Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LP5910-1.0DRVR

Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · WSON-6-EP(2x2)

LP5910-1.0DRVR from Texas Instruments, in a WSON-6-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT output Voltage output; 1-µF low-ESR capacitor must be connected from this pin to GND pin.
2 NC unconnected No internal connection; connect to ground or leave open.
3 NC unconnected No internal connection; connect to ground or leave open.
4 EN input Enable input; logic low disables regulator, logic high enables regulator; 1-MΩ internal pull-down resistor to ground.
5 GND power_in Common ground.
6 IN input Voltage supply input; 1-μF capacitor must be connected at this input.
7 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-6-EP(2x2)
Category Power Management (PMIC)
Pins 7

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN -0.3 3.6 V 4
Output voltage VOUT -0.3 3.6 V 4
Enable input voltage VEN -0.3 3.6 V 4
Junction temperature TJ(MAX) 150 °C 4
Storage temperature Tstg -65 150 °C 4
Input voltage VIN 1.3 3.3 V 4
Output voltage VOUT 0.8 2.3 V 4
Enable input voltage VEN 0 3.3 V 4
Output current IOUT 0 300 mA 4
Junction temperature TJ -40 125 °C 4
Ambient temperature TA -40 85 °C 4
Output capacitor capacitance for stability COUT 0.7 1 10 µF 15
Output capacitor ESR ESR 5 500 mΩ 15
Output voltage tolerance ΔVOUT -2 2 %VOUT VIN = (VOUT(NOM) + 0.5 V) to 3.3 V, IOUT = 1 mA to 300 mA 5
Load current ILOAD 0 300 mA See note (4) 5
Quiescent current IQ 12 25 µA VEN = 1 V, IOUT = 0 mA 5
Quiescent current IQ 230 350 µA VEN = 1 V, IOUT = 300 mA 5
Quiescent current in shutdown IQ(SD) 0.02 2 µA VEN = 0.3 V, –40°C ≤ TJ ≤ 85°C 5
Output reverse current IRO -20 0 µA VOUT > VIN; VOUT = 3.3 V, VIN = VEN = 0 V 5
Output reverse current IRO 0 50 µA VOUT > VIN; VOUT = 3.3 V, VIN = VEN = 1.3 V 5
Ground current IG 15 µA IOUT = 0 mA (VOUT = 2.3 V) 5
Output current limit ILIMIT 450 mA VOUT = VOUT(NOM) – 0.1 V, VIN = VOUT(NOM) + 0.5 V 5
Power supply rejection ratio PSRR 80 dB ƒ = 100 Hz, IOUT = 20 mA, VOUT ≥ 1 V 6
Power supply rejection ratio PSRR 75 dB ƒ = 1 kHz, IOUT = 20 mA, VOUT ≥ 1 V 6
Power supply rejection ratio PSRR 65 dB ƒ = 10 kHz, IOUT = 20 mA, VOUT ≥ 1 V 6
Power supply rejection ratio PSRR 40 dB ƒ = 100 kHz, IOUT = 20 mA, VOUT ≥ 1 V 6
Power supply rejection ratio PSRR 25 dB ƒ = 2 MHz, IOUT = 20 mA, VOUT ≥ 1 V 6
Output noise voltage eN 12 µVRMS BW = 10 Hz to 100 kHz; IOUT = 1 mA 6
Thermal shutdown TSD 160 °C TJ rising until output is OFF 6
Thermal hysteresis 15 °C TJ falling from shutdown 6
EN low threshold (Off) VIL 0.3 V VIN = 1.3 V to 3.3 V 6
EN high threshold (On) VIH 1 V 6
EN pin current IEN 3.3 µA VEN = 3.3 V, VIN = 3.3 V 6
EN pin current IEN 0.001 µA VEN = 0 V, VIN = 3.3 V 6
Line transient ΔVOUT 0 1 mV VIN = (VOUT(NOM) + 0.5 V) to (VOUT(NOM) + 1 V) in 30 µs, IOUT = 1 mA 6
Line transient ΔVOUT -1 0 mV VIN = (VOUT(NOM) + 1 V) to (VOUT(NOM) + 0.5 V) in 30 µs, IOUT = 1 mA 6
Load transient ΔVOUT -45 mV IOUT = 1 mA to 100 mA in 10 µs 6
Load transient ΔVOUT 45 mV IOUT = 100 mA to 1 mA in 10 µs 6
Turnon time tON 80 200 µs From VEN > VIH to VOUT = 95% of VOUT(NOM) 6
Overshoot on start-up 5 % 6
Output discharge pulldown resistance RAD 160 Ω VEN = 0 V, VIN = 2.3 V 6
Line regulation 0.01 %/V VIN = (VOUT(NOM) + 0.5 V) to 3.3 V, IOUT = 1 mA 5
Load regulation 0.002 %/mA IOUT = 1 mA to 300 mA 5
Junction-to-ambient thermal resistance RθJA 79.2 °C/W High-K board; WSON (DRV), two thermal vias (note 3) 5
Junction-to-case (top) thermal resistance RθJC(top) 110.2 °C/W WSON (DRV) 5
Junction-to-board thermal resistance RθJB 48.7 °C/W WSON (DRV) 5
Junction-to-top characterization parameter ψJT 5.2 °C/W WSON (DRV) 5
Junction-to-board characterization parameter ψJB 49.1 °C/W WSON (DRV) 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 18.1 °C/W WSON (DRV) 5

CAD (KiCad official)

  • Symbol: LP5910-1.0DRVR
  • Footprint: Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm
  • 3D model: WSON-6-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: lp5910-1-0drvr-etched.step / lp5910-1-0drvr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lp5910-1-0drvr.step / lp5910-1-0drvr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (32 pp, sha256 2b3ce53da67c4236, retrieved 2026-10-06, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF