← Commit history
page.json+10−7@@ -32,7 +32,7 @@ "number": "1", "name": "IN", "type": "power_in",- "description": "Positive supply voltage input. Operating range 4.5V to 20V (28V absolute max). Place a 1\u00b5F ceramic capacitor from IN to PGND as close as possible to the IC."+ "description": "Positive supply voltage input. Operating range 4.5V to 20V (28V absolute max). Place a 1µF ceramic capacitor from IN to PGND as close as possible to the IC." }, { "number": "2",@@ -44,13 +44,13 @@ "number": "3", "name": "STAT", "type": "output",- "description": "Open-drain charge status output. Pulled low by an internal N-channel MOSFET while charging; high impedance when charge is complete. Maximum sink current 10mA; VOL \u2264 0.5V at ISTAT=5mA."+ "description": "Open-drain charge status output. Pulled low by an internal N-channel MOSFET while charging; high impedance when charge is complete. Maximum sink current 10mA; VOL ≤ 0.5V at ISTAT=5mA." }, { "number": "4", "name": "PMID", "type": "power_in",- "description": "Power MOSFET input, common node between the internal reverse-blocking FET and the high-side switching FET. Connect a 10\u00b5F ceramic capacitor from PMID to ground as close as possible to the IC."+ "description": "Power MOSFET input, common node between the internal reverse-blocking FET and the high-side switching FET. Connect a 10µF ceramic capacitor from PMID to ground as close as possible to the IC." }, { "number": "5",@@ -74,19 +74,19 @@ "number": "8", "name": "SW", "type": "output",- "description": "Switching node. Internally connected to the source of the high-side N-channel HSFET and the drain of the low-side N-channel LSFET. Connect to the external power inductor (typically 2.2\u00b5H-4.7\u00b5H). Switching frequency 520kHz."+ "description": "Switching node. Internally connected to the source of the high-side N-channel HSFET and the drain of the low-side N-channel LSFET. Connect to the external power inductor (typically 2.2µH-4.7µH). Switching frequency 520kHz." }, { "number": "9", "name": "CSP", "type": "input",- "description": "Charge current sensing positive input. Connect to the external current sense resistor Rcs (typically 25-50m\u03a9). Fast charge current IBAT = VCS/RCS with VCS typ. 51mV."+ "description": "Charge current sensing positive input. Connect to the external current sense resistor Rcs (typically 25-50mΩ). Fast charge current IBAT = VCS/RCS with VCS typ. 51mV." }, { "number": "10", "name": "BAT", "type": "power_out",- "description": "Battery voltage sensing and charge current sensing negative input. Connect to the positive terminal of the battery pack; 10\u00b5F ceramic capacitor recommended from BAT to PGND. Regulated float voltage 8.4V (LP4030HBQVF, 2-cell 4.2V/cell). Withstands up to 28V for input over-shoot protection."+ "description": "Battery voltage sensing and charge current sensing negative input. Connect to the positive terminal of the battery pack; 10µF ceramic capacitor recommended from BAT to PGND. Regulated float voltage 8.4V (LP4030HBQVF, 2-cell 4.2V/cell). Withstands up to 28V for input over-shoot protection." }, { "number": "11",@@ -156,5 +156,8 @@ "docs/lp4030hbqvf-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }