3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT1372IS8#PBF
Analog Devices · DC-DC Converters · SO-8
LT1372IS8#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VC | passive | Compensation pin, the error amplifier output and current comparator input, used with an RC network to ground for loop compensation, current-limit clamping and soft start; pulling it below the control pin threshold (about 1V typical) idles the switch. |
| 2 | FB | input | Positive output voltage sense input to the error amplifier, which references the internal 1.245V reference, and the oscillator frequency-shift input; the load on FB should not exceed 250µA when the NFB pin is used. |
| 3 | NFB | input | Negative output voltage sense pin that regulates at -2.49V through a 100k source resistor, normally left open in positive-output applications. |
| 4 | S/S | input | Logic-compatible active-low shutdown and synchronization pin with a typical shutdown threshold of 1.3V; it can be pulled high, tied to VIN or left floating for normal operation, and synchronized between 600kHz and 800kHz (LT1372) or 1.2MHz and 1.6MHz (LT1377). |
| 5 | VIN | power_in | Supply input, operating from 2.7V to 25V, that must be bypassed with 10µF or more; the part enters undervoltage lockout and stops switching when VIN drops below 2.5V. |
| 6 | GND S | power_in | Ground sense pin that is the clean ground reference for the internal reference, error amplifier and negative feedback amplifier, and must be kept free of large ground currents. |
| 7 | GND | power_in | Power ground, the emitter connection of the power switch carrying large currents, to be connected directly to a good quality ground plane. |
| 8 | VSW | output | Collector of the internal power switch, which carries large currents and is limited to 1.5A; the switch breakdown voltage is 35V minimum for LT1372/LT1377, so the traces should be kept short. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reference Voltage (measured at FB pin) | VREF | 1.23 | 1.245 | 1.26 | V | Measured at Feedback Pin | 2 |
| Reference Voltage (VC = 0.8V, full temperature range) | VREF | 1.225 | 1.245 | 1.265 | V | VC = 0.8V; ● full operating temperature range | 2 |
| Feedback Input Current | IFB | 250 | 550 | nA | VFB = VREF | 2 | |
| Feedback Input Current (full temperature range) | IFB | 900 | nA | ● full operating temperature range | 2 | ||
| Reference Voltage Line Regulation | 0.01 | 0.03 | %/V | 2.7V ≤ VIN ≤ 25V, VC = 0.8V; ● | 2 | ||
| Negative Feedback Reference Voltage | VNFB | -2.54 | -2.49 | -2.44 | V | Measured at Negative Feedback Pin | 2 |
| Negative Feedback Reference Voltage (Feedback pin open, full temperature range) | VNFB | -2.57 | -2.49 | -2.41 | V | Feedback Pin Open, VC = 0.8V; ● | 2 |
| Negative Feedback Input Current | INFB | -45 | -30 | -15 | µA | VNFB = VNFR; ● | 2 |
| Negative Feedback Reference Voltage Line Regulation | 0.01 | 0.05 | %/V | 2.7V ≤ VIN ≤ 25V, VC = 0.8V; ● | 2 | ||
| Error Amplifier Transconductance | gm | 1100 | 1500 | 1900 | µmho | ΔIC = ±25µA | 2 |
| Error Amplifier Transconductance (full temperature range) | gm | 700 | 2300 | µmho | ● | 2 | |
| Error Amplifier Source Current | 120 | 200 | 350 | µA | VFB = VREF, 150mV, VC = 1.5V; ● | 2 | |
| Error Amplifier Sink Current | 1400 | 2400 | µA | VFB = VREF + 150mV, VC = 1.5V; ● | 2 | ||
| Error Amplifier Clamp Voltage (high) | 1.7 | 1.95 | 2.3 | V | High Clamp, VFB = 1V | 2 | |
| Error Amplifier Clamp Voltage (low) | 0.25 | 0.4 | 0.52 | V | Low Clamp, VFB = 1.5V | 2 | |
| VC Pin Threshold | 0.8 | 1 | 1.25 | V | Duty Cycle = 0% | 2 | |
| Switching Frequency LT1372 | f | 450 | 500 | 550 | kHz | 2.7V ≤ VIN ≤ 25V | 2 |
| Switching Frequency LT1372 (0°C to 125°C) | f | 430 | 500 | 580 | kHz | 0°C ≤ TJ ≤ 125°C; ● | 2 |
| Switching Frequency LT1372 (I grade, low temperature) | f | 400 | 580 | kHz | -40°C ≤ TJ < 0°C (I Grade) | 2 | |
| Maximum Switch Duty Cycle | 85 | 95 | % | ● | 3 | ||
| Switch Current Limit Blanking Time | 130 | 260 | ns | 3 | |||
| Output Switch Breakdown Voltage LT1372/LT1377 | BV | 35 | 47 | V | LT1372/LT1377; ● | 3 | |
| Output Switch On Resistance | VSAT | 0.5 | 0.8 | Ω | ISW = 1A; ● | 3 | |
| Switch Current Limit (50% duty cycle) | ILIM | 1.5 | 1.9 | 2.7 | A | Duty Cycle = 50%; ● | 3 |
| Switch Current Limit (80% duty cycle) | ILIM | 1.3 | 1.7 | 2.5 | A | Duty Cycle = 80% (Note 2); ● | 3 |
| Supply Current Increase During Switch On-Time | ΔIIN | 15 | 25 | mA/A | 3 | ||
| Minimum Input Voltage | 2.4 | 2.7 | V | ● | 3 | ||
| Supply Current | IQ | 4 | 5.5 | mA | 2.7V ≤ VIN ≤ 25V; ● | 3 | |
| Shutdown Supply Current (0°C to 125°C) | 12 | 30 | µA | 2.7V ≤ VIN ≤ 25V, VS/S ≤ 0.6V, 0°C ≤ TJ ≤ 125°C; ● | 3 | ||
| Shutdown Supply Current (I grade, low temperature) | 50 | µA | -40°C ≤ TJ < 0°C (I Grade) | 3 | |||
| Shutdown Threshold | 0.6 | 1.3 | 2 | V | 2.7V ≤ VIN ≤ 25V; ● | 3 | |
| Shutdown Delay | 5 | 12 | 25 | µs | ● | 3 | |
| S/S Pin Input Current | -10 | 15 | µA | 0V ≤ VS/S ≤ 5V; ● | 3 | ||
| Synchronization Frequency Range LT1372 | 600 | 800 | kHz | ● | 3 | ||
| Supply Voltage | 30 | V | 2 | ||||
| Switch Voltage LT1372/LT1377 | 35 | V | LT1372/LT1377 | 2 | |||
| S/S Pin Voltage | 30 | V | 2 | ||||
| Feedback Pin Voltage | -10 | 10 | V | Transient, 10ms | 2 | ||
| Feedback Pin Current | 10 | mA | 2 | ||||
| Negative Feedback Pin Voltage | -10 | 10 | V | Transient, 10ms | 2 | ||
| Operating Junction Temperature Range (Industrial) | TJ | -40 | 125 | °C | Industrial grade (I) | 2 | |
| Short Circuit Junction Temperature | TJ | 0 | 150 | °C | Short circuit | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Lead Temperature | 300 | °C | Soldering, 10 sec | 2 | |||
| Input Voltage Operating Range | VIN | 2.7 | 25 | V | Input voltage range stated in operating description | 6 | |
| Feedback Pin Load Current (when NFB pin is used) | 250 | µA | NFB pin used | 5 | |||
| Thermal Resistance Junction-to-Ambient (S8) | θJA | 120 | °C/W | S8 (SO-8) package | 2 |
CAD (KiCad official)
- Symbol:
LT1372IS8#PBF - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lt1372is8-pbf-etched.step/lt1372is8-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1372is8-pbf.step/lt1372is8-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (12 pp, sha256
cfd807e8c927796b, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).