main
Ray
Publish 0.1.0
46a65f4
LP8556SQE-E08
Texas Instruments · LED Drivers · WQFN-24-EP(4x4)
LP8556SQE-E08 from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | passive | Connection to the drain terminal of the integrated power MOSFET; absolute maximum voltage on SW is -0.3 V to 50 V. |
| 2 | SW | passive | Connection to the drain terminal of the integrated power MOSFET; absolute maximum voltage on SW is -0.3 V to 50 V. |
| 3 | GND_SW | power_in | Connection to the source terminal of the integrated power MOSFET, to be tied to ground. |
| 4 | GND_SW | power_in | Connection to the source terminal of the integrated power MOSFET, to be tied to ground. |
| 5 | SDA | bidirectional | I2C data input/output pin; absolute maximum voltage on logic pins (SCL, SDA, PWM) is -0.3 V to 6 V. |
| 6 | SCL | input | I2C clock input pin; absolute maximum voltage on logic pins (SCL, SDA, PWM) is -0.3 V to 6 V. |
| 7 | EN / VDDIO | power_in | Dual-purpose chip enable and power supply reference for PWM, SDA and SCL inputs; recommended range 1.62 V to 3.6 V, driven by a logic gate capable of sourcing at least 1 mA. |
| 8 | NC | unconnected | No connect pin. |
| 9 | PWM | input | PWM dimming input accepting a 75-Hz to 25-kHz PWM signal; must be connected to GND if unused. |
| 10 | GND | power_in | Ground pin. |
| 11 | GND | power_in | Ground pin. |
| 12 | LED1 | passive | LED driver current sink terminal; may be left floating if unused. |
| 13 | LED2 | passive | LED driver current sink pin; may be left floating if unused. |
| 14 | LED3 | passive | LED driver current sink terminal; may be left floating if unused. |
| 15 | GND | power_in | Ground pin. |
| 16 | LED4 | passive | LED driver current sink pin; may be left floating if unused. |
| 17 | LED5 | passive | LED driver current sink pin; may be left floating if unused. |
| 18 | LED6 | passive | LED driver current sink pin; may be left floating if unused. |
| 19 | VLDO | power_out | Internal LDO output pin; connect capacitor CVLDO between this pin and ground. |
| 20 | VBOOST | power_out | Boost converter output monitored by the internal FB and OVP circuitry; connect the output capacitor bank close to this pin. Absolute maximum rating is -0.3 V to 50 V. |
| 21 | FSET | passive | Connect resistor RFSET to ground to set boost and PWM output dimming frequency; may be left floating only if PWM_FSET_EN = 0 and BOOST_FSET_EN = 0. |
| 22 | VDD | power_in | Device power supply pin requiring 2.7 V to 20 V; input of the internal LDO that powers the device. |
| 23 | ISET | passive | Connect LED current set resistor RISET to ground; may be left floating if ISET_EN = 0. |
| 24 | GND | power_in | Ground pin. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage | VDD | -0.3 | 24 | V | 6 | ||
| Voltage on logic pins (SCL, SDA, PWM) | -0.3 | 6 | V | 6 | |||
| Voltage on analog pins (VLDO, EN / VDDIO) | -0.3 | 6 | V | 6 | |||
| Voltage on analog pins (FSET, ISET) | -0.3 | V | 6 | ||||
| Voltage on LED1...LED6, SW, VBOOST | -0.3 | 50 | V | 6 | |||
| Junction temperature (TJ-MAX) | TJ-MAX | 125 | °C | 6 | |||
| Maximum lead temperature (soldering) | 260 | °C | 6 | ||||
| Storage temperature | Tstg | -65 | 150 | °C | 6 | ||
| VDD supply voltage | VDD | 2.7 | 20 | V | 6 | ||
| EN / VDDIO supply voltage | 1.62 | 3.6 | V | 6 | |||
| Voltage on LED1...LED6, SW, VBOOST | 0 | 48 | V | 6 | |||
| Junction temperature | TJ | -30 | 125 | °C | 6 | ||
| Ambient temperature | TA | -30 | 85 | °C | 6 | ||
| Input voltage for the internal LDO | VDD | 2.7 | 20 | V | 7 | ||
| Supply voltage for digital I/Os | VDDIO | 1.62 | 3.6 | V | 7 | ||
| Standby supply current | IDD | 1.6 | µA | EN / VDDIO = 0 V, LDO disabled, -30°C ≤ TA ≤ 85°C | 7 | ||
| Normal mode supply current | IDD | 0.9 | 1.5 | mA | LDO enabled, boost disabled | 7 | |
| Normal mode supply current | IDD | 2.2 | 3.65 | mA | LDO enabled, boost enabled, no load | 7 | |
| Internal oscillator frequency accuracy | fOSC | -4 | 4 | % | 7 | ||
| Internal oscillator frequency accuracy | fOSC | -7 | 7 | % | -30°C ≤ TA ≤ 85°C | 7 | |
| LDO output voltage | VLDO | 2.95 | 3.05 | 3.15 | V | VDD ≥ 3.1 V | 7 |
| Boost minimum output voltage | VBOOST_MIN | 7 | V | VBOOST_RANGE = 0 | 8 | ||
| Boost minimum output voltage | VBOOST_MIN | 16 | V | VBOOST_RANGE = 1 | 8 | ||
| Boost maximum output voltage | VBOOST_MAX | 19 | 21 | 22 | V | VBOOST_MAX = 100, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 24 | 25 | 27 | V | VBOOST_MAX = 101, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 28 | 30 | 32 | V | VBOOST_MAX = 110, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 32 | 34 | 37 | V | VBOOST_MAX = 111, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 17.9 | 21 | 23.1 | V | VBOOST_MAX = 010, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 22.8 | 25 | 27.2 | V | VBOOST_MAX = 011, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 27.8 | 30 | 31.5 | V | VBOOST_MAX = 100, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 32.7 | 34.5 | 36.6 | V | VBOOST_MAX = 101, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 37.2 | 39 | 40.8 | V | VBOOST_MAX = 110, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 41.8 | 43 | 44.2 | V | VBOOST_MAX = 111, VBOOST_RANGE = 1 | 8 |
| Maximum continuous output load current | ILOAD_MAX | 220 | mA | VIN = 3 V, VOUT = 18 V | 8 | ||
| Maximum continuous output load current | ILOAD_MAX | 160 | mA | VIN = 3 V, VOUT = 24 V | 8 | ||
| Maximum continuous output load current | ILOAD_MAX | 120 | mA | VIN = 3 V, VOUT = 30 V | 8 | ||
| SW pin current limit | ISW_LIM | 0.66 | 0.9 | 1.16 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 00 | 8 |
| SW pin current limit | ISW_LIM | 0.88 | 1.2 | 1.4 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 01 | 8 |
| SW pin current limit | ISW_LIM | 1.12 | 1.5 | 1.73 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 10 | 8 |
| SW pin current limit | ISW_LIM | 1.35 | 1.8 | 2.07 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 11 | 8 |
| Leakage current | ILED_LEAKAGE | 0.1 | 1 | µA | Outputs LED1...LED6, VOUT = 48 V | 9 | |
| Maximum sink current | ILED_MAX | 50 | mA | LED1...LED6 | 9 | ||
| LED current accuracy | ILED | -3 | 1 | 3 | % | Output current set to 23 mA | 9 |
| LED current accuracy | ILED | -4 | 1 | 4 | % | Output current set to 23 mA, -30°C ≤ TA ≤ 85°C | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.02 | 100 | % | 100 Hz < fPWM ≤ 200 Hz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.04 | 100 | % | 1 kHz < fPWM ≤ 2 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.1 | 100 | % | 2 kHz < fPWM ≤ 5 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.2 | 100 | % | 5 kHz < fPWM ≤ 10 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.4 | 100 | % | 10 kHz < fPWM ≤ 20 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.6 | 100 | % | 20 kHz < fPWM ≤ 30 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.8 | 100 | % | 30 kHz < fPWM ≤ 39 kHz | 9 | |
| PWM frequency range | fPWM | 75 | 25000 | Hz | 9 | ||
| Minimum pulse ON time | tMIN_ON | 1 | µs | 9 | |||
| Minimum pulse OFF time | tMIN_OFF | 1 | µs | 9 | |||
| Input current (logic inputs PWM, SDA, SCL) | II | -1 | 1 | µA | VDDIO = 0 V or 3.6 V, VI = 0 V or 3.6 V, -30°C ≤ TA ≤ 85°C | 10 | |
| Output low level (SDA) | VOL | 0.3 | V | IOUT = 3 mA (pull-up current) | 10 | ||
| Output low level (SDA) | VOL | 0.3 | 0.4 | V | IOUT = 3 mA (pull-up current), -30°C ≤ TA ≤ 85°C | 10 | |
| Output leakage current (SDA) | IL | -1 | 1 | µA | VOUT = 5 V, -30°C ≤ TA ≤ 85°C | 10 |
CAD (KiCad official)
- Symbol:
LP8556SQE-E08 - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lp8556sqe-e08-etched.step/lp8556sqe-e08-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp8556sqe-e08.step/lp8556sqe-e08.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (65 pp, sha256
13ca3211bd8fa7b8, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LP8556SQE-E08
**Texas Instruments** · LED Drivers · WQFN-24-EP(4x4)
LP8556SQE-E08 from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | passive | Connection to the drain terminal of the integrated power MOSFET; absolute maximum voltage on SW is -0.3 V to 50 V. |
| 2 | SW | passive | Connection to the drain terminal of the integrated power MOSFET; absolute maximum voltage on SW is -0.3 V to 50 V. |
| 3 | GND_SW | power_in | Connection to the source terminal of the integrated power MOSFET, to be tied to ground. |
| 4 | GND_SW | power_in | Connection to the source terminal of the integrated power MOSFET, to be tied to ground. |
| 5 | SDA | bidirectional | I2C data input/output pin; absolute maximum voltage on logic pins (SCL, SDA, PWM) is -0.3 V to 6 V. |
| 6 | SCL | input | I2C clock input pin; absolute maximum voltage on logic pins (SCL, SDA, PWM) is -0.3 V to 6 V. |
| 7 | EN / VDDIO | power_in | Dual-purpose chip enable and power supply reference for PWM, SDA and SCL inputs; recommended range 1.62 V to 3.6 V, driven by a logic gate capable of sourcing at least 1 mA. |
| 8 | NC | unconnected | No connect pin. |
| 9 | PWM | input | PWM dimming input accepting a 75-Hz to 25-kHz PWM signal; must be connected to GND if unused. |
| 10 | GND | power_in | Ground pin. |
| 11 | GND | power_in | Ground pin. |
| 12 | LED1 | passive | LED driver current sink terminal; may be left floating if unused. |
| 13 | LED2 | passive | LED driver current sink pin; may be left floating if unused. |
| 14 | LED3 | passive | LED driver current sink terminal; may be left floating if unused. |
| 15 | GND | power_in | Ground pin. |
| 16 | LED4 | passive | LED driver current sink pin; may be left floating if unused. |
| 17 | LED5 | passive | LED driver current sink pin; may be left floating if unused. |
| 18 | LED6 | passive | LED driver current sink pin; may be left floating if unused. |
| 19 | VLDO | power_out | Internal LDO output pin; connect capacitor CVLDO between this pin and ground. |
| 20 | VBOOST | power_out | Boost converter output monitored by the internal FB and OVP circuitry; connect the output capacitor bank close to this pin. Absolute maximum rating is -0.3 V to 50 V. |
| 21 | FSET | passive | Connect resistor RFSET to ground to set boost and PWM output dimming frequency; may be left floating only if PWM_FSET_EN = 0 and BOOST_FSET_EN = 0. |
| 22 | VDD | power_in | Device power supply pin requiring 2.7 V to 20 V; input of the internal LDO that powers the device. |
| 23 | ISET | passive | Connect LED current set resistor RISET to ground; may be left floating if ISET_EN = 0. |
| 24 | GND | power_in | Ground pin. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage | VDD | -0.3 | | 24 | V | | 6 |
| Voltage on logic pins (SCL, SDA, PWM) | | -0.3 | | 6 | V | | 6 |
| Voltage on analog pins (VLDO, EN / VDDIO) | | -0.3 | | 6 | V | | 6 |
| Voltage on analog pins (FSET, ISET) | | -0.3 | | | V | | 6 |
| Voltage on LED1...LED6, SW, VBOOST | | -0.3 | | 50 | V | | 6 |
| Junction temperature (TJ-MAX) | TJ-MAX | | | 125 | °C | | 6 |
| Maximum lead temperature (soldering) | | | | 260 | °C | | 6 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 6 |
| VDD supply voltage | VDD | 2.7 | | 20 | V | | 6 |
| EN / VDDIO supply voltage | | 1.62 | | 3.6 | V | | 6 |
| Voltage on LED1...LED6, SW, VBOOST | | 0 | | 48 | V | | 6 |
| Junction temperature | TJ | -30 | | 125 | °C | | 6 |
| Ambient temperature | TA | -30 | | 85 | °C | | 6 |
| Input voltage for the internal LDO | VDD | 2.7 | | 20 | V | | 7 |
| Supply voltage for digital I/Os | VDDIO | 1.62 | | 3.6 | V | | 7 |
| Standby supply current | IDD | | | 1.6 | µA | EN / VDDIO = 0 V, LDO disabled, -30°C ≤ TA ≤ 85°C | 7 |
| Normal mode supply current | IDD | | 0.9 | 1.5 | mA | LDO enabled, boost disabled | 7 |
| Normal mode supply current | IDD | | 2.2 | 3.65 | mA | LDO enabled, boost enabled, no load | 7 |
| Internal oscillator frequency accuracy | fOSC | -4 | | 4 | % | | 7 |
| Internal oscillator frequency accuracy | fOSC | -7 | | 7 | % | -30°C ≤ TA ≤ 85°C | 7 |
| LDO output voltage | VLDO | 2.95 | 3.05 | 3.15 | V | VDD ≥ 3.1 V | 7 |
| Boost minimum output voltage | VBOOST_MIN | 7 | | | V | VBOOST_RANGE = 0 | 8 |
| Boost minimum output voltage | VBOOST_MIN | 16 | | | V | VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 19 | 21 | 22 | V | VBOOST_MAX = 100, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 24 | 25 | 27 | V | VBOOST_MAX = 101, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 28 | 30 | 32 | V | VBOOST_MAX = 110, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 32 | 34 | 37 | V | VBOOST_MAX = 111, VBOOST_RANGE = 0 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 17.9 | 21 | 23.1 | V | VBOOST_MAX = 010, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 22.8 | 25 | 27.2 | V | VBOOST_MAX = 011, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 27.8 | 30 | 31.5 | V | VBOOST_MAX = 100, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 32.7 | 34.5 | 36.6 | V | VBOOST_MAX = 101, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 37.2 | 39 | 40.8 | V | VBOOST_MAX = 110, VBOOST_RANGE = 1 | 8 |
| Boost maximum output voltage | VBOOST_MAX | 41.8 | 43 | 44.2 | V | VBOOST_MAX = 111, VBOOST_RANGE = 1 | 8 |
| Maximum continuous output load current | ILOAD_MAX | | | 220 | mA | VIN = 3 V, VOUT = 18 V | 8 |
| Maximum continuous output load current | ILOAD_MAX | | | 160 | mA | VIN = 3 V, VOUT = 24 V | 8 |
| Maximum continuous output load current | ILOAD_MAX | | | 120 | mA | VIN = 3 V, VOUT = 30 V | 8 |
| SW pin current limit | ISW_LIM | 0.66 | 0.9 | 1.16 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 00 | 8 |
| SW pin current limit | ISW_LIM | 0.88 | 1.2 | 1.4 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 01 | 8 |
| SW pin current limit | ISW_LIM | 1.12 | 1.5 | 1.73 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 10 | 8 |
| SW pin current limit | ISW_LIM | 1.35 | 1.8 | 2.07 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 11 | 8 |
| Leakage current | ILED_LEAKAGE | | 0.1 | 1 | µA | Outputs LED1...LED6, VOUT = 48 V | 9 |
| Maximum sink current | ILED_MAX | | | 50 | mA | LED1...LED6 | 9 |
| LED current accuracy | ILED | -3 | 1 | 3 | % | Output current set to 23 mA | 9 |
| LED current accuracy | ILED | -4 | 1 | 4 | % | Output current set to 23 mA, -30°C ≤ TA ≤ 85°C | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.02 | | 100 | % | 100 Hz < fPWM ≤ 200 Hz | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.04 | | 100 | % | 1 kHz < fPWM ≤ 2 kHz | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.1 | | 100 | % | 2 kHz < fPWM ≤ 5 kHz | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.2 | | 100 | % | 5 kHz < fPWM ≤ 10 kHz | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.4 | | 100 | % | 10 kHz < fPWM ≤ 20 kHz | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.6 | | 100 | % | 20 kHz < fPWM ≤ 30 kHz | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.8 | | 100 | % | 30 kHz < fPWM ≤ 39 kHz | 9 |
| PWM frequency range | fPWM | 75 | | 25000 | Hz | | 9 |
| Minimum pulse ON time | tMIN_ON | 1 | | | µs | | 9 |
| Minimum pulse OFF time | tMIN_OFF | 1 | | | µs | | 9 |
| Input current (logic inputs PWM, SDA, SCL) | II | -1 | | 1 | µA | VDDIO = 0 V or 3.6 V, VI = 0 V or 3.6 V, -30°C ≤ TA ≤ 85°C | 10 |
| Output low level (SDA) | VOL | | | 0.3 | V | IOUT = 3 mA (pull-up current) | 10 |
| Output low level (SDA) | VOL | | 0.3 | 0.4 | V | IOUT = 3 mA (pull-up current), -30°C ≤ TA ≤ 85°C | 10 |
| Output leakage current (SDA) | IL | -1 | | 1 | µA | VOUT = 5 V, -30°C ≤ TA ≤ 85°C | 10 |
## CAD (KiCad official)
- Symbol: `LP8556SQE-E08`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `lp8556sqe-e08-etched.step` / `lp8556sqe-e08-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lp8556sqe-e08.step` / `lp8556sqe-e08.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lp8556sqe-e08.pdf) (65 pp, sha256 `13ca3211bd8fa7b8`, retrieved 2026-10-31, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lp8556sqe-e08-datasheet.pdf)