3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLPC1342FHN33
NXP Semicon · NXP MCU · QFN-32-EP(7x7)
LPC1342FHN33 from NXP Semicon, in a QFN-32-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PIO2_0/DTR | bidirectional | General purpose digital I/O pin PIO2_0 with alternate output DTR (Data Terminal Ready for UART); internal pull-up enabled at reset, 5 V tolerant pad. |
| 2 | RESET/PIO0_0 | input | External reset input with 20 ns glitch filter, where a LOW-going pulse as short as 50 ns resets the device; 5 V tolerant pad, and RESET is not available in Deep power-down mode (use WAKEUP instead). |
| 3 | PIO0_1/CLKOUT/CT32B0_MAT2/USB_FTOGGLE | bidirectional | General purpose I/O PIO0_1 with alternate outputs CLKOUT, CT32B0_MAT2 and USB_FTOGGLE (USB 1 ms start-of-frame, LPC1342/43 only); a LOW level during reset starts the ISP command handler or USB enumeration. |
| 4 | XTALIN | input | Input to the oscillator circuit and internal clock generator; input voltage must not exceed 1.8 V, and it may be left floating or grounded (grounding preferred) when the system oscillator is not used. |
| 5 | XTALOUT | output | Output from the oscillator amplifier; it should be left floating when the system oscillator is not used. |
| 6 | VDD | power_in | 3.3 V supply voltage to the internal regulator, the external rail and the ADC, also used as the ADC reference voltage. |
| 7 | PIO1_8/CT16B1_CAP0 | bidirectional | General purpose digital I/O pin PIO1_8 with CT16B1_CAP0 capture input 0 for 16-bit timer 1; 5 V tolerant pad. |
| 8 | PIO0_2/SSEL0/CT16B0_CAP0 | bidirectional | General purpose digital I/O pin PIO0_2 with SSEL0 slave select for SSP0 and CT16B0_CAP0 capture input 0 for 16-bit timer 0; 5 V tolerant pad. |
| 9 | PIO0_3/USB_VBUS | bidirectional | General purpose digital I/O pin PIO0_3 that, on LPC1342/43, monitors USB bus power (USB_VBUS) and selects ISP (LOW) or USB enumeration (HIGH) when sampled during reset; 5 V tolerant pad. |
| 10 | PIO0_4/SCL | bidirectional | Open-drain general purpose I/O pin PIO0_4 and I2C-bus clock SCL, compliant with I2C standard mode and Fast-mode Plus, with high-current sink only when Fast-mode Plus is selected. |
| 11 | PIO0_5/SDA | bidirectional | Open-drain general purpose I/O pin PIO0_5 and I2C-bus data SDA, compliant with I2C standard mode and Fast-mode Plus, with high-current sink only when Fast-mode Plus is selected. |
| 12 | PIO1_9/CT16B1_MAT0 | bidirectional | General purpose digital I/O pin PIO1_9 with CT16B1_MAT0 match output 0 for 16-bit timer 1; 5 V tolerant pad. |
| 13 | USB_DM | bidirectional | USB bidirectional D- line (LPC1342/43 only), designed to USB 2.0 Full-speed and Low-speed specifications and not 5 V tolerant. |
| 14 | USB_DP | bidirectional | USB bidirectional D+ line (LPC1342/43 only), designed to USB 2.0 Full-speed and Low-speed specifications and not 5 V tolerant. |
| 15 | PIO0_6/USB_CONNECT/SCK0 | bidirectional | General purpose digital I/O pin PIO0_6 with USB_CONNECT output to switch an external 1.5 kΩ resistor for SoftConnect (LPC1342/43) and SCK0 serial clock for SSP0; 5 V tolerant pad. |
| 16 | PIO0_7/CTS | bidirectional | General purpose digital I/O pin PIO0_7 with high-current output driver and CTS (Clear To Send) input for UART; 5 V tolerant pad. |
| 17 | PIO0_8/MISO0/CT16B0_MAT0 | bidirectional | General purpose digital I/O pin PIO0_8 with MISO0 (Master In Slave Out) for SSP0 and CT16B0_MAT0 match output 0 for 16-bit timer 0; 5 V tolerant pad. |
| 18 | PIO0_9/MOSI0/CT16B0_MAT1/SWO | bidirectional | General purpose digital I/O pin PIO0_9 with MOSI0 (Master Out Slave In) for SSP0, CT16B0_MAT1 match output and SWO serial wire trace output; 5 V tolerant pad. |
| 19 | SWCLK/PIO0_10/SCK0/CT16B0_MAT2 | input | Serial wire clock SWCLK input (internal pull-up at reset) that is multiplexed with general purpose I/O PIO0_10, SCK0 serial clock for SSP0 and CT16B0_MAT2 output; 5 V tolerant pad. |
| 20 | PIO1_10/AD6/CT16B1_MAT1 | bidirectional | General purpose digital I/O pin PIO1_10 with A/D converter input 6 and CT16B1_MAT1 output; when used as ADC input the digital section is disabled and the pin is not 5 V tolerant. |
| 21 | R/PIO0_11/AD0/CT32B0_MAT3 | bidirectional | Reserved (R) in default state and must be configured for an alternate function in the IOCONFIG block; general purpose I/O PIO0_11 with A/D converter input 0 and CT32B0_MAT3 output, not 5 V tolerant when used as ADC input. |
| 22 | R/PIO1_0/AD1/CT32B1_CAP0 | bidirectional | Reserved (R) in default state and must be configured for an alternate function in the IOCONFIG block; general purpose I/O PIO1_0 with A/D converter input 1 and CT32B1_CAP0 capture input 0 for 32-bit timer 1, not 5 V tolerant when used as ADC input. |
| 23 | R/PIO1_1/AD2/CT32B1_MAT0 | bidirectional | Reserved (R) in default state and must be configured for an alternate function in the IOCONFIG block; general purpose I/O PIO1_1 with A/D converter input 2 and CT32B1_MAT0 match output 0 for 32-bit timer 1, not 5 V tolerant when used as ADC input. |
| 24 | R/PIO1_2/AD3/CT32B1_MAT1 | bidirectional | Reserved (R) in default state and must be configured for an alternate function in the IOCONFIG block; general purpose I/O PIO1_2 with A/D converter input 3 and CT32B1_MAT1 match output 1 for 32-bit timer 1, not 5 V tolerant when used as ADC input. |
| 25 | SWDIO/PIO1_3/AD4/CT32B1_MAT2 | bidirectional | Serial wire debug I/O SWDIO multiplexed with general purpose I/O PIO1_3, A/D converter input 4 and CT32B1_MAT2 match output 2 for 32-bit timer 1; 5 V tolerant pad. |
| 26 | PIO1_4/AD5/CT32B1_MAT3/WAKEUP | bidirectional | General purpose I/O PIO1_4 with A/D converter input 5, CT32B1_MAT3 output and WAKEUP pin with 20 ns glitch filter that must be pulled HIGH to enter and LOW to exit Deep power-down mode. |
| 27 | PIO1_11/AD7 | bidirectional | General purpose digital I/O pin PIO1_11 with A/D converter input 7; when used as ADC input the pin is not 5 V tolerant. |
| 28 | PIO3_2 | bidirectional | General purpose digital I/O pin PIO3_2 with internal pull-up at reset; 5 V tolerant pad with configurable pull-up/pull-down and hysteresis. |
| 29 | VDD | power_in | 3.3 V supply voltage to the internal regulator, the external rail and the ADC, also used as the ADC reference voltage. |
| 30 | PIO1_5/RTS/CT32B0_CAP0 | bidirectional | General purpose digital I/O pin PIO1_5 with RTS (Request To Send) output for UART and CT32B0_CAP0 capture input 0 for 32-bit timer 0; 5 V tolerant pad. |
| 31 | PIO1_6/RXD/CT32B0_MAT0 | bidirectional | General purpose digital I/O pin PIO1_6 with RXD receiver input for UART and CT32B0_MAT0 match output 0 for 32-bit timer 0; 5 V tolerant pad. |
| 32 | PIO1_7/TXD/CT32B0_MAT1 | bidirectional | General purpose digital I/O pin PIO1_7 with TXD transmitter output for UART and CT32B0_MAT1 match output 1 for 32-bit timer 0; 5 V tolerant pad. |
| 33 | VSS | power_in | Thermal pad that must be connected to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | QFN-32-EP(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (core and external rail) | VDD | 2 | 3.3 | 3.6 | V | 32 | |
| Input voltage (5 V tolerant I/O pins) | VI | -0.5 | 5.5 | V | 5 V tolerant I/O pins; only valid when the VDD supply voltage is present | 31 | |
| Supply current per supply pin | IDD | 100 | mA | per supply pin | 31 | ||
| Ground current per ground pin | ISS | 100 | mA | per ground pin | 31 | ||
| I/O latch-up current | Ilatch | 100 | mA | −(0.5VDD) < VI < (1.5VDD); Tj < 125 °C | 31 | ||
| Storage temperature | Tstg | -65 | 150 | °C | non-operating | 31 | |
| Maximum junction temperature | Tj(max) | 150 | °C | 31 | |||
| Total power dissipation (per package) | Ptot(pack) | 1.5 | W | based on package heat transfer, not device power consumption | 31 | ||
| Electrostatic discharge voltage | VESD | -6500 | 6500 | V | human body model; all pins | 31 | |
| LOW-level input current | IIL | 0.5 | 10 | nA | VI = 0 V; on-chip pull-up resistor disabled | 32 | |
| HIGH-level input current | IIH | 0.5 | 10 | nA | VI = VDD; on-chip pull-down resistor disabled | 32 | |
| OFF-state output current | IOZ | 0.5 | 10 | nA | VO = 0 V; VO = VDD; on-chip pull-up/down resistors disabled | 32 | |
| Input voltage (pin configured to provide a digital function) | VI | 0 | 5 | V | pin configured to provide a digital function | 32 | |
| Output voltage (output active) | VO | 0 | V | output active | 33 | ||
| Hysteresis voltage | Vhys | 0.4 | V | 33 | |||
| LOW-level output voltage | VOL | 0.4 | V | 2.5 V ≤ VDD ≤ 3.6 V; IOL = 4 mA | 33 | ||
| HIGH-level output current | IOH | -4 | mA | 2.5 V ≤ VDD ≤ 3.6 V; VOH = VDD − 0.4 V | 33 | ||
| HIGH-level output current | IOH | -3 | mA | 2.0 V ≤ VDD < 2.5 V; VOH = VDD − 0.4 V | 33 | ||
| LOW-level output current | IOL | 4 | mA | 2.5 V ≤ VDD ≤ 3.6 V; VOL = 0.4 V | 33 | ||
| LOW-level output current | IOL | 3 | mA | 2.0 V ≤ VDD < 2.5 V; VOL = 0.4 V | 33 | ||
| HIGH-level short-circuit output current | IOHS | -45 | mA | VOH = 0 V | 33 | ||
| LOW-level short-circuit output current | IOLS | 50 | mA | VOL = VDD | 33 | ||
| Pull-down current | Ipd | 10 | 50 | 150 | μA | VI = 5 V | 33 |
| Pull-up current | Ipu | -15 | -50 | -85 | μA | VI = 0 V | 33 |
| LOW-level output voltage (high-drive pin PIO0_7) | VOL | 0.4 | V | 2.5 V ≤ VDD ≤ 3.6 V; IOL = 4 mA | 33 | ||
| HIGH-level output current (high-drive pin PIO0_7) | IOH | 20 | mA | 2.5 V ≤ VDD ≤ 3.6 V; VOH = VDD − 0.4 V | 34 | ||
| HIGH-level output current (high-drive pin PIO0_7) | IOH | 12 | mA | 2.0 V ≤ VDD < 2.5 V; VOH = VDD − 0.4 V | 34 | ||
| LOW-level output current (high-drive pin PIO0_7) | IOL | 4 | mA | 2.5 V ≤ VDD ≤ 3.6 V; VOL = 0.4 V | 34 | ||
| LOW-level output current (high-drive pin PIO0_7) | IOL | 3 | mA | 2.0 V ≤ VDD < 2.5 V; VOL = 0.4 V | 34 | ||
| LOW-level output current (I2C pins, standard mode) | IOL | 3.5 | mA | VOL = 0.4 V; I2C-bus pins configured as standard mode pins; 2.5 V ≤ VDD ≤ 3.6 V | 34 | ||
| LOW-level output current (I2C pins, standard mode) | IOL | 3 | mA | VOL = 0.4 V; I2C-bus pins configured as standard mode pins; 2.0 V ≤ VDD < 2.5 V | 34 | ||
| LOW-level output current (I2C pins, Fast-mode Plus) | IOL | 20 | mA | VOL = 0.4 V; I2C-bus pins configured as Fast-mode Plus pins; 2.5 V ≤ VDD ≤ 3.6 V | 34 | ||
| LOW-level output current (I2C pins, Fast-mode Plus) | IOL | 16 | mA | VOL = 0.4 V; I2C-bus pins configured as Fast-mode Plus pins; 2.0 V ≤ VDD < 2.5 V | 34 | ||
| I2C input leakage current | ILI | 24 | μA | VI = VDD [16] | 34 | ||
| Crystal input voltage | Vi(xtal) | -0.5 | 1.8 | 1.95 | V | 34 | |
| Crystal output voltage | Vo(xtal) | -0.5 | 1.8 | 1.95 | V | 34 | |
| Internal RC oscillator frequency | fosc(RC) | 11.88 | 12 | 12.12 | MHz | 52 | |
| Oscillator frequency (external clock) | fosc | 1 | 25 | MHz | 51 | ||
| Endurance | Nendu | 10000 | 100000 | cycles | 50 | ||
| Retention time (powered) | tret | 10 | years | powered | 50 | ||
| Retention time (unpowered) | tret | 20 | years | unpowered | 50 | ||
| Erase time (sector or multiple consecutive sectors) | ter | 95 | 100 | 105 | ms | sector or multiple consecutive sectors | 50 |
| Programming time | tprog | 0.95 | 1 | 1.05 | ms | writing 256 bytes from RAM to flash | 50 |
| Differential linearity error | ED | -1 | 1 | LSB | 35 | ||
| Integral non-linearity | EL(adj) | -1.5 | 1.5 | LSB | 35 | ||
| Offset error | EO | -3.5 | 3.5 | LSB | 35 | ||
| Gain error | EG | 0.6 | % | 35 | |||
| Absolute error | ET | -4 | 4 | LSB | 35 | ||
| Rise time at power-up | tr | 0 | 500 | ms | at t = t1: 0 < VI ≤ 400 mV | 50 | |
| Wait time before power-up ramp | twait | 12 | μs | 50 | |||
| Input voltage at t = t1 on pin VDD (power-up) | VI | 0 | 400 | mV | at t = t1 on pin VDD | 50 | |
| USB pin OFF-state output current | IOZ | -10 | 10 | μA | 0V<VI < 3.3 V; footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 34 | |
| USB bus supply voltage | VBUS | 5.25 | V | footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 34 | ||
| USB differential input sensitivity voltage | VDI | 0.2 | V | /(D+) − (D−)/; footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 34 | ||
| USB differential common mode voltage range | VCM | 0.8 | 2.5 | V | includes VDI range; footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 34 | |
| USB single-ended receiver switching threshold voltage | Vth(rs)se | 0.8 | 2 | V | footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 34 | |
| USB LOW-level output voltage | VOL | 0.18 | V | for low-/full-speed; RL of 1.5 kΩ to 3.6 V; footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 34 | ||
| USB HIGH-level output voltage | VOH | 2.8 | 3.5 | V | driven; for low-/full-speed; RL of 15 kΩ to GND; footnote [17]: 3.0 V ≤ VDD ≤ 3.6 V | 35 |
CAD (KiCad official)
- Symbol:
LPC1342FHN33 - Footprint:
Package_DFN_QFN:QFN-32-1EP_7x7mm_P0.65mm_EP4.7x4.7mm - 3D model: QFN-32-EP(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.85 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lpc1342fhn33-etched.step/lpc1342fhn33-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lpc1342fhn33.step/lpc1342fhn33.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (74 pp, sha256
0c5c7c6ec2d41fb4, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).