main
History Download
Ray lp4078qvf: laser-etched CAD + chip hero (factory 2.0.0 backfill) 354d62a

LP4078QVF

LOWPOWER · Battery Management · DFN-10-EP(3x3)

LP4078QVF from LOWPOWER, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply source, typically connected to a wall adaptor. Operating range 4.5V-6V; withstands up to 40V (absolute max) with 22V OVP threshold. Bypass to GND with a 1-10 uF ceramic capacitor.
2 CHRG output Open-drain charge status output. Internal NMOS pulls the pin low while charging; goes high impedance when the charge cycle completes. Maximum sink current ~5 mA; requires an external pull-up resistor for logic-high state (typ. LED + 1k to BAT).
3 PG output Open-drain power-good status output. Pulls low when VIN is above the UVLO threshold and above VBAT+150 mV, and below the OVP threshold; Hi-Z otherwise. Requires an external pull-up; max sink 5 mA.
4 EN input Charge enable input (active low). Logic-low (<0.4V) or floating enables charging; logic-high (>1.4V) puts the device in shutdown. Tie to GND if the enable function is not needed.
5 NTC input NTC thermistor input for battery temperature monitoring per JEITA. Uses an internal 48 uA bias current with a 10k NTC (B=3370) between NTC and GND. Thresholds correspond to 0/10/60 °C; charge is halved between 0-10 °C and disabled below 0 °C or above 60 °C. Tie via a fixed 10k resistor to GND to disable the feature.
6 GND power_in Device ground. Connect to the system ground plane together with pin 11 (exposed pad).
7 NC unconnected No internal connection. Leave floating or tie to GND for best PCB layout.
8 IBF passive Charge termination current threshold program pin. Connect a resistor R_IBF from IBF to GND; termination current I_BF = (R_ISET x I_BAT) / R_IBF. Example: R_ISET=1.7k, R_IBF=17k -> 100 mA termination.
9 ISET passive Constant charge current program pin. Connect a resistor R_ISET from ISET to GND; constant current I_BAT = V_ISET x 1700 / R_ISET (V_ISET = 1V typ). R_ISET=1.7k gives ~1000 mA; R_ISET=3.4k gives ~500 mA.
10 BAT power_out Battery pin. Connect to the single-cell Li-Ion/Li-Polymer battery positive terminal. Regulated float voltage 4.20V/4.35V/4.40V per ordering suffix; withstand up to 15V absolute max. Bypass with a 1-10 uF capacitor placed close to the pin.
11 GND (PAD) power_in Exposed thermal pad on the package underside. Must be soldered to the PCB ground plane for electrical ground and thermal dissipation; add multiple vias to the ground plane to spread heat.

Key specifications

Parameter Value
Manufacturer LOWPOWER
Package DFN-10-EP(3x3)
Category PMIC
Pins 11

Ordering variants

Same part, different packaging or reel option.

  • LP4078QVF
  • LP4078QVF-435
  • LP4078QVF-440

CAD (KiCad official)

  • Symbol: LP4078QVF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lp4078qvf-etched.step / lp4078qvf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lp4078qvf.step / lp4078qvf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: LOWPOWER datasheet (11 pp, sha256 449276d21b78d6f5, retrieved 2026-08-17, tier: lcsc)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF