main
Ray
lp28013hqvf-435: laser-etched CAD + chip hero (factory 2.0.0 backfill)
ef534af
LP28013HQVF-435
LOWPOWER · Battery Management · TDFN-10-EP(3x3)
LP28013HQVF-435 from LOWPOWER, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input power source. Connect to a wall adapter (recommended 4.5V-5.8V, absolute max 36V). Requires 1uF decoupling capacitor; input OVP triggers at 6.3V and UVLO at 3.3V. |
| 2 | CHRG | output | Open-drain charge status output. Pulled low by internal NMOS during charging (~5mA sink); goes high-impedance when charging completes. Requires external pull-up resistor (typ. 1k to VBAT for LED indicator). |
| 3 | PG | output | Open-drain power-good status output. Low indicates VUVLO < VIN < VOVP (3.3V-6.3V) and input above battery voltage; Hi-Z otherwise. Requires external pull-up resistor. |
| 4 | EN | input | Charge enable input, active low. Logic-low (<0.4V) or floating enables the charger; logic-high (>1.4V) shuts down the IC. |
| 5 | NTC | input | Negative Thermal Coefficient thermistor input for battery temperature sensing (LP28013HQVF variant). Biased with internal 48uA source; designed for 10k NTC (β=3370, e.g. SEMITEC 103AT-2). Implements JEITA thresholds at 0/10/60°C. Tie 10k to GND to disable NTC feature. |
| 6 | GND | power_in | System ground connection. |
| 7 | NC | unconnected | No internal connection. Leave floating or tie to GND. |
| 8 | IBF | input | Charge termination current program. Connect a resistor RIBF from this pin to GND to set the termination (end-of-charge) current threshold: IBF = (RISET × IBAT) / RIBF. A 10nF decoupling capacitor is typically added. |
| 9 | ISET | input | Charge current program. Connect a 1% resistor (RISET) to GND to set the constant-current charge level: IBAT = (VISET × 1800)/RISET, where VISET ≈ 1V. RISET=1.8k → 1A; RISET=3.6k → 500mA. |
| 10 | BAT | power_out | Battery output connection. Regulated float voltage 4.35V (±1%) for the -435 variant. Requires a 10uF decoupling capacitor to GND. Sinks <1uA from battery when input supply is removed. |
| 11 | GND | power_in | Exposed thermal pad on the bottom of the TDFN-10 package. Must be soldered to the PCB ground plane for proper thermal dissipation (θJA=65°C/W) and electrical grounding. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | LOWPOWER |
| Package | TDFN-10-EP(3x3) |
| Category | PMIC |
| Pins | 11 |
Ordering variants
Same part, different packaging or reel option.
LP28013HQVF-435LP28013HTQVFLP28013HTQVF-435
Related parts (NOT interchangeable)
The extractor listed these alongside LP28013HQVF-435, but they are different parts with different electrical characteristics. Do not order them as substitutes.
LP28013HQVF-44LP28013HTQVF-44
CAD (KiCad official)
- Symbol:
LP28013HQVF-435 - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lp28013hqvf-435-etched.step/lp28013hqvf-435-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp28013hqvf-435.step/lp28013hqvf-435.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: LOWPOWER datasheet (10 pp, sha256
0218726a42d6f51e, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LP28013HQVF-435
**LOWPOWER** · Battery Management · TDFN-10-EP(3x3)
LP28013HQVF-435 from LOWPOWER, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input power source. Connect to a wall adapter (recommended 4.5V-5.8V, absolute max 36V). Requires 1uF decoupling capacitor; input OVP triggers at 6.3V and UVLO at 3.3V. |
| 2 | CHRG | output | Open-drain charge status output. Pulled low by internal NMOS during charging (~5mA sink); goes high-impedance when charging completes. Requires external pull-up resistor (typ. 1k to VBAT for LED indicator). |
| 3 | PG | output | Open-drain power-good status output. Low indicates VUVLO < VIN < VOVP (3.3V-6.3V) and input above battery voltage; Hi-Z otherwise. Requires external pull-up resistor. |
| 4 | EN | input | Charge enable input, active low. Logic-low (<0.4V) or floating enables the charger; logic-high (>1.4V) shuts down the IC. |
| 5 | NTC | input | Negative Thermal Coefficient thermistor input for battery temperature sensing (LP28013HQVF variant). Biased with internal 48uA source; designed for 10k NTC (β=3370, e.g. SEMITEC 103AT-2). Implements JEITA thresholds at 0/10/60°C. Tie 10k to GND to disable NTC feature. |
| 6 | GND | power_in | System ground connection. |
| 7 | NC | unconnected | No internal connection. Leave floating or tie to GND. |
| 8 | IBF | input | Charge termination current program. Connect a resistor RIBF from this pin to GND to set the termination (end-of-charge) current threshold: IBF = (RISET × IBAT) / RIBF. A 10nF decoupling capacitor is typically added. |
| 9 | ISET | input | Charge current program. Connect a 1% resistor (RISET) to GND to set the constant-current charge level: IBAT = (VISET × 1800)/RISET, where VISET ≈ 1V. RISET=1.8k → 1A; RISET=3.6k → 500mA. |
| 10 | BAT | power_out | Battery output connection. Regulated float voltage 4.35V (±1%) for the -435 variant. Requires a 10uF decoupling capacitor to GND. Sinks <1uA from battery when input supply is removed. |
| 11 | GND | power_in | Exposed thermal pad on the bottom of the TDFN-10 package. Must be soldered to the PCB ground plane for proper thermal dissipation (θJA=65°C/W) and electrical grounding. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | LOWPOWER |
| Package | TDFN-10-EP(3x3) |
| Category | PMIC |
| Pins | 11 |
## Ordering variants
Same part, different packaging or reel option.
- `LP28013HQVF-435`
- `LP28013HTQVF`
- `LP28013HTQVF-435`
## Related parts (NOT interchangeable)
The extractor listed these alongside LP28013HQVF-435, but they are **different parts** with different electrical characteristics. Do not order them as substitutes.
- `LP28013HQVF-44`
- `LP28013HTQVF-44`
## CAD (KiCad official)
- Symbol: `LP28013HQVF-435`
- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`
- 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `lp28013hqvf-435-etched.step` / `lp28013hqvf-435-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lp28013hqvf-435.step` / `lp28013hqvf-435.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [LOWPOWER datasheet](docs/lp28013hqvf-435-datasheet.pdf) (10 pp, sha256 `0218726a42d6f51e`, retrieved 2026-08-17, tier: lcsc)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lp28013hqvf-435-datasheet.pdf)