main
Ray
Publish 0.1.0
3c2011d
LT1308BIS8#PBF
Analog Devices · DC-DC Converters · SO-8
LT1308BIS8#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VC | passive | Compensation pin for the error amplifier; connect a series RC from this pin to ground (typical values 47kΩ and 100pF) and minimize the trace area at VC. |
| 2 | FB | input | Feedback input with a 1.22V reference; set VOUT = 1.22V(1 + R1/R2), minimize the trace area at FB, and keep the current into FB within ±1mA absolute maximum. |
| 3 | SHDN | input | Shutdown input: ground to turn the switcher off, tie to 1V or more to enable, and it does not need to be tied to VIN; SHDN voltage is rated to 10V maximum. |
| 4 | GND | power_in | Ground; connect directly to the local ground plane, which should enclose all components associated with the device and also acts as a heat sink. |
| 5 | SW | output | Switch pin that connects the inductor and diode; minimize trace area to keep EMI down, with an absolute maximum rating of -0.4V to 36V. |
| 6 | VIN | power_in | Supply pin with a 1V to 10V input voltage range; it must have a local bypass capacitor placed right at the pin connected directly to ground. |
| 7 | LBI | input | Low-battery detector input with a 200mV reference; the voltage on LBI must stay between -100mV and 1V, and the pin should float if unused. |
| 8 | LBO | output | Open-collector low-battery detector output that can sink 50μA, with a 220kΩ pull-up recommended; it is high impedance when SHDN is grounded. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Quiescent Current, switching (LT1308B) | IQ | 2.5 | 4 | mA | Switching, LT1308B | 3 | |
| Quiescent Current, shutdown | IQ | 0.01 | 1 | μA | VSHDN = 0V | 3 | |
| Feedback Voltage | VFB | 1.19 | 1.22 | 1.25 | V | 3 | |
| FB Pin Bias Current | IB | 27 | 80 | nA | 3 | ||
| Reference Line Regulation | 0.05 | 0.4 | %/V | 1.1V ≤ VIN ≤ 2V | 3 | ||
| Reference Line Regulation | 0.01 | 0.2 | %/V | 2V ≤ VIN ≤ 10V | 3 | ||
| Minimum Input Voltage | 0.92 | 1 | V | 3 | |||
| Switching Frequency | fOSC | 500 | 600 | 750 | kHz | 4 | |
| Maximum Duty Cycle | 82 | 90 | % | 4 | |||
| Switch Current Limit | 2 | 3 | 4.5 | A | Duty Cycle = 30% (Note 4) | 4 | |
| Switch VCESAT | VCESAT | 290 | 350 | mV | ISW = 2A (25°C, -40°C), VIN = 1.5V | 4 | |
| Switch VCESAT | VCESAT | 330 | 400 | mV | ISW = 2A (85°C), VIN = 1.5V | 4 | |
| Shutdown Pin Current | 2 | 5 | μA | VSHDN = 1.1V | 4 | ||
| Shutdown Pin Current | 20 | 35 | μA | VSHDN = 6V | 4 | ||
| Shutdown Pin Current | 0.01 | 0.1 | μA | VSHDN = 0V | 4 | ||
| LBI Threshold Voltage | 193 | 200 | 207 | mV | l: industrial -40°C to 85°C | 4 | |
| LBI Threshold Voltage | 196 | 200 | 204 | mV | Not marked l (TA = 25°C per table note) | 4 | |
| LBO Output Low | 0.1 | 0.25 | V | ISINK = 50μA | 4 | ||
| LBO Leakage Current | 0.01 | 0.1 | μA | VLBI = 250mV, VLBO = 5V | 4 | ||
| LBI Input Bias Current | 33 | 100 | nA | VLBI = 150mV | 4 | ||
| Switch Leakage Current | 0.01 | 10 | μA | VSW = 5V | 4 | ||
| Error Amp Transconductance | gm | 60 | μmhos | ΔI = 5μA | 3 | ||
| Error Amp Voltage Gain | AV | 100 | V/V | 3 | |||
| Low-Battery Detector Gain | 3000 | V/V | 4 | ||||
| VIN, SHDN, LBO Voltage | 10 | V | 2 | ||||
| SW Voltage | -0.4 | 36 | V | 2 | |||
| VC Voltage | 2 | V | 2 | ||||
| LBI Voltage | -0.1 | 1 | V | 2 | |||
| Current into FB Pin | -1 | 1 | mA | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering) | 300 | °C | 10 sec | 2 | |||
| Operating Temperature Range (Industrial) | -40 | 85 | °C | Industrial grade | 2 | ||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Thermal Resistance, junction to ambient | θJA | 190 | °C/W | 8-lead plastic SO (S8 package) | 2 | ||
| Input Voltage Range | VIN | 1 | 10 | V | Operating input range stated in datasheet description | 1 | |
| SHDN Enable Voltage | VSHDN | 1 | V | To enable the device, tie SHDN to 1V or more | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | connected to these pins also functions as a heat sink. For the TSSOP package, connect all pins to ground copper | 6 |
CAD (KiCad official)
- Symbol:
LT1308BIS8#PBF - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lt1308bis8-pbf-etched.step/lt1308bis8-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1308bis8-pbf.step/lt1308bis8-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
11d1f4d87cd83de1, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT1308BIS8#PBF
**Analog Devices** · DC-DC Converters · SO-8
LT1308BIS8#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VC | passive | Compensation pin for the error amplifier; connect a series RC from this pin to ground (typical values 47kΩ and 100pF) and minimize the trace area at VC. |
| 2 | FB | input | Feedback input with a 1.22V reference; set VOUT = 1.22V(1 + R1/R2), minimize the trace area at FB, and keep the current into FB within ±1mA absolute maximum. |
| 3 | SHDN | input | Shutdown input: ground to turn the switcher off, tie to 1V or more to enable, and it does not need to be tied to VIN; SHDN voltage is rated to 10V maximum. |
| 4 | GND | power_in | Ground; connect directly to the local ground plane, which should enclose all components associated with the device and also acts as a heat sink. |
| 5 | SW | output | Switch pin that connects the inductor and diode; minimize trace area to keep EMI down, with an absolute maximum rating of -0.4V to 36V. |
| 6 | VIN | power_in | Supply pin with a 1V to 10V input voltage range; it must have a local bypass capacitor placed right at the pin connected directly to ground. |
| 7 | LBI | input | Low-battery detector input with a 200mV reference; the voltage on LBI must stay between -100mV and 1V, and the pin should float if unused. |
| 8 | LBO | output | Open-collector low-battery detector output that can sink 50μA, with a 220kΩ pull-up recommended; it is high impedance when SHDN is grounded. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Quiescent Current, switching (LT1308B) | IQ | | 2.5 | 4 | mA | Switching, LT1308B | 3 |
| Quiescent Current, shutdown | IQ | | 0.01 | 1 | μA | VSHDN = 0V | 3 |
| Feedback Voltage | VFB | 1.19 | 1.22 | 1.25 | V | | 3 |
| FB Pin Bias Current | IB | | 27 | 80 | nA | | 3 |
| Reference Line Regulation | | | 0.05 | 0.4 | %/V | 1.1V ≤ VIN ≤ 2V | 3 |
| Reference Line Regulation | | | 0.01 | 0.2 | %/V | 2V ≤ VIN ≤ 10V | 3 |
| Minimum Input Voltage | | | 0.92 | 1 | V | | 3 |
| Switching Frequency | fOSC | 500 | 600 | 750 | kHz | | 4 |
| Maximum Duty Cycle | | 82 | 90 | | % | | 4 |
| Switch Current Limit | | 2 | 3 | 4.5 | A | Duty Cycle = 30% (Note 4) | 4 |
| Switch VCESAT | VCESAT | | 290 | 350 | mV | ISW = 2A (25°C, -40°C), VIN = 1.5V | 4 |
| Switch VCESAT | VCESAT | | 330 | 400 | mV | ISW = 2A (85°C), VIN = 1.5V | 4 |
| Shutdown Pin Current | | | 2 | 5 | μA | VSHDN = 1.1V | 4 |
| Shutdown Pin Current | | | 20 | 35 | μA | VSHDN = 6V | 4 |
| Shutdown Pin Current | | | 0.01 | 0.1 | μA | VSHDN = 0V | 4 |
| LBI Threshold Voltage | | 193 | 200 | 207 | mV | l: industrial -40°C to 85°C | 4 |
| LBI Threshold Voltage | | 196 | 200 | 204 | mV | Not marked l (TA = 25°C per table note) | 4 |
| LBO Output Low | | | 0.1 | 0.25 | V | ISINK = 50μA | 4 |
| LBO Leakage Current | | | 0.01 | 0.1 | μA | VLBI = 250mV, VLBO = 5V | 4 |
| LBI Input Bias Current | | | 33 | 100 | nA | VLBI = 150mV | 4 |
| Switch Leakage Current | | | 0.01 | 10 | μA | VSW = 5V | 4 |
| Error Amp Transconductance | gm | | 60 | | μmhos | ΔI = 5μA | 3 |
| Error Amp Voltage Gain | AV | | 100 | | V/V | | 3 |
| Low-Battery Detector Gain | | | 3000 | | V/V | | 4 |
| VIN, SHDN, LBO Voltage | | | | 10 | V | | 2 |
| SW Voltage | | -0.4 | | 36 | V | | 2 |
| VC Voltage | | | | 2 | V | | 2 |
| LBI Voltage | | -0.1 | | 1 | V | | 2 |
| Current into FB Pin | | -1 | | 1 | mA | | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Lead Temperature (Soldering) | | | | 300 | °C | 10 sec | 2 |
| Operating Temperature Range (Industrial) | | -40 | | 85 | °C | Industrial grade | 2 |
| Maximum Junction Temperature | TJMAX | | | 125 | °C | | 2 |
| Thermal Resistance, junction to ambient | θJA | | 190 | | °C/W | 8-lead plastic SO (S8 package) | 2 |
| Input Voltage Range | VIN | 1 | | 10 | V | Operating input range stated in datasheet description | 1 |
| SHDN Enable Voltage | VSHDN | 1 | | | V | To enable the device, tie SHDN to 1V or more | 6 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | connected to these pins also functions as a heat sink. For the TSSOP package, connect all pins to ground copper | 6 |
## CAD (KiCad official)
- Symbol: `LT1308BIS8#PBF`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `lt1308bis8-pbf-etched.step` / `lt1308bis8-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt1308bis8-pbf.step` / `lt1308bis8-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/1308abfb.pdf) (20 pp, sha256 `11d1f4d87cd83de1`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt1308bis8-pbf-datasheet.pdf)