← Commit history

Initial commit: component/lmr33640addar

Ray ·0f1bd2cd87 ·
2 files changed +196
README.mdadded+46
@@ -0,0 +1,46 @@+# LMR33640ADDAR++**Texas Instruments** · Global Sourcing Parts · ESOP-8++LMR33640ADDAR from Texas Instruments, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PGND | power_in | Power ground terminal; connect to system ground and AGND with short wide traces to the bypass capacitor. |+| 2 | VIN | power_in | Input supply to the regulator; connect a high-quality bypass capacitor directly from this pin to PGND. |+| 3 | EN | input | Enable input to the regulator; high = ON, low = OFF, can be tied directly to VIN but must not be left floating. |+| 4 | PG | output | Open-drain power-good flag output requiring an external pull-up resistor; high = power OK, low = power bad, and pulls low when EN is low; may be left open when unused. |+| 5 | FB | input | Feedback input to the regulator; connect to the tap point of the output feedback voltage divider and must not be left floating or grounded. |+| 6 | VCC | power_out | Internal 5-V LDO output used to supply internal control circuits; do not connect external loads, connect a high-quality 1-µF capacitor from this pin to PGND. |+| 7 | BOOT | passive | Bootstrap supply voltage for the internal high-side driver; connect a high-quality 100-nF capacitor from this pin to the SW pin. |+| 8 | SW | output | Regulator switch node; connect to the power inductor. |+| 9 | AGND | power_in | Analog ground/thermal pad on the bottom of the device; serves as the ground reference for internal references and logic and as the thermal connection to the PCB heat-sink ground plane; must be soldered to a ground plane for proper electrical and thermal performance. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | ESOP-8 |+| Category | Global Sourcing Parts |+| Pins | 9 |++## CAD (KiCad official)++- Symbol: `LMR33640ADDAR`+- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm`+- 3D model: ESOP-8 (KiCad packages3D, STEP)+- 3D model files: `lmr33640addar-etched.step` / `lmr33640addar-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmr33640addar.step` / `lmr33640addar.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lmr33640) (44 pp, sha256 `6df39cb52faaed45`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lmr33640addar-datasheet.pdf)
page.jsonadded+150
@@ -0,0 +1,150 @@+{+  "slug": "lmr33640addar",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Global Sourcing Parts, ESOP-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "global sourcing parts",+    "lmr33640addar",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lmr33640addar.kicad_sym",+    "lmr33640addar.kicad_mod",+    "lmr33640addar.glb",+    "lmr33640addar.step",+    "lmr33640addar.lbr",+    "docs/hero.png",+    "docs/lmr33640addar-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LMR33640ADDAR",+    "manufacturer": "Texas Instruments",+    "package": "ESOP-8",+    "pin_count": 9,+    "category": "Global Sourcing Parts",+    "subcategory": "Global Sourcing Parts",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lmr33640",+    "parts": {+      "symbol": "lmr33640addar.kicad_sym",+      "footprint": "lmr33640addar.kicad_mod",+      "model_3d": "lmr33640addar-etched.glb",+      "model_3d_plain": "lmr33640addar.glb",+      "model_3d_step": "lmr33640addar-etched.step",+      "model_3d_step_plain": "lmr33640addar.step",+      "lbr": "lmr33640addar.lbr"+    },+    "distributor_links": {+      "lcsc": "C2836966"+    },+    "pins": [+      {+        "number": "1",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground terminal; connect to system ground and AGND with short wide traces to the bypass capacitor."+      },+      {+        "number": "2",+        "name": "VIN",+        "type": "power_in",+        "description": "Input supply to the regulator; connect a high-quality bypass capacitor directly from this pin to PGND."+      },+      {+        "number": "3",+        "name": "EN",+        "type": "input",+        "description": "Enable input to the regulator; high = ON, low = OFF, can be tied directly to VIN but must not be left floating."+      },+      {+        "number": "4",+        "name": "PG",+        "type": "output",+        "description": "Open-drain power-good flag output requiring an external pull-up resistor; high = power OK, low = power bad, and pulls low when EN is low; may be left open when unused."+      },+      {+        "number": "5",+        "name": "FB",+        "type": "input",+        "description": "Feedback input to the regulator; connect to the tap point of the output feedback voltage divider and must not be left floating or grounded."+      },+      {+        "number": "6",+        "name": "VCC",+        "type": "power_out",+        "description": "Internal 5-V LDO output used to supply internal control circuits; do not connect external loads, connect a high-quality 1-µF capacitor from this pin to PGND."+      },+      {+        "number": "7",+        "name": "BOOT",+        "type": "passive",+        "description": "Bootstrap supply voltage for the internal high-side driver; connect a high-quality 100-nF capacitor from this pin to the SW pin."+      },+      {+        "number": "8",+        "name": "SW",+        "type": "output",+        "description": "Regulator switch node; connect to the power inductor."+      },+      {+        "number": "9",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground/thermal pad on the bottom of the device; serves as the ground reference for internal references and logic and as the thermal connection to the PCB heat-sink ground plane; must be soldered to a ground plane for proper electrical and thermal performance."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 9 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 44,+        "cost_usd": 0.4556,+        "at": "2026-09-23T00:49:44"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lmr33640",+        "pages": 44,+        "sha256": "6df39cb52faaed45",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 9,+        "described": 9,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file