Generated by kicad-footprint-generator · KiCad file format 20260206
LP87702KRHBT
Texas Instruments · Power Management Specialized - PMIC · VQFN-32-EP(5x5)
LP87702KRHBT from Texas Instruments, in a VQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | nINT | output | Open-drain interrupt output, active LOW. |
| 2 | FB_B0 | input | Output voltage feedback input for Buck0. |
| 3 | FB_B1 | input | Output voltage feedback input for Buck1. |
| 4 | AGND | power_in | Analog ground. |
| 5 | VANA | power_in | Supply voltage for analog and digital blocks, which must be connected to the same node as VIN_Bx; recommended range 2.8 V to 5.5 V. |
| 6 | WD_RESET | output | Reset output from the window watchdog, with logic levels up to VANA. |
| 7 | WDI | input | Digital input signal for the window watchdog, with logic levels up to VANA. |
| 8 | VOUT_BST | power_out | Boost converter output, rated to 6 V absolute maximum. |
| 9 | SW_BST | input | Boost input, rated 2.8 V to 5.5 V in recommended operation. |
| 10 | PGND_BST | power_in | Power ground for the boost converter. |
| 11 | NRST | input | Reset signal input for the device, with logic levels from 0 V to 5.5 V. |
| 12 | GPO0 | output | General purpose digital output 0, configurable as push-pull (VANA level) or open-drain. |
| 13 | VIN_B1 | power_in | Input for Buck1; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 14 | VIN_B1 | power_in | Input for Buck1; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 15 | SW_B1 | output | Buck1 switch node. |
| 16 | SW_B1 | output | Buck1 switch node. |
| 17 | PGND_B1 | power_in | Power ground for Buck1. |
| 18 | PGND_B1 | power_in | Power ground for Buck1. |
| 19 | EN1 | input | Programmable enable 1 signal. |
| 20 | SCL | input | Serial interface clock input for I2C access, requires a pullup resistor; alternative function is programmable as enable 2. |
| 21 | SDA | bidirectional | Serial interface data input and output for I2C access, requires a pullup resistor; alternative function is programmable as enable 3. |
| 22 | CLKIN | bidirectional | External clock input for synchronization; alternative function is general purpose digital output 2 (GPO2). |
| 23 | PGND_B0 | power_in | Power ground for Buck0. |
| 24 | PGND_B0 | power_in | Power ground for Buck0. |
| 25 | SW_B0 | output | Buck0 switch node. |
| 26 | SW_B0 | output | Buck0 switch node. |
| 27 | VIN_B0 | power_in | Input for Buck0; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 28 | VIN_B0 | power_in | Input for Buck0; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 29 | PG0 | output | Programmable power-good indication signal. |
| 30 | VMON1 | input | Voltage monitoring input 1, rated 0 V to 5.5 V. |
| 31 | VMON2 | input | Voltage monitoring input 2, rated 0 V to 5.5 V. |
| 32 | PG1 | output | Programmable power-good indication signal; alternative function is general purpose digital output 1 (GPO1). |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-32-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage on input power connections (VIN_B0, VIN_B1, SW_BST, VANA) | -0.3 | 6 | V | 5 | |||
| Voltage on buck switch nodes (SW_B0, SW_B1) | -0.3 | V | max (VIN_Bx + 0.3 V) with 6-V maximum | 5 | |||
| Voltage on boost output (VOUT_BST) | -0.3 | 6 | V | 5 | |||
| Voltage on logic pins (NRST, EN1, nINT) | -0.3 | 6 | V | input or output pins | 5 | ||
| Junction temperature TJ-MAX | TJ-MAX | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Maximum lead temperature | 260 | °C | soldering, 10 sec | 5 | |||
| Input voltage on input power connections (VIN_B0, VIN_B1, VANA) | 2.8 | 5.5 | V | 5 | |||
| Voltage on voltage monitoring pins (VMON1, VMON2) | 0 | 5.5 | V | 5 | |||
| Voltage on logic pins (NRST, EN1, EN2, EN3, nINT) | 0 | 5.5 | V | 5 | |||
| Voltage on I2C interface SCL, SDA | 0 | 1.95 | V | High-speed mode (also Standard, Fast, Fast+) | 5 | ||
| Voltage on I2C interface SCL, SDA | 0 | V | Standard, Fast, Fast+ modes; VANA with 3.6-V maximum | 5 | |||
| Junction temperature | TJ | -40 | 140 | °C | 5 | ||
| Ambient temperature | TA | -40 | 125 | °C | 6 | ||
| Input voltage range | V(VIN_Bx), V(VANA) | 2.8 | 3.3 | 5.5 | V | 6 | |
| Output voltage programmable range | VOUT_Bx | 0.7 | 1 | 3.36 | V | 6 | |
| Output current | IOUT_Bx | 3.5 | A | Output current | 6 | ||
| DC output voltage accuracy | VOUT_Bx | -20 | 20 | mV | Force PWM mode, VOUT < 1.0 V | 7 | |
| DC output voltage accuracy | VOUT_Bx | -2 | 2 | % | Force PWM mode, VOUT ≥ 1.0 V | 7 | |
| DC output voltage accuracy | VOUT_Bx | -20 | 40 | mV | PFM mode, VOUT < 1.0 V, average output voltage level increased by max. 20 mV | 7 | |
| DC line regulation | DCLNR | -0.05 | 0.05 | %/V | IOUT = IOUT(max) | 7 | |
| Transient load step response | TLDSR | -65 | 65 | mV | IOUT = 0 A to 3 A, TR = TF = 1 µs, PWM mode, VVIN_Bx = 3.3V, VOUT_Bx = 1.2 V, COUT = 22 + 22 µF, L = 0.47 µH, fSW = 4 MHz | 7 | |
| Transient line response | TLNSR | -20 | 20 | mV | V(VIN_Bx) stepping 3 V ↔ 3.5 V, TR = TF = 10 µs, IOUT = IOUT(max) | 7 | |
| Forward current limit programmable range | ILIM FWD | 1.5 | 4.5 | A | Programmable range, both bucks | 7 | |
| Forward current limit accuracy | ILIM FWD | -5 | 7.5 | 20 | % | V(VIN_Bx) ≥ 3 V, ILIM = 4 A | 7 |
| Forward current limit accuracy | ILIM FWD | -20 | 7.5 | 20 | % | 2.8 V ≤ V(VIN_Bx) < 3 V, ILIM = 4 A | 7 |
| Negative current limit | ILIM NEG | 1.6 | 2 | 3 | A | 7 | |
| On-resistance, high-side FET (buck) | RDS(ON) BUCK HS FET | 60 | 110 | mΩ | Each phase, between VIN_Bx and SW_Bx pins (I = 1.0 A) | 7 | |
| On-resistance, low-side FET (buck) | RDS(ON) BUCK LS FET | 55 | 80 | mΩ | Each phase, between SW_Bx and PGND_Bx pins (I = 1.0 A) | 7 | |
| Switching frequency, PWM mode, 2-MHz setting | ƒSW | 1.8 | 2 | 2.2 | MHz | OTP programmable; 2-MHz setting or VOUT_Bx < 0.8 V | 7 |
| Switching frequency, PWM mode, 3-MHz setting | ƒSW | 2.7 | 3 | 3.3 | MHz | 3-MHz setting and VOUT_Bx ≥ 0.8 V | 7 |
| Switching frequency, PWM mode, 4-MHz setting | ƒSW | 3.6 | 4 | 4.4 | MHz | 4-MHz setting and VOUT_Bx ≥ 1.1 V | 7 |
| Output voltage slew rate, SLEW_RATEx=010 | -15 | 10 | 15 | mV/µs | SLEW_RATEx[2:0] = 010, VVOUT_Bx ≥ 0.7 V | 7 | |
| Output voltage slew rate, SLEW_RATEx=111 | -15 | 0.47 | 15 | mV/µs | SLEW_RATEx[2:0] = 111, VVOUT_Bx ≥ 0.7 V | 7 | |
| Output pull-down resistance (buck, converter disabled) | 75 | 125 | 175 | Ω | Converter disabled | 8 | |
| Input voltage range for boost power inputs | VIN_BST | 2.8 | 3.3 | 4 | V | 8 | |
| Input voltage range when bypass switch mode selected | 4.5 | 5.5 | V | 8 | |||
| Output current | IOUT_BST | 0.6 | A | Both boost and bypass mode | 8 | ||
| Output current limit | ILIM_BST | 0.8 | 1 | 1.3 | A | BOOST_ILIM = 00, VIN_BST < 3.6 V | 8 |
| Output current limit | ILIM_BST | 1.1 | 1.4 | 1.9 | A | BOOST_ILIM = 01, VIN_BST < 3.6 V | 8 |
| Output current limit | ILIM_BST | 1.5 | 1.9 | 2.3 | A | BOOST_ILIM = 10, VIN_BST < 3.6 V | 8 |
| Output current limit | ILIM_BST | 2.2 | 2.8 | 3.4 | A | BOOST_ILIM = 11, VIN_BST < 3.6 V | 8 |
| DC output voltage accuracy, boost mode | VOUT_BST_DC | -3 | 3 | % | Default output voltage | 8 | |
| Transient load step response, boost mode | TLDSR | -220 | 220 | mV | IOUT = 1 mA to 250 mA, TR = TF = 1 µs, 22 µF effective output capacitance, VIN > 3 V | 8 | |
| On-resistance, high-side FET (boost) | RDS(ON) BST HS FET | 145 | 220 | mΩ | Pin-to-pin, between SW_BST and VOUT_BST pins (I = 250 mA) | 8 | |
| On-resistance, low-side FET (boost) | RDS(ON) BST LS FET | 90 | 175 | mΩ | Pin-to-pin, between SW_BST and PGND_BST pins (I = 250 mA) | 8 | |
| Switching frequency, boost mode, 2-MHz setting | ƒSW | 1.8 | 2 | 2.2 | MHz | 2-MHz setting | 8 |
| Switching frequency, boost mode, 4-MHz setting | ƒSW | 3.6 | 4 | 4.4 | MHz | 4-MHz setting | 8 |
| Output voltage, boost mode, BOOST_VSET=00 | VOUT_BST | 4.9 | V | BOOST_VSET = 00 | 8 | ||
| Output voltage, boost mode, BOOST_VSET=01 | VOUT_BST | 5 | V | BOOST_VSET = 01 | 8 | ||
| Output voltage, boost mode, BOOST_VSET=10 | VOUT_BST | 5.1 | V | BOOST_VSET = 10 | 8 | ||
| Output voltage, boost mode, BOOST_VSET=11 | VOUT_BST | 5.2 | V | BOOST_VSET = 11 | 8 | ||
| DC load regulation in PWM mode | DCLDR | 0.3 | % | VOUT_Bx = 1.0 V, IOUT from 0 to IOUT(max) | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 31.7 | °C/W | RHB (VQFN), 32 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJCtop | 17.1 | °C/W | RHB (VQFN), 32 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 5.6 | °C/W | RHB (VQFN), 32 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJCbot | 1.1 | °C/W | RHB (VQFN), 32 pins | 6 | ||
| Start-up time (soft start) | 120 | µs | From ENx to VOUT_Bx = 0.35 V (slew-rate control begins) | 7 |
CAD (KiCad official)
- Symbol:
LP87702KRHBT - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: VQFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
lp87702krhbt-etched.step/lp87702krhbt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp87702krhbt.step/lp87702krhbt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (98 pp, sha256
8bf7adfb89ee13a9, retrieved 2026-11-02, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).