Generated by kicad-footprint-generator · KiCad file format 20260206
LP87332DRHDRQ1
Texas Instruments · Linear Voltage Regulators (LDO) · VQFN-28-EP(5x5)
LP87332DRHDRQ1 from Texas Instruments, in a VQFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT_LDO0 | power_out | LDO0 output; leave floating if LDO0 is not used. |
| 2 | FB_B0 | input | Positive output voltage feedback for Buck 0. |
| 3 | FB_B1 | input | Positive output voltage feedback for Buck 1. |
| 4 | AGND | power_in | Analog ground. |
| 5 | VANA | power_in | Supply voltage for analog and digital blocks; must be connected to the same node as VIN_Bx. |
| 6 | EN | input | Programmable enable signal for regulators and GPOs; leave floating if not used. |
| 7 | VOUT_LDO1 | power_out | LDO1 output; leave floating if LDO1 is not used. |
| 8 | VIN_LDO1 | power_in | Power input for LDO1; connect to VANA if LDO1 is not used. |
| 9 | nINT | output | Open-drain interrupt output, active LOW; connect to ground if not used. |
| 10 | CLKIN | bidirectional | External clock input, with alternative function GPO2 general-purpose digital output; leave floating if not used. |
| 11 | VIN_B1 | power_in | Input for Buck 1; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 12 | VIN_B1 | power_in | Input for Buck 1; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 13 | SW_B1 | power_out | Buck 1 switch node; leave floating if Buck 1 is not used. |
| 14 | SW_B1 | power_out | Buck 1 switch node; leave floating if Buck 1 is not used. |
| 15 | PGND_B1 | power_in | Power ground for Buck 1. |
| 16 | PGND_B1 | power_in | Power ground for Buck 1. |
| 17 | SCL | input | Serial interface clock input for I2C access; connect a pullup resistor, or connect to ground if I2C is not used. |
| 18 | SDA | bidirectional | Serial interface data input and output for I2C access; connect a pullup resistor, or connect to ground if I2C is not used. |
| 19 | SGND | power_in | Ground. |
| 20 | PGND_B0 | power_in | Power ground for Buck 0. |
| 21 | PGND_B0 | power_in | Power ground for Buck 0. |
| 22 | SW_B0 | power_out | Buck 0 switch node; leave floating if Buck 0 is not used. |
| 23 | SW_B0 | power_out | Buck 0 switch node; leave floating if Buck 0 is not used. |
| 24 | VIN_B0 | power_in | Input for Buck 0; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 25 | VIN_B0 | power_in | Input for Buck 0; VIN_Bx pins must be connected together in the application and locally bypassed. |
| 26 | GPO | output | General-purpose digital output; leave floating if not used. |
| 27 | PGOOD | output | Power-good indication signal; leave floating if not used. |
| 28 | VIN_LDO0 | power_in | Power input for LDO0; connect to VANA if LDO0 is not used. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-28-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage on power connections VIN_Bx, VANA | -0.3 | 6 | V | Must use the same input supply | 5 | ||
| Voltage on power connections VIN_LDOx | -0.3 | 6 | V | 5 | |||
| Junction temperature | TJ-MAX | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage range VIN_Bx, VANA (recommended) | 2.8 | 5.5 | V | Must use the same input supply | 5 | ||
| Input voltage range VIN_LDOx (recommended) | 2.5 | 5.5 | V | Voltage on LDO inputs | 5 | ||
| Junction temperature (recommended) | TJ | -40 | 140 | °C | 5 | ||
| Ambient temperature (recommended) | TA | -40 | 125 | °C | 5 | ||
| Input voltage range for buck regulators | V(VIN_Bx), V(VANA) | 2.8 | 3.7 | 5.5 | V | VIN_Bx and VANA pins must be connected to the same supply line | 6 |
| DC output voltage accuracy, buck (Force PWM, VOUT ≥ 1 V) | VOUT_Bx_DC | -2 | 2 | % | Force PWM mode, VOUT ≥ 1 V | 7 | |
| DC output voltage accuracy, buck (Force PWM, VOUT < 1 V) | VOUT_Bx_DC | -20 | 20 | mV | Force PWM mode, VOUT < 1 V | 7 | |
| DC output voltage accuracy, buck (PFM, VOUT < 1 V) | VOUT_Bx_DC | -20 | 40 | mV | PFM mode, VOUT < 1 V, the average output voltage level is increased by max. 20 mV | 7 | |
| Forward current limit per phase, programmable range | ILIM FWD | 1.5 | 4 | A | Peak for every switching cycle | 7 | |
| Negative current limit per phase | ILIM NEG | 1.6 | 2 | 3 | A | 7 | |
| Output current, buck | IOUT_Bx | 3 | A | Output current | 6 | ||
| On-resistance, high-side FET | RDS(ON) HS FET | 50 | 110 | mΩ | Each phase, between VIN_Bx and SW_Bx pins (I = 1 A) | 7 | |
| On-resistance, low-side FET | RDS(ON) LS FET | 45 | 90 | mΩ | Each phase, between SW_Bx and PGND_Bx pins (I = 1 A) | 7 | |
| Switching frequency | ƒSW | 1.8 | 2 | 2.2 | MHz | PWM mode | 7 |
| Output pulldown resistance, buck | RDIS_Bx | 150 | 250 | 350 | Ω | Regulator disabled | 7 |
| Thermal warning (TDIE_WARN_LEVEL = 0) | 115 | 125 | 135 | °C | Temperature rising, TDIE_WARN_LEVEL = 0 | 9 | |
| Thermal shutdown | 140 | 150 | 160 | °C | Temperature rising | 9 | |
| VANA overvoltage threshold | VANAOVP | 5.6 | 5.8 | 6.1 | V | Voltage rising | 9 |
| VANA undervoltage lockout threshold | VANAUVLO | 2.51 | 2.63 | 2.75 | V | Voltage rising | 9 |
| Digital input low level | VIL | 0.4 | V | EN, SCL, SDA, CLKIN | 10 | ||
| Digital input high level | VIH | 1.2 | V | EN, SCL, SDA, CLKIN | 10 | ||
| Output low level, nINT | VOL | 0.4 | V | nINT: ISOURCE = 2 mA | 10 | ||
| Input current, all logic inputs | ILEAK | -1 | 1 | µA | All logic inputs over pin voltage range | 10 | |
| Input voltage range for LDO power inputs | VIN_LDOx | 2.5 | 3.7 | 5.5 | V | VIN_LDOx can be higher or lower than V(VANA) | 8 |
| LDO output voltage, programmable range | VOUT_LDOx | 0.8 | 3.3 | V | Programmable voltage range | 8 | |
| LDO output current | IOUT_LDOx | 300 | mA | Output current | 8 | ||
| Dropout voltage, LDO | 200 | mV | V(VIN_LDOx), V(VOUT_LDOx), IOUT = IOUT(max), programmed output voltage is higher than V(VIN_LDOx) | 8 | |||
| LDO current limit | ISHORT(LDOx) | 400 | 500 | 600 | mA | VOUT = 0 V | 8 |
| DC output voltage accuracy, LDO (VOUT ≥ 1 V) | VOUT_LDO_DC | -2 | 2 | % | VOUT ≥ 1 V | 8 | |
| DC output voltage accuracy, LDO (VOUT < 1 V) | VOUT_LDO_DC | -20 | 20 | mV | VOUT < 1 V | 8 | |
| External input clock frequency | fEXT_CLK | 1 | 24 | MHz | Nominal frequency | 9 | |
| Inductor tolerance | L | -30 | 30 | % | Inductance of the inductor | 6 | |
| Inductance (recommended inductor) | L | 0.47 | µH | Inductance of the inductor | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 36.7 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJCtop | 26.6 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 8.9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJCbot | 2.2 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LP87332DRHDRQ1 - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: VQFN-28-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
lp87332drhdrq1-etched.step/lp87332drhdrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp87332drhdrq1.step/lp87332drhdrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (79 pp, sha256
d55510b939770f4c, retrieved 2026-10-28, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).