Generated by kicad-footprint-generator · KiCad file format 20260206
LP8867CQPWPRQ1
Texas Instruments · LED Drivers · HTSSOP-20-EP
LP8867CQPWPRQ1 from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input power pin and pin for input voltage detection for OVP protection; VIN operating range is 4.5 V to 40 V. |
| 2 | LDO | power_out | Output of the internal LDO; connect a 1-μF decoupling capacitor between this pin and noise-free GND, placed as close to the chip as possible. |
| 3 | FSET | passive | DC-DC (boost or SEPIC) switching frequency setting resistor; a resistor from 24 kΩ to 219 kΩ must be connected between this pin and ground for normal operation. |
| 4 | VDDIO/EN | power_in | Enable input for the device as well as supply input (VDDIO) for digital pins. |
| 5 | FAULT | output | Open-drain fault signal output; if unused, the pin may be left floating. |
| 6 | SYNC | input | Input for synchronizing the DC-DC converter; if synchronization is not used, connect to GND to disable spread spectrum or to VDDIO/EN to enable spread spectrum. |
| 7 | PWM | input | PWM dimming input. |
| 8 | NC | unconnected | No connect. |
| 9 | GND | power_in | Ground. |
| 10 | ISET | passive | LED current setting resistor; a resistor from 20 kΩ to 129 kΩ must be connected between this pin and ground for normal operation. |
| 11 | GND | power_in | Ground. |
| 12 | OUT4 | output | Current sink output for the LP8867C-Q1; must be connected to GND if not used. |
| 13 | OUT3 | output | Current sink output; must be connected to GND if not used. |
| 14 | OUT2 | output | Current sink output; must be connected to GND if not used. |
| 15 | OUT1 | output | Current sink output; must be connected to GND if not used. |
| 16 | FB | input | DC-DC feedback input; must be connected to the middle of a resistor divider between VOUT and ground, with feedback resistor values greater than 5 kΩ. |
| 17 | PGND | power_in | DC-DC (boost or SEPIC) power ground. |
| 18 | SW | output | DC-DC (boost or SEPIC) switch pin. |
| 19 | NC | unconnected | No connect. |
| 20 | VIN | power_in | Input power pin and pin for input voltage detection for OVP protection; VIN operating range is 4.5 V to 40 V. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage on pins VIN, SD, SW, FB | -0.3 | 50 | V | 5 | |||
| Voltage on pins OUT1, OUT2, OUT3, OUT4 | -0.3 | 45 | V | 5 | |||
| Voltage on pins LDO, SYNC, FSET, ISET, PWM, VDDIO/EN, FAULT | -0.3 | 5.5 | V | 5 | |||
| Ambient temperature TA | TA | -40 | 125 | °C | 5 | ||
| Junction temperature TJ | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| ESD human-body model, all pins | V(ESD) | -2000 | 2000 | V | HBM per AEC Q100-002, all pins | 5 | |
| ESD charged-device model, all pins | V(ESD) | -500 | 500 | V | CDM per AEC Q100-011, all pins | 5 | |
| ESD charged-device model, corner pins 1, 10, 11, 20 | V(ESD) | -750 | 750 | V | CDM per AEC Q100-011, corner pins (1, 10, 11 and 20) | 5 | |
| VIN input voltage recommended range | VIN | 4.5 | 12 | 45 | V | 6 | |
| Voltage on pins SW | SW | 0 | 45 | V | 6 | ||
| Voltage on pins OUT1, OUT2, OUT3, OUT4 | OUTx | 0 | 40 | V | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 44.2 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJCtop | 26.5 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 22.4 | °C/W | 6 | |||
| Junction-to-top characterization parameter | ψJT | 0.9 | °C/W | 6 | |||
| Junction-to-board characterization parameter | ψJB | 22.2 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJCbot | 2.5 | °C/W | 6 | |||
| Standby supply current | IQ | 4.5 | 20 | µA | Device disabled, VVDDIO/EN = 0 V, VIN = 12 V | 7 | |
| Active supply current | IQ | 5 | 12 | mA | VIN = 12 V, VOUT = 26 V, output current 80 mA/channel, converter ƒSW = 300 kHz | 7 | |
| Output current accuracy | IOUT | -5 | 5 | % | IOUT = 100 mA | 8 | |
| Output current matching | IMATCH | 1 | 5 | % | IOUT = 100 mA, PWM duty = 100% | 8 | |
| Input voltage | VIN | 4.5 | 40 | V | 8 | ||
| FET RDSON | RDSON | 240 | 400 | mΩ | 8 | ||
| Input DC current, VDDIO/EN | IEN | -1 | 5 | 30 | µA | 8 | |
| Input current, SYNC/PWM | II | -1 | 1 | µA | 8 | ||
| Output low level, FAULT | VOL | 0.3 | 0.5 | V | Pullup current 3 mA | 8 | |
| External load current | IEXT | 5 | mA | 7 | |||
| VIN UVLO hysteresis | VUVLO_HYST | 150 | mV | VIN UVLO rising threshold minus falling threshold | 7 | ||
| Thermal shutdown hysteresis | TTSD_HYS | 20 | °C | 7 | |||
| Minimum on/off time | tON/OFF | 0.5 | µs | 8 | |||
| Input high level, VDDIO/EN | VIH | 1.65 | V | 7 | |||
| Input transient current during VDDIO/EN powering up | 1.2 | mA | 7 | ||||
| Output leakage current, FAULT | ILEAKAGE | 1 | µA | V = 5.5 V | 8 |
CAD (KiCad official)
- Symbol:
LP8867CQPWPRQ1 - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP (KiCad packages3D, STEP)
- 3D model files:
lp8867cqpwprq1-etched.step/lp8867cqpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp8867cqpwprq1.step/lp8867cqpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (39 pp, sha256
4edba480f15843ca, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).