main
Ray Publish 0.1.0 b37fa06

LT1372HVCS8#PBF

Analog Devices · DC-DC Converters · SO-8

LT1372HVCS8#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VC passive Compensation pin, the error amplifier output and current comparator input, used for frequency compensation, current limit adjustment and soft start, with duty cycle going to zero when pulled below the control pin threshold.
2 FB input Positive output voltage sense pin and inverting error amplifier input referenced to a 1.245V internal reference; load on this pin should not exceed 250µA when the NFB pin is used.
3 NFB input Negative feedback pin for negative output voltage sensing, connected to the inverting input of the negative feedback amplifier through a 100k source resistor.
4 S/S input Shutdown and synchronization pin, active low with a typical 1.3V shutdown threshold, synchronizable between 600kHz and 800kHz (LT1372) or 1.2MHz and 1.6MHz (LT1377).
5 VIN power_in Input supply pin to be bypassed with 10µF or more, with the part entering undervoltage lockout when VIN drops below 2.5V.
6 GND S power_in Ground sense pin, a clean ground to which the internal reference, error amplifier and negative feedback amplifier are referred, to be kept free of large ground currents.
7 GND power_in Ground pin, the emitter connection of the power switch carrying large currents, to be connected directly to a good quality ground plane.
8 VSW output Switch pin, the collector of the internal power switch carrying large currents, with traces kept as short as possible to minimize radiation and voltage spikes.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package SO-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Reference Voltage VREF 1.23 1.245 1.26 V Measured at Feedback Pin 2
Reference Voltage over temperature VREF 1.225 1.245 1.265 V VC = 0.8V, over full operating temperature range 2
Negative Feedback Reference Voltage VNFB -2.54 -2.49 -2.44 V Measured at Negative Feedback Pin 2
Negative Feedback Reference Voltage over temperature VNFB -2.57 -2.49 -2.41 V Feedback Pin Open, VC = 0.8V, over full operating temperature range 2
Negative Feedback Input Current INFB -45 -30 -15 µA VNFB = VNFR, over full operating temperature range 2
Feedback Input Current IFB 250 550 nA VFB = VREF 2
Feedback Input Current over temperature IFB 900 nA Over full operating temperature range 2
Reference Voltage Line Regulation 0.01 0.03 %/V 2.7V ≤ VIN ≤ 25V, VC = 0.8V, over full operating temperature range 2
Negative Feedback Reference Voltage Line Regulation 0.01 0.05 %/V 2.7V ≤ VIN ≤ 25V, VC = 0.8V, over full operating temperature range 2
Error Amplifier Transconductance gm 1100 1500 1900 µmho ΔIC = ±25µA 2
Error Amplifier Transconductance over temperature gm 700 2300 µmho Over full operating temperature range 2
Error Amplifier Source Current 120 200 350 µA VFB = VREF, 150mV, VC = 1.5V, over full operating temperature range 2
Error Amplifier Sink Current 1400 2400 µA VFB = VREF + 150mV, VC = 1.5V, over full operating temperature range 2
Error Amplifier High Clamp Voltage 1.7 1.95 2.3 V High Clamp, VFB = 1V 2
Error Amplifier Low Clamp Voltage 0.25 0.4 0.52 V Low Clamp, VFB = 1.5V 2
VC Pin Threshold 0.8 1 1.25 V Duty Cycle = 0% 2
Switching Frequency LT1372 f 450 500 550 kHz 2.7V ≤ VIN ≤ 25V 2
Switching Frequency LT1372 over temperature f 430 500 580 kHz 0°C ≤ TJ ≤ 125°C, over full operating temperature range 2
Maximum Switch Duty Cycle 85 95 % Over full operating temperature range 3
Switch Current Limit Blanking Time 130 260 ns 3
Output Switch Breakdown Voltage LT1372HV BV 42 47 V 0°C ≤ TJ ≤ 125°C, over full operating temperature range 3
Output Switch On Resistance VSAT 0.5 0.8 Ω ISW = 1A, over full operating temperature range 3
Switch Current Limit at 50% duty cycle ILIM 1.5 1.9 2.7 A Duty Cycle = 50%, over full operating temperature range 3
Switch Current Limit at 80% duty cycle ILIM 1.3 1.7 2.5 A Duty Cycle = 80% (Note 2), over full operating temperature range 3
Supply Current Increase During Switch On-Time ΔIIN 15 25 mA/A 3
Minimum Input Voltage 2.4 2.7 V Over full operating temperature range 3
Supply Current IQ 4 5.5 mA 2.7V ≤ VIN ≤ 25V, over full operating temperature range 3
Shutdown Supply Current 12 30 µA 2.7V ≤ VIN ≤ 25V, VS/S ≤ 0.6V, 0°C ≤ TJ ≤ 125°C, over full operating temperature range 3
Shutdown Threshold 0.6 1.3 2 V 2.7V ≤ VIN ≤ 25V, over full operating temperature range 3
Shutdown Delay 5 12 25 µs Over full operating temperature range 3
S/S Pin Input Current -10 15 µA 0V ≤ VS/S ≤ 5V, over full operating temperature range 3
Synchronization Frequency Range LT1372 600 800 kHz Over full operating temperature range 3
Supply Voltage 30 V 2
Switch Voltage LT1372HV 42 V LT1372HV 2
S/S Pin Voltage 30 V 2
Feedback Pin Voltage -10 10 V Transient, 10ms 2
Feedback Pin Current 10 mA 2
Negative Feedback Pin Voltage -10 10 V Transient, 10ms 2
Operating Junction Temperature Range Commercial TJ 0 125 °C Commercial grade, units shipped prior to Date Code 9552 rated 100°C maximum 2
Short Circuit Junction Temperature TJ 0 150 °C Short circuit 2
Storage Temperature Range -65 150 °C 2
Lead Temperature 300 °C Soldering, 10 sec 2
Thermal Resistance Junction to Ambient S8 θJA 120 °C/W S8 package, TJMAX = 125°C 2

CAD (KiCad official)

  • Symbol: LT1372HVCS8#PBF
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SO-8 (KiCad packages3D, STEP)
  • 3D model files: lt1372hvcs8-pbf-etched.step / lt1372hvcs8-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt1372hvcs8-pbf.step / lt1372hvcs8-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (12 pp, sha256 cfd807e8c927796b, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF