main
Ray Publish 0.1.0 13a2470

LMR14050SQDPRTQ1

Texas Instruments · DC-DC Converters · WSON-10-EP(4x4)

LMR14050SQDPRTQ1 from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BOOT passive Bootstrap capacitor connection for the high-side MOSFET driver; connect a high quality 0.1 µF capacitor from BOOT to SW (BOOT to SW max 6.5 V in DPR package).
2 VIN power_in Connects to the power supply and bypass capacitors CIN (4 V to 40 V operating); the path from VIN to the high frequency bypass CIN and GND must be as short as possible.
3 VIN power_in Second VIN pin, connected to the power supply and bypass capacitors CIN (4 V to 40 V operating) with the same short path to CIN and GND.
4 EN input Enable pin with internal pull-up current source; pull below 1.2 V to disable, float or connect to VIN to enable, and adjust the input undervoltage lockout with two resistors.
5 RT/SYNC input Resistor timing or external clock input; a resistor to ground sets switching frequency (200 kHz to 2500 kHz), or the pin becomes a high-impedance synchronization input to the internal PLL when pulled above the PLL upper threshold.
6 SS input Soft-start control pin; connect a capacitor to set the soft-start time.
7 FB input Feedback input connected to the feedback divider to set VOUT; do not short this pin to ground during operation.
8 PGOOD output Open drain power-good flag output; use a 10 kΩ to 100 kΩ pull-up resistor to a logic rail or DC voltage no higher than 7 V.
9 GND power_in System ground pin.
10 SW passive Switching output of the regulator, internally connected to the high-side power MOSFET; connect to the power inductor.
11 Thermal Pad power_in Exposed pad and major heat dissipation path of the die; must be connected to the ground plane on the PCB.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-10-EP(4x4)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operation input voltage VIN 4 40 V 5
UVLO rising threshold UVLO 3.5 3.7 3.9 V Rising threshold 5
Shutdown supply current ISHDN 1 3 μA VEN = 0 V, TJ = 25°C, 4.0 V ≤ VIN ≤ 40 V 5
EN threshold voltage VEN_TH 1.05 1.2 1.38 V 5
PGOOD leakage current at high level output IPG 10 200 nA VPull-Up = 5 V 5
Minimum VIN for valid PGOOD output VIN_PG_MIN 1.6 1.95 V VPull-Up < 5 V at IPull-Up = 100 μA 5
Feedback voltage VFB 0.744 0.75 0.756 V TJ = 25°C 5
Feedback voltage over temperature VFB 0.735 0.75 0.765 V TJ = -40 °C to 125°C 5
High-side MOSFET on-resistance RDS_ON 90 180 mΩ VIN = 12 V 6
Current limit ILIMT 5.8 7.9 10.9 A VIN = 12 V, TJ = -40°C to 125°C, Open Loop 6
Switching frequency fSW 1758 1912 2066 kHz RT = 11.5 kΩ 6
Switching frequency range at SYNC mode fSW 250 2300 kHz 6
Absolute max VIN, EN to GND VIN, EN -0.3 44 V 4
Absolute max BOOT to GND BOOT -0.3 49 V 4
Absolute max SS to GND SS -0.3 5 V 4
Absolute max FB to GND (DPR package) FB -0.3 7 V DPR package 4
Absolute max RT/SYNC to GND RT/SYNC -0.3 3.6 V 4
Absolute max PGOOD to GND PGOOD -0.3 7 V 4
Absolute max BOOT to SW (DPR package) BOOT to SW 6.5 V DPR package 4
Absolute max SW to GND SW -3 44 V 4
Junction temperature (absolute max) TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
ESD HBM V(ESD) -2000 2000 V Human-body model, per AEC Q100-002 4
ESD CDM V(ESD) -750 750 V Charged-device model, per AEC Q100-011 4
Recommended VIN VIN 4 40 V 4
Recommended VOUT VOUT 0.8 28 V 4
Recommended BOOT BOOT 45 V 4
Recommended SW SW -1 40 V 4
Recommended FB FB 0 5 V 4
Recommended EN EN 0 40 V 4
Recommended RT/SYNC RT/SYNC 0 3.3 V 4
Recommended SS SS 0 3 V 4
Recommended PGOOD to GND PGOOD 0 5 V 4
Switching frequency range at RT mode fSW 200 2500 kHz 4
Switching frequency range at SYNC mode (recommended) fSW 250 2300 kHz 4
Operating junction temperature TJ -40 125 °C 4
Operating quiescent current (non-switching) IQ 40 μA VFB = 1.0 V, TJ = 25°C 5
UVLO hysteresis UVLO 285 mV Hysteresis 5
EN hysteresis current IEN_HYS -3.6 μA 5
SS pin current ISS -3 μA TJ = 25°C 5
Thermal shutdown threshold TSHDN 170 °C 6
Thermal shutdown hysteresis THYS 12 °C 6
Minimum controllable on time TON_MIN 75 ns VIN = 12 V, ILoad = 1 A 6
Maximum duty cycle DMAX 97 % fSW = 200 kHz 6
Junction-to-ambient thermal resistance (DPR) RθJA 36.5 °C/W DPR (WSON) 10 pins 5
Junction-to-case (bottom) thermal resistance (DPR) RθJC(bot) 3.1 °C/W DPR (WSON) 10 pins 5
Junction-to-case (top) thermal resistance (DPR) RθJC(top) 35.2 °C/W DPR (WSON) 10 pins 5
Junction-to-board thermal resistance (DPR) RθJB 13.6 °C/W DPR (WSON) 10 pins 5
Junction-to-top characterization parameter (DPR) ψJT 0.3 °C/W DPR (WSON) 10 pins 5
Junction-to-board characterization parameter (DPR) ψJB 13.8 °C/W DPR (WSON) 10 pins 5

CAD (KiCad official)

  • Symbol: LMR14050SQDPRTQ1
  • Footprint: Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm
  • 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lmr14050sqdprtq1-etched.step / lmr14050sqdprtq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmr14050sqdprtq1.step / lmr14050sqdprtq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (38 pp, sha256 cefdbbf1b3380e4f, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF