main
Ray Publish 0.1.0 c0b6dcc

LP5912Q3.0DRVRQ1

Texas Instruments · Linear Voltage Regulators (LDO) · WSON-6-EP(2x2)

LP5912Q3.0DRVRQ1 from Texas Instruments, in a WSON-6-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT power_out Regulated output voltage, 3.0 V fixed for this option, supporting up to 500 mA output current.
2 NC unconnected No internal connection; leave open or connect to ground.
3 PG output Open-drain power-good indicator that requires an external pullup (10 kΩ to 100 kΩ recommended), with 140 µs typical delay on the rising edge.
4 EN input Enable input: logic high turns the device ON and logic low turns it OFF, with an internal 3-MΩ pulldown to GND.
5 GND power_in Ground.
6 IN power_in Unregulated input voltage, 1.6 V to 6.5 V operating range.
7 EP passive Exposed thermal pad; connect to copper area with thermal vias to improve thermal performance, connect to ground or leave floating, and do not connect to any potential other than ground.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-6-EP(2x2)
Category Power Supply Chip
Pins 7

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN -0.3 7 V 4
Output voltage VOUT -0.3 7 V 4
Enable input voltage VEN -0.3 7 V 4
Power Good (PG) pin OFF voltage VPG -0.3 7 V 4
Junction temperature TJ 150 °C 4
Storage temperature Tstg -65 150 °C 4
Input supply voltage VIN 1.6 6.5 V 4
Output voltage VOUT 0.8 5.5 V 4
Enable input voltage VEN 0 V max = VIN 4
PG pin OFF voltage VPG 0 6.5 V 4
Output current IOUT 0 500 mA 4
Operating junction temperature TJ-MAX-OP -40 125 °C 4
Junction-to-ambient thermal resistance, High-K RθJA 71.2 °C/W DRV (WSON), 6 pins 4
Junction-to-case (top) thermal resistance RθJC(top) 93.7 °C/W 4
Junction-to-board thermal resistance RθJB 40.7 °C/W 4
Junction-to-case (bottom) thermal resistance ψJC(bot) 11.2 °C/W 4
Output voltage tolerance ΔVOUT -3 3 % For 1.1 V ≤ VOUT(NOM) < 3.3 V: VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.5 V, IOUT = 1 mA to 500 mA 5
Line regulation 0.8 %/V For VOUT(NOM) ≥ 1.1 V: VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.5 V 5
Load regulation 0.0022 %/mA IOUT = 1 mA to 500 mA 5
Short-circuit current limit ISC 700 900 1100 mA TJ = 25°C 5
Reverse leakage current IRO 10 150 µA VIN < VOUT 5
Quiescent current IQ 30 55 µA VEN = 1.3 V, IOUT = 0 mA 5
Quiescent current IQ 400 600 µA VEN = 1.3 V, IOUT = 500 mA 5
Quiescent current, shutdown mode IQ(SD) 0.2 1.5 µA VEN = 0 V, -40°C ≤ TJ ≤ 85°C 5
Quiescent current, shutdown mode IQ(SD) 0.2 5 µA VEN = 0 V 5
Ground current IG 35 µA VEN = 1.3 V, IOUT = 0 mA 5
Dropout voltage VDO 170 250 mV IOUT = 500 mA, 1.6 V ≤ VOUT(NOM) < 3.3 V 5
OFF threshold VEN(OFF) 0.3 V VIN = 1.6 V to 6.5 V, VEN falling until device is disabled 6
ON threshold VEN(ON) 1.3 V 1.6 V ≤ VIN ≤ 6.5 V, VEN rising until device is enabled 6
Input current at EN pin IEN 2.5 µA VEN = 6.5 V, VIN = 6.5 V 6
PG pin low-level output voltage VOL(PG) 100 mV VOUT < PGLTH, sink current = 1 mA 6
PG pin leakage current IlKG(PG) 1 µA VOUT < PGHTH, VPG = 6.5 V 6
PG high threshold (% of nominal VOUT) PGHTH 94 % 6
PG low threshold (% of nominal VOUT) PGLTH 90 % 6
PG delay time tPGD 140 µs Time from VOUT > PG threshold to PG toggling 6
Power Supply Rejection Ratio PSRR 75 dB ƒ = 1 kHz, VOUT ≥ 1.1 V, IOUT = 20 mA 6
Noise voltage eN 12 µVRMS IOUT = 1 mA, BW = 10 Hz to 100 kHz 6
Thermal shutdown temperature TSD 160 °C 6
Thermal shutdown hysteresis THYS 15 °C 6
Turnon time tON 200 µs From VEN > VEN(ON) to VOUT = 95% of VOUT(NOM) 7
Output discharge pulldown resistance RAD 100 Ω VEN = 0 V, VIN = 3.6 V 7
Input capacitance for stability CIN 0.7 1 µF Capacitance for stability 7
Output capacitance for stability COUT 0.7 1 10 µF Capacitance for stability 7
Output capacitor ESR ESR 5 500 mΩ 7

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper ground pin using as wide and as short of a copper trace as is practical. 24

CAD (KiCad official)

  • Symbol: LP5912Q3.0DRVRQ1
  • Footprint: Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm
  • 3D model: WSON-6-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: lp5912q3-0drvrq1-etched.step / lp5912q3-0drvrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lp5912q3-0drvrq1.step / lp5912q3-0drvrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (34 pp, sha256 6f09792344f18d7a, retrieved 2026-10-31, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF