main
Ray
lmr33630adda: specified limits as data (metadata.characteristics, 60 rows from the datasheet)
da614f3
LMR33630ADDA
Texas Instruments · DC-DC Converters · ESOP-8
LMR33630ADDA from Texas Instruments, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGND | power_in | Power ground terminal; connect to system ground and AGND with bypass capacitor using short wide traces. |
| 2 | VIN | power_in | Input voltage supply to regulator (3.8V to 36V); connect high-quality bypass capacitor or capacitors directly to this pin and PGND. |
| 3 | EN | input | Enable input to regulator with rising threshold of 1.231V typical; high = ON, low = OFF; can connect directly to VIN but must not float. |
| 4 | PG | output | Open-drain power-good flag output; connect to suitable voltage supply through current-limiting resistor; pulls low during current limit, thermal shutdown, or startup. |
| 5 | FB | input | Feedback input for regulator with 1V reference (0.985V to 1.015V nominal); connect to feedback voltage divider tap; must not float or be grounded. |
| 6 | VCC | power_out | Internal 5V LDO output (4.75V to 5.25V) supplying control circuits; connect 1-µF high-quality ceramic capacitor from this pin to GND; do not connect external loads. |
| 7 | BOOT | power_in | Bootstrap supply voltage for internal high-side gate driver (-0.3V to 5.5V relative to SW); connect 100-nF high-quality ceramic capacitor from this pin to SW. |
| 8 | SW | output | Regulator switch node connecting to power inductor; switches between VIN and ground through internal power MOSFETs at 400kHz switching frequency. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to PGND | -0.3 | 38 | V | 5 | |||
| EN to AGND (max VIN + 0.3 V as printed) | -0.3 | V | 5 | ||||
| FB to AGND | -0.3 | 5.5 | V | 5 | |||
| PG to AGND | 0 | 22 | V | 5 | |||
| AGND to PGND | -0.3 | 0.3 | V | 5 | |||
| SW to PGND (max VIN + 0.3 V as printed) | -0.3 | V | 5 | ||||
| SW to PGND less than 100-ns transients | -3.5 | 38 | V | less than 100-ns transients | 5 | ||
| BOOT to SW | -0.3 | 5.5 | V | 5 | |||
| VCC to AGND | -0.3 | 5.5 | V | 5 | |||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 5 | ||
| Input voltage VIN to PGND | VIN | 3.8 | 36 | V | 5 | ||
| EN (max VIN + 0.3 V as printed) | EN | 0 | V | 5 | |||
| PG | PG | 0 | 18 | V | 5 | ||
| Adjustable output voltage | VOUT | 1 | 24 | V | 5 | ||
| Output current | IOUT | 0 | 3 | A | 5 | ||
| Minimum operating input voltage | VIN | 3.8 | V | 6 | |||
| Non-switching input current, measured at VIN pin | IQ | 24 | 34 | µA | VFB = 1.2 V | 6 | |
| Shutdown quiescent current, measured at VIN pin | ISD | 5 | 10 | µA | EN = 0 V | 6 | |
| EN input level required to start switching, rising threshold | VEN-H | 1.2 | 1.231 | 1.26 | V | Rising threshold | 6 |
| Internal LDO output voltage at VCC pin | VCC | 4.75 | 5 | 5.25 | V | 6 V ≤ VIN ≤ 36 V | 6 |
| Feedback voltage; ADJ option | VFB | 0.985 | 1 | 1.015 | V | ADJ option | 6 |
| Current into FB pin; ADJ option | IFB | 0.2 | 50 | nA | ADJ option; FB = 1 V | 6 | |
| High-side current limit | ISC | 3.85 | 4.5 | 5.05 | A | LMR33630 | 6 |
| Low-side current limit | ILIMIT | 2.9 | 3.5 | 4.1 | A | LMR33630 | 6 |
| Internal soft-start time | tSS | 2.9 | 4 | 6 | ms | 7 | |
| Power-good upper threshold, rising, % of FB voltage | VPG-HIGH-UP | 105 | 107 | 110 | % | 7 | |
| Power-good upper threshold, falling, % of FB voltage | VPG-HIGH-DN | 103 | 105 | 108 | % | 7 | |
| Power-good lower threshold, rising, % of FB voltage | VPG-LOW-UP | 92 | 94 | 97 | % | 7 | |
| Power-good lower threshold, falling, % of FB voltage | VPG-LOW-DN | 90 | 92 | 95 | % | 7 | |
| Power-good glitch filter delay | tPG | 60 | 170 | µs | 7 | ||
| Power-good flag RDSON | RPG | 76 | 150 | Ω | VIN = 12 V, VEN = 4 V | 7 | |
| Power-good flag RDSON | RPG | 35 | 60 | Ω | VEN = 0 V | 7 | |
| Switching frequency A version | ƒSW | 340 | 400 | 460 | kHz | A version | 7 |
| High-side MOSFET ON-resistance, DDA package | RDS-ON-HS | 95 | 160 | mΩ | DDA package | 7 | |
| Low-side MOSFET ON-resistance, DDA package | RDS-ON-LS | 66 | 110 | mΩ | DDA package | 7 | |
| Minimum switch on-time, DDA package | tON-MIN | 75 | 108 | ns | DDA package | 7 | |
| Minimum switch off-time, DDA package | tOFF-MIN | 50 | 85 | ns | DDA package | 7 | |
| Maximum switch on-time | tON-MAX | 7 | 9 | µs | 7 | ||
| Operating input voltage range | VIN | 3.8 | 36 | V | VOUT = 3.3 V, IOUT = 0 A | 8 | |
| Output voltage regulation for VOUT = 5 V | VOUT | -1.5 | 2.5 | % | VOUT = 5 V, VIN = 7 V to 36 V, IOUT = 0 A to max. load | 8 | |
| Output voltage regulation for VOUT = 5 V | VOUT | -1.5 | 1.5 | % | VOUT = 5 V, VIN = 7 V to 36 V, IOUT = 1 A to max. load | 8 | |
| Output voltage regulation for VOUT = 3.3 V | VOUT | -1.5 | 2.5 | % | VOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 0 A to max. load | 8 | |
| Output voltage regulation for VOUT = 3.3 V | VOUT | -1.5 | 1.5 | % | VOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 1 A to max. load | 8 | |
| RθJA junction-to-ambient thermal resistance (DDA HSOIC, 8 pins) | RθJA | 42.9 | °C/W | DDA (HSOIC), 8 pins | 6 | ||
| RθJC(top) junction-to-case (top) thermal resistance (DDA, 8 pins) | RθJC(top) | 54 | °C/W | DDA (HSOIC), 8 pins | 6 | ||
| RθJB junction-to-board thermal resistance (DDA, 8 pins) | RθJB | 13.6 | °C/W | DDA (HSOIC), 8 pins | 6 | ||
| ψJT junction-to-top characterization parameter (DDA, 8 pins) | ψJT | 4.3 | °C/W | DDA (HSOIC), 8 pins | 6 | ||
| ψJB junction-to-board characterization parameter (DDA, 8 pins) | ψJB | 13.8 | °C/W | DDA (HSOIC), 8 pins | 6 | ||
| RθJC(bot) junction-to-case (bottom) thermal resistance (DDA, 8 pins) | RθJC(bot) | 4.3 | °C/W | DDA (HSOIC), 8 pins | 6 | ||
| Enable threshold to turn on internal LDO, rising | VEN-VCC-H | 1 | V | Rising threshold | 6 | ||
| Enable threshold to turn off internal LDO, falling | VEN-VCC-L | 0.3 | V | Falling threshold | 6 | ||
| Bootstrap voltage undervoltage lock-out threshold | VBOOT-UVLO | 2.2 | V | 6 | |||
| Minimum peak inductor current | IPEAK-MIN | 0.69 | A | LMR33630 | 6 | ||
| Zero current detector threshold | IZC | -0.106 | A | 7 | |||
| Minimum input voltage for proper PG function | VIN-PG | 2 | V | 50-µA, EN = 0 V | 7 | ||
| PG logic low output | VPG | 0.2 | V | 50-µA, EN = 0 V, VIN = 2V | 7 | ||
| Input supply current when in regulation | ISUPPLY | 25 | µA | VIN = 12 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩ | 8 | ||
| Dropout voltage (VIN − VOUT) | VDROP | 150 | mV | VOUT = 5 V, IOUT = 1A | 8 | ||
| Thermal shutdown temperature | TSD | 165 | °C | Shutdown temperature | 8 |
CAD (KiCad official)
- Symbol:
LMR33630ADDA - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
lmr33630adda-etched.step/lmr33630adda-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr33630adda.step/lmr33630adda.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (57 pp, sha256
71bca20c1f8dd624, retrieved 2026-09-26, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LMR33630ADDA
**Texas Instruments** · DC-DC Converters · ESOP-8
LMR33630ADDA from Texas Instruments, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGND | power_in | Power ground terminal; connect to system ground and AGND with bypass capacitor using short wide traces. |
| 2 | VIN | power_in | Input voltage supply to regulator (3.8V to 36V); connect high-quality bypass capacitor or capacitors directly to this pin and PGND. |
| 3 | EN | input | Enable input to regulator with rising threshold of 1.231V typical; high = ON, low = OFF; can connect directly to VIN but must not float. |
| 4 | PG | output | Open-drain power-good flag output; connect to suitable voltage supply through current-limiting resistor; pulls low during current limit, thermal shutdown, or startup. |
| 5 | FB | input | Feedback input for regulator with 1V reference (0.985V to 1.015V nominal); connect to feedback voltage divider tap; must not float or be grounded. |
| 6 | VCC | power_out | Internal 5V LDO output (4.75V to 5.25V) supplying control circuits; connect 1-µF high-quality ceramic capacitor from this pin to GND; do not connect external loads. |
| 7 | BOOT | power_in | Bootstrap supply voltage for internal high-side gate driver (-0.3V to 5.5V relative to SW); connect 100-nF high-quality ceramic capacitor from this pin to SW. |
| 8 | SW | output | Regulator switch node connecting to power inductor; switches between VIN and ground through internal power MOSFETs at 400kHz switching frequency. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to PGND | | -0.3 | | 38 | V | | 5 |
| EN to AGND (max VIN + 0.3 V as printed) | | -0.3 | | | V | | 5 |
| FB to AGND | | -0.3 | | 5.5 | V | | 5 |
| PG to AGND | | 0 | | 22 | V | | 5 |
| AGND to PGND | | -0.3 | | 0.3 | V | | 5 |
| SW to PGND (max VIN + 0.3 V as printed) | | -0.3 | | | V | | 5 |
| SW to PGND less than 100-ns transients | | -3.5 | | 38 | V | less than 100-ns transients | 5 |
| BOOT to SW | | -0.3 | | 5.5 | V | | 5 |
| VCC to AGND | | -0.3 | | 5.5 | V | | 5 |
| Junction temperature | TJ | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -55 | | 150 | °C | | 5 |
| Input voltage VIN to PGND | VIN | 3.8 | | 36 | V | | 5 |
| EN (max VIN + 0.3 V as printed) | EN | 0 | | | V | | 5 |
| PG | PG | 0 | | 18 | V | | 5 |
| Adjustable output voltage | VOUT | 1 | | 24 | V | | 5 |
| Output current | IOUT | 0 | | 3 | A | | 5 |
| Minimum operating input voltage | VIN | 3.8 | | | V | | 6 |
| Non-switching input current, measured at VIN pin | IQ | | 24 | 34 | µA | VFB = 1.2 V | 6 |
| Shutdown quiescent current, measured at VIN pin | ISD | | 5 | 10 | µA | EN = 0 V | 6 |
| EN input level required to start switching, rising threshold | VEN-H | 1.2 | 1.231 | 1.26 | V | Rising threshold | 6 |
| Internal LDO output voltage at VCC pin | VCC | 4.75 | 5 | 5.25 | V | 6 V ≤ VIN ≤ 36 V | 6 |
| Feedback voltage; ADJ option | VFB | 0.985 | 1 | 1.015 | V | ADJ option | 6 |
| Current into FB pin; ADJ option | IFB | | 0.2 | 50 | nA | ADJ option; FB = 1 V | 6 |
| High-side current limit | ISC | 3.85 | 4.5 | 5.05 | A | LMR33630 | 6 |
| Low-side current limit | ILIMIT | 2.9 | 3.5 | 4.1 | A | LMR33630 | 6 |
| Internal soft-start time | tSS | 2.9 | 4 | 6 | ms | | 7 |
| Power-good upper threshold, rising, % of FB voltage | VPG-HIGH-UP | 105 | 107 | 110 | % | | 7 |
| Power-good upper threshold, falling, % of FB voltage | VPG-HIGH-DN | 103 | 105 | 108 | % | | 7 |
| Power-good lower threshold, rising, % of FB voltage | VPG-LOW-UP | 92 | 94 | 97 | % | | 7 |
| Power-good lower threshold, falling, % of FB voltage | VPG-LOW-DN | 90 | 92 | 95 | % | | 7 |
| Power-good glitch filter delay | tPG | | 60 | 170 | µs | | 7 |
| Power-good flag RDSON | RPG | | 76 | 150 | Ω | VIN = 12 V, VEN = 4 V | 7 |
| Power-good flag RDSON | RPG | | 35 | 60 | Ω | VEN = 0 V | 7 |
| Switching frequency A version | ƒSW | 340 | 400 | 460 | kHz | A version | 7 |
| High-side MOSFET ON-resistance, DDA package | RDS-ON-HS | | 95 | 160 | mΩ | DDA package | 7 |
| Low-side MOSFET ON-resistance, DDA package | RDS-ON-LS | | 66 | 110 | mΩ | DDA package | 7 |
| Minimum switch on-time, DDA package | tON-MIN | | 75 | 108 | ns | DDA package | 7 |
| Minimum switch off-time, DDA package | tOFF-MIN | | 50 | 85 | ns | DDA package | 7 |
| Maximum switch on-time | tON-MAX | | 7 | 9 | µs | | 7 |
| Operating input voltage range | VIN | 3.8 | | 36 | V | VOUT = 3.3 V, IOUT = 0 A | 8 |
| Output voltage regulation for VOUT = 5 V | VOUT | -1.5 | | 2.5 | % | VOUT = 5 V, VIN = 7 V to 36 V, IOUT = 0 A to max. load | 8 |
| Output voltage regulation for VOUT = 5 V | VOUT | -1.5 | | 1.5 | % | VOUT = 5 V, VIN = 7 V to 36 V, IOUT = 1 A to max. load | 8 |
| Output voltage regulation for VOUT = 3.3 V | VOUT | -1.5 | | 2.5 | % | VOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 0 A to max. load | 8 |
| Output voltage regulation for VOUT = 3.3 V | VOUT | -1.5 | | 1.5 | % | VOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 1 A to max. load | 8 |
| RθJA junction-to-ambient thermal resistance (DDA HSOIC, 8 pins) | RθJA | | 42.9 | | °C/W | DDA (HSOIC), 8 pins | 6 |
| RθJC(top) junction-to-case (top) thermal resistance (DDA, 8 pins) | RθJC(top) | | 54 | | °C/W | DDA (HSOIC), 8 pins | 6 |
| RθJB junction-to-board thermal resistance (DDA, 8 pins) | RθJB | | 13.6 | | °C/W | DDA (HSOIC), 8 pins | 6 |
| ψJT junction-to-top characterization parameter (DDA, 8 pins) | ψJT | | 4.3 | | °C/W | DDA (HSOIC), 8 pins | 6 |
| ψJB junction-to-board characterization parameter (DDA, 8 pins) | ψJB | | 13.8 | | °C/W | DDA (HSOIC), 8 pins | 6 |
| RθJC(bot) junction-to-case (bottom) thermal resistance (DDA, 8 pins) | RθJC(bot) | | 4.3 | | °C/W | DDA (HSOIC), 8 pins | 6 |
| Enable threshold to turn on internal LDO, rising | VEN-VCC-H | | 1 | | V | Rising threshold | 6 |
| Enable threshold to turn off internal LDO, falling | VEN-VCC-L | | 0.3 | | V | Falling threshold | 6 |
| Bootstrap voltage undervoltage lock-out threshold | VBOOT-UVLO | | 2.2 | | V | | 6 |
| Minimum peak inductor current | IPEAK-MIN | | 0.69 | | A | LMR33630 | 6 |
| Zero current detector threshold | IZC | | -0.106 | | A | | 7 |
| Minimum input voltage for proper PG function | VIN-PG | | 2 | | V | 50-µA, EN = 0 V | 7 |
| PG logic low output | VPG | | 0.2 | | V | 50-µA, EN = 0 V, VIN = 2V | 7 |
| Input supply current when in regulation | ISUPPLY | | 25 | | µA | VIN = 12 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩ | 8 |
| Dropout voltage (VIN − VOUT) | VDROP | | 150 | | mV | VOUT = 5 V, IOUT = 1A | 8 |
| Thermal shutdown temperature | TSD | | 165 | | °C | Shutdown temperature | 8 |
## CAD (KiCad official)
- Symbol: `LMR33630ADDA`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm`
- 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files: `lmr33630adda-etched.step` / `lmr33630adda-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmr33630adda.step` / `lmr33630adda.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lmr33630) (57 pp, sha256 `71bca20c1f8dd624`, retrieved 2026-09-26, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lmr33630adda-datasheet.pdf)