltage over temperature | VREF | 1.225 | 1.245 | 1.265 | V | VC = 0.8V | 2 |
| Negative Feedback Reference Voltage | VNFB | -2.54 | -2.49 | -2.44 | V | Measured at Negative Feedback Pin | 2 |
| Negative Feedback Reference Voltage, feedback pin open | VNFB | -2.57 | -2.49 | -2.41 | V | Feedback Pin Open, VC = 0.8V | 2 |
| Negative Feedback Input Current | INFB | -45 | -30 | -15 | µA | VNFB = VNFR | 2 |
| Error Amplifier Source Current | | 120 | 200 | 350 | µA | VFB = VREF, 150mV, VC = 1.5V | 2 |
| Error Amplifier Clamp Voltage High Clamp | | 1.7 | 1.95 | 2.3 | V | High Clamp, VFB = 1V | 2 |
| Error Amplifier Clamp Voltage Low Clamp | | 0.25 | 0.4 | 0.52 | V | Low Clamp, VFB = 1.5V | 2 |
| VC Pin Threshold | | 0.8 | 1 | 1.25 | V | Duty Cycle = 0% | 2 |
| Switching Frequency LT1377 | f | 0.9 | 1 | 1.1 | MHz | 2.7V ≤ VIN ≤ 25V | 2 |
| Switching Frequency LT1377 over 0°C to 125°C | f | 0.86 | 1 | 1.16 | MHz | 0°C ≤ TJ ≤ 125°C | 2 |
| Switching Frequency LT1377 I grade | f | 0.8 | | 1.16 | MHz | -40°C ≤ TJ < 0°C (I Grade) | 2 |
| Switch Breakdown Voltage LT1377 | BV | | 35 | 47 | V | LT1372/LT1377 | 3 |
| Switch On Resistance | VSAT | | 0.5 | 0.8 | Ω | ISW = 1A | 3 |
| Switch Current Limit at 50% duty cycle | ILIM | 1.5 | 1.9 | 2.7 | A | Duty Cycle = 50% | 3 |
| Switch Current Limit at 80% duty cycle | ILIM | 1.3 | 1.7 | 2.5 | A | Duty Cycle = 80% (Note 2) | 3 |
| Supply Current Increase During Switch On-Time | ∆IIN | | 15 | 25 | mA/A | | 3 |
| Control Voltage to Switch Current Transconductance | ∆ISW | | 2 | | A/V | | 3 |
| Minimum Input Voltage | | | 2.4 | 2.7 | V | | 3 |
| Supply Current | IQ | | 4 | 5.5 | mA | 2.7V ≤ VIN ≤ 25V | 3 |
| Shutdown Supply Current | | | 12 | 30 | µA | 2.7V ≤ VIN ≤ 25V, VS/S ≤ 0.6V, 0°C ≤ TJ ≤ 125°C | 3 |
| Shutdown Supply Current I grade | | | | 50 | µA | 2.7V ≤ VIN ≤ 25V, VS/S ≤ 0.6V, -40°C ≤ TJ < 0°C (I Grade) | 3 |
| Shutdown Threshold | | 0.6 | 1.3 | 2 | V | 2.7V ≤ VIN ≤ 25V | 3 |
| Shutdown Delay | | 5 | 12 | 25 | µs | | 3 |
| S/S Pin Input Current | | | -10 | 15 | µA | 0V ≤ VS/S ≤ 5V | 3 |
| Synchronization Frequency Range LT1377 | | | 1.2 | 1.6 | MHz | | 3 |
| Maximum Switch Duty Cycle | | | 85 | 95 | % | | 3 |
| Switch Current Limit Blanking Time | | | 130 | 260 | ns | | 3 |
| Error Amplifier Transconductance | gm | 1100 | 1500 | 1900 | µmho | ∆IC = ±25µA | 2 |
| Error Amplifier Transconductance over full temperature range | gm | 700 | | 2300 | µmho | | 2 |
| Error Amplifier Sink Current | | | 1400 | 2400 | µA | VFB = VREF + 150mV, VC = 1.5V | 2 |
| Feedback Input Current | IFB | | 250 | 550 | nA | VFB = VREF | 2 |
| Feedback Input Current over full temperature range | IFB | | | 900 | nA | | 2 |
| Reference Voltage Line Regulation | | | 0.01 | 0.03 | %/V | 2.7V ≤ VIN ≤ 25V, VC = 0.8V | 2 |
| Negative Feedback Reference Voltage Line Regulation | | | 0.01 | 0.05 | %/V | 2.7V ≤ VIN ≤ 25V, VC = 0.8V | 2 |
| Operating Junction Temperature Range Industrial | TJ | -40 | | 125 | °C | I grade | 2 |
| Supply Voltage | | | | 30 | V | | 2 |
| Switch Voltage LT1377 | | | | 35 | V | LT1372/LT1377 | 2 |
| S/S Pin Voltage | | | | 30 | V | | 2 |
| Feedback Pin Voltage transient | | -10 | | 10 | V | Transient, 10ms | 2 |
| Feedback Pin Current | | | | 10 | mA | | 2 |
| Negative Feedback Pin Voltage transient | | -10 | | 10 | V | Transient, 10ms | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Lead Temperature | | | | 300 | °C | Soldering, 10 sec | 2 |
| Thermal Resistance Junction to Ambient S8 | θJA | | 120 | | °C/W | S8 package | 2 |
## CAD (KiCad official)
- Symbol: `LT1377IS8#PBF`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `lt1377is8-pbf-etched.step` / `lt1377is8-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt1377is8-pbf.step` / `lt1377is8-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/13727fbs.pdf) (12 pp, sha256 `cfd807e8c927796b`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt1377is8-pbf-datasheet.pdf)