LPA2010MSF

{
  "slug": "lpa2010msf",
  "version": "0.1.0",
  "type": "component",
  "description": "LOWPOWER Audio Amplifiers, MSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "amplifiers-comparators",
    "lpa2010msf",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "lpa2010msf.kicad_sym",
    "lpa2010msf.kicad_mod",
    "lpa2010msf.glb",
    "lpa2010msf.step",
    "lpa2010msf.lbr",
    "docs/hero.png",
    "docs/lpa2010msf-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "lpa2010msf-hero.glb",
    "lpa2010msf-hero.overlay.json",
    "lpa2010msf-etched.glb"
  ],
  "component": {
    "mpn": "LPA2010MSF",
    "manufacturer": "LOWPOWER",
    "package": "MSOP-8",
    "pin_count": 8,
    "category": "Amplifiers/Comparators",
    "subcategory": "Audio Amplifiers",
    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588903999877885952",
    "parts": {
      "symbol": "lpa2010msf.kicad_sym",
      "footprint": "lpa2010msf.kicad_mod",
      "model_3d": "lpa2010msf-hero.glb",
      "model_3d_plain": "lpa2010msf-etched.glb",
      "model_3d_step": "lpa2010msf-etched.step",
      "model_3d_step_plain": "lpa2010msf.step",
      "lbr": "lpa2010msf.lbr"
    },
    "distributor_links": {
      "lcsc": "C387737"
    },
    "distributor_check": {
      "checked_at": "2026-10-19T01:03:24Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": null,
        "status": "no match"
      },
      "mouser": {
        "pn": null,
        "status": "no match"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "SD",
        "type": "input",
        "description": "Active-low shutdown input: a logic low turns the amplifier off, and the datasheet gives VSD_L max 0.4 V and VSD_H min 1 V at VDD = 5 V."
      },
      {
        "number": "2",
        "name": "BYP",
        "type": "passive",
        "description": "Analog reference bypass pin, where the datasheet says to connect a 1 uF capacitor to GND; this capacitor sets the start-up rate and reduces supply noise coupling into the output."
      },
      {
        "number": "3",
        "name": "INP",
        "type": "input",
        "description": "Positive input of the amplifier, fed through the input capacitor Ci and input resistor Ri in the typical application."
      },
      {
        "number": "4",
        "name": "INN",
        "type": "input",
        "description": "Negative input of the amplifier, fed through Ci and Ri in the differential-input application schematic."
      },
      {
        "number": "5",
        "name": "VOP",
        "type": "output",
        "description": "Positive signal output that drives the speaker directly with VON, with no LC output filter needed for speaker traces about 100 mm or shorter."
      },
      {
        "number": "6",
        "name": "VDD",
        "type": "power_in",
        "description": "Supply voltage pin specified at 2.5 V to 5.5 V, where the outputs are disabled when VDD drops to 2.5 V or below."
      },
      {
        "number": "7",
        "name": "GND",
        "type": "power_in",
        "description": "Ground pin; the datasheet recommends placing the VDD decoupling and bypass capacitors as close to the chip pins as possible."
      },
      {
        "number": "8",
        "name": "VON",
        "type": "output",
        "description": "Negative signal output that drives the speaker differentially with VOP, with no LC output filter needed for short speaker traces."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: The BYP capacitor value conflicts within the datasheet: the pin table says 1 uF to GND, but the typi; The top-view drawing was only available as scrambled text, so pin positions were taken from the Func"
        ],
        "pages_sent": 9,
        "cost_usd": 0.0454,
        "at": "2026-10-19T01:01:04"
      },
      "datasheet": {
        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588903999877885952",
        "pages": 9,
        "sha256": "377bf893a000300f",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 8,
        "described": 8,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "lpa2010msf.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.9,
          3.0,
          0.95
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "847c4c5023fe1603fbd36900a5dcc4bd3901ba473f71d42c9a469f0236eaadf3",
        "checked": "2026-10-19",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "lpa2010msf-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.9,
          3.0,
          0.95
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "7864ca589cfe82281c7f1295eeedc0d7b623b65dfc4c058a98f5a71d48add3b1",
        "checked": "2026-10-19",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}