← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# LSM6DSV16XTR++**STMicroelectronics** · Attitude Sensor/Gyroscope · LGA-14(2.5x3)++LSM6DSV16XTR from STMicroelectronics, in a LGA-14(2.5x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SDO/SA0 | bidirectional | SPI 4-wire interface serial data output (SDO) or I2C least-significant bit of the device address (SA0). Function selected by the active serial interface. |+| 2 | SDx/AH1/Qvar1 | bidirectional | Mode 1: analog hub input 1 (AH1) or Qvar electrode 1 when analog hub / Qvar is enabled; tie to Vdd_IO or GND if unused. Mode 2: I2C serial data master (MSDA). Mode 3: auxiliary SPI 3/4-wire serial data input (SDI_Aux) and 3-wire output (SDO_Aux). |+| 3 | SCx/AH2/Qvar2 | bidirectional | Mode 1: analog hub input 2 (AH2) or Qvar electrode 2 when analog hub / Qvar is enabled; tie to Vdd_IO or GND if unused. Mode 2: I2C serial clock master (MSCL). Mode 3: auxiliary SPI 3/4-wire serial port clock (SPC_Aux). |+| 4 | INT1 | output | Programmable interrupt 1, available in both I2C and SPI modes. Used for host-side event notification (data-ready, motion, free-fall, wake-up, FSM/MLC output, etc.). |+| 5 | Vdd_IO | power_in | Power supply for the digital I/O pins. Extended range 1.08 V to 3.6 V. Recommended 100 nF decoupling capacitor. |+| 6 | GND | power_in | 0 V supply (ground reference). Connect to system ground. |+| 7 | GND | power_in | 0 V supply (ground reference). Connect to system ground. |+| 8 | Vdd | power_in | Analog supply voltage: 1.71 V to 3.6 V (typ. 1.8 V). Recommended 100 nF decoupling capacitor. |+| 9 | INT2 | bidirectional | Programmable interrupt 2 (INT2) / data enable (DEN). In Mode 2, also functions as I2C master external synchronization signal (MDRDY). Direction depends on the selected function. |+| 10 | OCS_Aux | input | Mode 1 & 2: connect to Vdd_IO or leave electrically unconnected. Mode 3: enable for the auxiliary SPI 3/4-wire interface (active-low chip select for aux SPI). |+| 11 | SDO_Aux | output | Mode 1 & 2: connect to Vdd_IO or leave electrically unconnected. Mode 3: auxiliary SPI 4-wire serial data output (SDO_Aux); leave unconnected when the auxiliary SPI is used in 3-wire mode. |+| 12 | CS | input | I2C / MIPI I3C / SPI mode selection (active-low chip select). CS = 1: SPI idle mode and I2C / MIPI I3C communication enabled. CS = 0: SPI communication enabled and I2C / MIPI I3C disabled. |+| 13 | SCL | input | I2C / MIPI I3C serial clock (SCL) or SPI serial port clock (SPC). Shared clock line for the primary serial interface. |+| 14 | SDA | bidirectional | I2C / MIPI I3C serial data (SDA), SPI serial data input (SDI), or 3-wire SPI serial data output (SDO). Direction depends on the active protocol and transfer phase. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LGA-14(2.5x3) |+| Category | Sensor |+| Pins | 14 |++## Ordering variants++- `LSM6DSV16XTR`++## CAD (KiCad official)++- Symbol: `LSM6DSV16XTR`+- Footprint: `Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm`+- 3D model: LGA-14(2.5x3) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](docs/lsm6dsv16xtr-datasheet.pdf) (198 pp, sha256 `ec53c0e5952fc0c9`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lsm6dsv16xtr-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "lsm6dsv16xtr",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics Attitude Sensor/Gyroscope, LGA-14(2.5x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "sensor",+ "lsm6dsv16xtr"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lsm6dsv16xtr.kicad_sym",+ "lsm6dsv16xtr.kicad_mod",+ "lsm6dsv16xtr.glb",+ "lsm6dsv16xtr.step",+ "lsm6dsv16xtr.lbr",+ "docs/hero.png",+ "docs/lsm6dsv16xtr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}