Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LP8869QPWPRQ1

Texas Instruments · LED Drivers · HTSSOP-20-EP

LP8869QPWPRQ1 from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input power pin that also serves as the input voltage OVP detection pin and the positive input of the input current sense; recommended VIN range is 4.5 V to 45 V.
2 LDO power_out Output of the internal LDO that requires a 1-µF decoupling capacitor to noise-free ground, placed as close to the chip as possible.
3 FSET passive DC-DC (boost or SEPIC) switching frequency setting resistor that must be connected to ground with a value from 24 kΩ to 219 kΩ for normal operation.
4 VDDIO/EN power_in Enable input for the device and supply input for the digital pins (VDDIO), with a recommended range of 0 V to 5.25 V.
5 FAULT output Open-drain fault signal output that may be left floating if unused.
6 SYNC input Input for synchronizing the DC-DC converter; connect to ground to disable spread spectrum or to VDDIO/EN to enable it when synchronization is not used.
7 PWM input PWM dimming input with a recommended range of 0 V to VDDIO/EN.
8 TSENSE passive Input for the NTC resistor divider used for automatic LED current reduction with an external temperature sensor; must be left floating if unused.
9 TSET passive Input for the NTC resistor divider used for external temperature sensing; must be connected to GND if unused.
10 ISET passive LED current setting resistor that must be connected to ground with a value from 20 kΩ to 129 kΩ for normal operation.
11 GND power_in Ground pin.
12 GND power_in GND pin for the LP8869-Q1; on the LP8867-Q1 this same pin is the OUT4 current sink output, which must be connected to ground if not used.
13 OUT3 output Current sink output that must be connected to ground if not used.
14 OUT2 output Current sink output that must be connected to ground if not used.
15 OUT1 output Current sink output that must be connected to ground if not used.
16 FB input DC-DC (boost or SEPIC) feedback input that must connect to the middle of a resistor divider between VOUT and ground, using feedback resistor values greater than 5 kΩ.
17 PGND power_in DC-DC (boost or SEPIC) power ground.
18 SW passive DC-DC (boost or SEPIC) switch pin.
19 SD output Power-line FET control output, open-drain (current sink type) that may be left floating if unused.
20 VSENSE_N input Negative input of the input current sense; connect to VIN when the input current sense resistor is not used.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20-EP
Category Nixie Tube Driver/LED Driver
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Voltage on pins VIN, VSENSE_N, SD, SW, FB -0.3 50 V 5
Voltage on pins OUT1, OUT2, OUT3, OUT4 -0.3 45 V 5
Voltage on pins LDO, SYNC, FSET, ISET, TSENSE, TSET, PWM, VDDIO/EN, FAULT -0.3 5.5 V 5
Ambient temperature TA -40 125 °C 5
Junction temperature TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
ESD Human-body model (HBM) V(ESD) -2000 2000 V Human-body model (HBM), per AEC Q100-002, all pins 5
ESD Charged-device model (CDM), corner pins V(ESD) -750 750 V Charged-device model (CDM), per AEC Q100-011, corner pins (1, 10, 11 and 20) 5
ESD Charged-device model (CDM), all pins V(ESD) -500 500 V Charged-device model (CDM), per AEC Q100-011, all pins 5
Input voltage VIN VIN 4.5 12 45 V 5
Voltage on pins SW, VSENSE_N, SD 0 45 V 5
Voltage on pins OUT1, OUT2, OUT3, OUT4 0 40 V 5
Voltage on pins FB, FSET, LDO, ISET, TSENSE, TSET, VDDIO/EN, FAULT 0 5.25 V 5
Voltage on pins SYNC, PWM 0 V 5
Standby supply current IQ 4.5 20 µA Device disabled, VVDDIO/EN = 0 V, VIN = 12 V 6
Active supply current IQ 5 12 mA VIN = 12 V, VOUT = 26 V, output current 80 mA/channel, converter ƒSW = 300 kHz 6
Output voltage VLDO 4.15 4.3 4.55 V VIN = 12 V 6
Dropout voltage VDR 120 300 430 mV 6
VIN OVP threshold voltage VOVP 41 42 44 V 6
VIN OCP threshold voltage, VIN - VSENSEN VOCP 135 160 186 mV 6
VIN UVLO Falling threshold VUVLO 3.7 3.85 4 V 6
VSENSE_N pin leakage ISENSE_N 0.1 3 µA VSENSE_N = 45V, EN = L 6
SD pin leakage ISD_LEAK 0.1 3 µA VSD = 45V, EN = L 6
SD pull down current ISD 185 230 283 µA 6
Thermal shutdown Rising threshold TTSD 150 165 175 ℃ 6
Leakage current (outputs OUT1 to OUT4) ILEAKAGE 0.1 5 µA Outputs OUT1 to OUT4, VOUTx = 45 V, EN = L 7
Maximum current OUT1 to OUT4 IMAX 120 mA OUT1, OUT2, OUT3, OUT4, RISET = 20 kΩ 7
Output current accuracy IOUT -5 5 % IOUT = 100 mA 7
Output current matching IMATCH 1 5 % IOUT = 100 mA, PWM duty =100% 7
High comparator threshold VHIGH_COMP 5.6 6 7 V 7
PWM input frequency ƒPWM 100 20000 Hz 7
Minimum on/off time tON/OFF 0.5 µs 7
Input voltage (boost/SEPIC) VIN 4.5 40 V 7
Output voltage (boost/SEPIC) VOUT 6 45 V 7
Minimum switching frequency ƒSW_MIN 300 kHz Defined by RFSET resistor 7
Maximum switching frequency ƒSW_MAX 2200 kHz Defined by RFSET resistor 7
Minimum switch OFF time tOFF 55 ns ƒSW ≥ 1.15 MHz 7
SW current limit first triggered ISW_MAX 3.3 3.7 4.1 A 7
SW current limit ISW_LIM 3 3.35 3.7 A 7
FET RDSON RDSON 240 400 mΩ 7
External SYNC frequency fSYNC 300 2200 kHz 7
Input low level VDDIO/EN VIL 0.4 V 7
Input high level VDDIO/EN VIH 1.65 V 7
Input DC current VDDIO/EN IEN -1 5 30 µA 7
Input low level SYNC, PWM VIL 0.2 × VDDIO/EN 8
Input high level SYNC, PWM VIH 0.8 × VDDIO/EN 8
Input current SYNC, PWM II -1 1 µA 8
FAULT output low level VOL 0.3 0.5 V Pullup current 3 mA 8
VIN UVLO rising threshold minus falling threshold VUVLO_HYST 150 mV 6
Short circuit current ISHORT 50 mA 6
Current for external load IEXT 5 mA 6
FB threshold for BST_OVP fault VFB_OVP 2.3 V 6
Thermal shutdown rising minus falling threshold TTSD_HYS 20 ℃ 6
Low comparator threshold VLOW_COMP 0.9 V 7
Mid comparator threshold VMID_COMP 1.9 V 7
SW current limit first triggered period tSW_MAX 1.6 s 6
External SYNC on time tSYNC_ON 150 ns 7
External SYNC off time tSYNC_OFF 150 ns 7
Input transient current during VDDIO/EN powering up 1.2 mA 7
Junction-to-ambient thermal resistance (PWP HTSSOP) RθJA 44.2 °C/W PWP (HTSSOP) 20 pins 6

CAD (KiCad official)

  • Symbol: LP8869QPWPRQ1
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: lp8869qpwprq1-etched.step / lp8869qpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lp8869qpwprq1.step / lp8869qpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 4ed821b4063c8430, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF