main
Ray
Publish 0.1.0
b3ae388
LMKDB1108Z85RKPR
Texas Instruments · IC · VQFN-40(5x5)
LMKDB1108Z85RKPR from Texas Instruments, in a VQFN-40(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LOS# | output | Open-drain loss-of-input-clock status output, requires an external pullup resistor; low = invalid input clock, high = valid input clock. |
| 2 | ^SLEWRATE_SEL | input | LP-HCSL output slew rate select input with internal pullup; low = slow slew rate, high = fast slew rate. |
| 3 | ^vSADR1_tri | input | SMBus address 3-level input with internal pullup and pulldown resistors. |
| 4 | ^vSADR0_tri | input | SMBus address 3-level input with internal pullup and pulldown resistors. |
| 5 | SMB_DATA | bidirectional | SMBus data line, requires an external pullup resistor, no connect if unused. |
| 6 | SMB_CLK | input | SMBus clock input, requires an external pullup resistor, no connect if unused. |
| 7 | VDDA | power_in | Analog power supply; additional power supply filtering is recommended (see Section 10.3). |
| 8 | CLKIN_P | input | Positive side of the differential clock input. |
| 9 | CLKIN_N | input | Negative side of the differential clock input. |
| 10 | VDDCLK | power_in | Output power supply. |
| 11 | vSBI_EN | input | SBI enable input with internal pulldown, state must not be changed after power-up; low at power-up = SBI disabled, high at power-up = SBI enabled with SMBus and other OE pins remaining functional. |
| 12 | vPWRGD/PWRDN# | input | Multifunction input with internal pulldown that acts as power good on the first low-to-high transition and as active-low power down afterwards (low = power-down mode, high = normal operation). |
| 13 | VDDCLK | power_in | Output power supply. |
| 14 | vOE0#/SHFT_LD# | input | Active-low output enable for CLK0 (0 = active, 1 = inactive) or SBI active-low shift register load input depending on SBI_EN, with internal pulldown. |
| 15 | CLK0_P | output | LP-HCSL differential clock output 0 positive, no connect if unused. |
| 16 | CLK0_N | output | LP-HCSL differential clock output 0 negative, no connect if unused. |
| 17 | CLK1_P | output | LP-HCSL differential clock output 1 positive, no connect if unused. |
| 18 | CLK1_N | output | LP-HCSL differential clock output 1 negative, no connect if unused. |
| 19 | vOE1#/SBI_IN | input | Active-low output enable for CLK1 (0 = active, 1 = inactive) or SBI data input depending on SBI_EN, with internal pulldown. |
| 20 | VDDCLK | power_in | Output power supply. |
| 21 | vOE2# | input | Active-low output enable for CLK2 with internal pulldown; 0 = output active, 1 = output inactive. |
| 22 | CLK2_P | output | LP-HCSL differential clock output 2 positive, no connect if unused. |
| 23 | CLK2_N | output | LP-HCSL differential clock output 2 negative, no connect if unused. |
| 24 | CLK3_P | output | LP-HCSL differential clock output 3 positive, no connect if unused. |
| 25 | CLK3_N | output | LP-HCSL differential clock output 3 negative, no connect if unused. |
| 26 | VDDCLK | power_in | Output power supply. |
| 27 | vOE3# | input | Active-low output enable for CLK3 with internal pulldown; 0 = output active, 1 = output inactive. |
| 28 | CLK4_P | output | LP-HCSL differential clock output 4 positive, no connect if unused. |
| 29 | CLK4_N | output | LP-HCSL differential clock output 4 negative, no connect if unused. |
| 30 | vOE4#/SBI_CLK | input | Active-low output enable for CLK4 (0 = active, 1 = inactive) or SBI clock input depending on SBI_EN, with internal pulldown. |
| 31 | CLK5_P | output | LP-HCSL differential clock output 5 positive, no connect if unused. |
| 32 | CLK5_N | output | LP-HCSL differential clock output 5 negative, no connect if unused. |
| 33 | vOE5# | input | Active-low output enable for CLK5 with internal pulldown; 0 = output active, 1 = output inactive. |
| 34 | vOE6#/SBI_OUT | bidirectional | Active-low output enable input for CLK6 (0 = active, 1 = inactive) or SBI shift register data output depending on SBI_EN, with internal pulldown. |
| 35 | CLK6_P | output | LP-HCSL differential clock output 6 positive, no connect if unused. |
| 36 | CLK6_N | output | LP-HCSL differential clock output 6 negative, no connect if unused. |
| 37 | VDDCLK | power_in | Output power supply. |
| 38 | CLK7_P | output | LP-HCSL differential clock output 7 positive, no connect if unused. |
| 39 | CLK7_N | output | LP-HCSL differential clock output 7 negative, no connect if unused. |
| 40 | vOE7# | input | Active-low output enable for CLK7 with internal pulldown; 0 = output active, 1 = output inactive. |
| 41 | Thermal Pad (GND) | power_in | Device ground, thermal pad. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-40(5x5) |
| Category | |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDx Supply voltage on any VDD pin | VDDx | -0.3 | 3.63 | V | 22 | ||
| VIN Input voltage on CLKIN and digital input pins | VIN | -0.3 | 3.63 | V | 22 | ||
| Output current - continuous (CLKOUT) | IOUT | 30 | mA | 22 | |||
| Output current - continuous (SMB_DATA, SBI_OUT) | IOUT | 25 | mA | 22 | |||
| Output current - surge (CLKOUT) | IOUT | 60 | mA | 22 | |||
| Output current - surge (SMB_DATA, SBI_OUT) | IOUT | 50 | mA | 22 | |||
| Storage temperature | TS | -65 | 150 | ℃ | 22 | ||
| Junction temperature | TJ | 125 | °C | 22 | |||
| Ambient temperature | TA | -40 | 105 | °C | 22 | ||
| Power supply voltage (3.3 V row) | VDD | 2.97 | 3.3 | 3.6 | V | 22 | |
| Power supply voltage (1.8 V row) | VDD | 1.71 | 1.8 | 1.89 | V | 22 | |
| Input voltage on CLKIN and digital input pins (recommended) | VIN | -0.3 | 3.6 | V | 22 | ||
| Power ramping time | tramp | 0.05 | 5 | ms | 22 | ||
| Clock input crossing point voltage | VIN,cross | 100 | 1400 | mV | 23 | ||
| Clock input duty cycle | DCIN | 45 | 55 | % | 23 | ||
| Differential clock input amplitude (half of differential peak-peak voltage) | VIN | 200 | 2000 | mV | f0 ≤ 300MHz | 23 | |
| Differential clock input amplitude (half of differential peak-peak voltage) | VIN | 250 | 2000 | mV | 300MHz < f0 ≤ 400MHz | 23 | |
| Output voltage high | VOH,AC | 670 | 820 | mV | Output swing programmed to 750mV. DB2000QL AC test load | 23 | |
| Output voltage low | VOL,AC | -100 | 100 | mV | 23 | ||
| Output max voltage (including overshoot) | Vmax,AC | 670 | 920 | mV | 23 | ||
| Output min voltage (including undershoot) | Vmin,AC | -100 | 100 | mV | 23 | ||
| Output voltage high | VOH,AC | 870 | 1020 | mV | Output swing programmed to 950mV | 23 | |
| Output max voltage (including overshoot) | Vmax,AC | 870 | 1120 | mV | 23 | ||
| Output voltage high with DC test load | VOH,DC | 225 | 270 | mV | DB2000QL DC test load | 23 | |
| Output voltage low with DC test load | VOL,DC | 10 | 150 | mV | 23 | ||
| Output overshoot voltage with DC test load | Vovs,DC | 75 | mV | 23 | |||
| Output undershoot voltage with DC test load | Vuds,DC | -75 | mV | 23 | |||
| Differential output impedance | Zdiff | 80.75 | 85 | 89.25 | Ω | Measured at VOL/VOH, VDD = 3.3V | 23 |
| Differential output impedance | Zdiff | 81 | 85 | 90 | Ω | Measured at VOL/VOH, VDD = 1.8V | 23 |
| Differential output impedance - crossing | Zdiff-crossing | 68 | 85 | 102 | Ω | Measured during transition | 23 |
| Output slew rate | dV/dt | 1.5 | 2.2 | V/ns | Measured from -150mV to +150mV on the differential waveform. Lowest slew rate | 23 | |
| Output slew rate | dV/dt | 1.8 | 2.6 | V/ns | Measured from -150mV to +150mV on the differential waveform. Low slew rate | 23 | |
| Output slew rate | dV/dt | 2 | 2.9 | V/ns | Measured from -150mV to +150mV on the differential waveform. High slew rate (default) | 23 | |
| Output slew rate | dV/dt | 2.4 | 4 | V/ns | Measured from -150mV to +150mV on the differential waveform. Highest slew rate | 23 | |
| Rising edge rate to falling edge rate matching DB2000QL AC test load | ∆dV/dt | 10 | % | 23 | |||
| Duty cycle distortion | DCD | -1 | 1 | % | Measured on the differential waveform. Input duty cycle = 50% | 23 | |
| Absolute crossing point voltage | Vcross,AC | 250 | 550 | mV | DB2000QL AC test load | 23 | |
| Absolute crossing point voltage | Vcross,DC | 130 | 200 | mV | DB2000QL DC test load | 23 | |
| Variation of Vcross over all clock edges | ∆Vcross,AC | 140 | mV | DB2000QL AC test load | 23 | ||
| Absolute value of ring back voltage as defined in PCIe | /VRB/ | 100 | mV | DB2000QL AC test load | 23 | ||
| Output voltage low | VOL | -120 | 120 | mV | 26 | ||
| Output voltage high | VOH | 780 | 980 | mV | Output swing programmed to 900mV. f0 = 156.25MHz or 312.5MHz | 26 | |
| Rise/fall time on single-ended waveform, 20% to 80% | tR, tF | 340 | ps | Output swing programmed to 800mV. Fastest slew rate. f0 = 156.25MHz or 312.5MHz | 26 | ||
| Operating frequency | f0 | 1 | 400 | MHz | Automatic Output Disable functionality is disabled | 26 | |
| Startup time | tstartup | 0.4 | ms | Cold start, f0 ≥ 100MHz | 26 | ||
| Output enable/disable time | tOE | 4 | 10 | clk | Time elapsed from OE assertion/deassertion to output clock starts/stops | 26 | |
| LOS# assertion time | tLOS-assert | 120 | ns | Time elapsed from loss of input clock to LOS# assertion. f0 < 100MHz | 26 | ||
| LOS# deassertion time | tLOS-deassert | 340 | ns | Time elapsed from presence of input clock to LOS# deassertion. f0 < 100MHz | 26 | ||
| Output-to-output skew | tskew | 50 | ps | Same bank | 27 | ||
| Total supply current LMKDB1108 | IDD,total | 85.7 | mA | All outputs running, f0 = 100MHz | 30 | ||
| Core supply current LMKDB1108 | IDD,core | 36.3 | mA | Pin PWRGD/PWRDN# = high, all outputs disabled | 31 | ||
| Power down current LMKDB1108 | IPD | 5.6 | mA | Pin PWRGD/PWRDN# = low | 31 | ||
| Junction-to-ambient thermal resistance (RKP0040 VQFN) | RθJA | 33.6 | °C/W | RKP0040 (VQFN), 40 pins | 22 | ||
| Junction-to-case (top) thermal resistance (RKP0040 VQFN) | RθJC(top) | 24.6 | °C/W | RKP0040 (VQFN), 40 pins | 22 | ||
| Junction-to-board thermal resistance (RKP0040 VQFN) | RθJB | 13.8 | °C/W | RKP0040 (VQFN), 40 pins | 22 | ||
| Junction-to-top characterization parameter (RKP0040 VQFN) | ΨJT | 0.4 | °C/W | RKP0040 (VQFN), 40 pins | 22 | ||
| Junction-to-board characterization parameter (RKP0040 VQFN) | ΨJB | 13.7 | °C/W | RKP0040 (VQFN), 40 pins | 22 | ||
| Junction-to-case (bottom) thermal resistance (RKP0040 VQFN) | RθJC(bot) | 4.2 | °C/W | RKP0040 (VQFN), 40 pins | 22 |
CAD (KiCad official)
- Symbol:
LMKDB1108Z85RKPR - Footprint:
Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm - 3D model: VQFN-40(5x5) (KiCad packages3D, STEP)
- 3D model files:
lmkdb1108z85rkpr-etched.step/lmkdb1108z85rkpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmkdb1108z85rkpr.step/lmkdb1108z85rkpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (129 pp, sha256
86848eb78ae2d928, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LMKDB1108Z85RKPR
**Texas Instruments** · IC · VQFN-40(5x5)
LMKDB1108Z85RKPR from Texas Instruments, in a VQFN-40(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LOS# | output | Open-drain loss-of-input-clock status output, requires an external pullup resistor; low = invalid input clock, high = valid input clock. |
| 2 | ^SLEWRATE_SEL | input | LP-HCSL output slew rate select input with internal pullup; low = slow slew rate, high = fast slew rate. |
| 3 | ^vSADR1_tri | input | SMBus address 3-level input with internal pullup and pulldown resistors. |
| 4 | ^vSADR0_tri | input | SMBus address 3-level input with internal pullup and pulldown resistors. |
| 5 | SMB_DATA | bidirectional | SMBus data line, requires an external pullup resistor, no connect if unused. |
| 6 | SMB_CLK | input | SMBus clock input, requires an external pullup resistor, no connect if unused. |
| 7 | VDDA | power_in | Analog power supply; additional power supply filtering is recommended (see Section 10.3). |
| 8 | CLKIN_P | input | Positive side of the differential clock input. |
| 9 | CLKIN_N | input | Negative side of the differential clock input. |
| 10 | VDDCLK | power_in | Output power supply. |
| 11 | vSBI_EN | input | SBI enable input with internal pulldown, state must not be changed after power-up; low at power-up = SBI disabled, high at power-up = SBI enabled with SMBus and other OE pins remaining functional. |
| 12 | vPWRGD/PWRDN# | input | Multifunction input with internal pulldown that acts as power good on the first low-to-high transition and as active-low power down afterwards (low = power-down mode, high = normal operation). |
| 13 | VDDCLK | power_in | Output power supply. |
| 14 | vOE0#/SHFT_LD# | input | Active-low output enable for CLK0 (0 = active, 1 = inactive) or SBI active-low shift register load input depending on SBI_EN, with internal pulldown. |
| 15 | CLK0_P | output | LP-HCSL differential clock output 0 positive, no connect if unused. |
| 16 | CLK0_N | output | LP-HCSL differential clock output 0 negative, no connect if unused. |
| 17 | CLK1_P | output | LP-HCSL differential clock output 1 positive, no connect if unused. |
| 18 | CLK1_N | output | LP-HCSL differential clock output 1 negative, no connect if unused. |
| 19 | vOE1#/SBI_IN | input | Active-low output enable for CLK1 (0 = active, 1 = inactive) or SBI data input depending on SBI_EN, with internal pulldown. |
| 20 | VDDCLK | power_in | Output power supply. |
| 21 | vOE2# | input | Active-low output enable for CLK2 with internal pulldown; 0 = output active, 1 = output inactive. |
| 22 | CLK2_P | output | LP-HCSL differential clock output 2 positive, no connect if unused. |
| 23 | CLK2_N | output | LP-HCSL differential clock output 2 negative, no connect if unused. |
| 24 | CLK3_P | output | LP-HCSL differential clock output 3 positive, no connect if unused. |
| 25 | CLK3_N | output | LP-HCSL differential clock output 3 negative, no connect if unused. |
| 26 | VDDCLK | power_in | Output power supply. |
| 27 | vOE3# | input | Active-low output enable for CLK3 with internal pulldown; 0 = output active, 1 = output inactive. |
| 28 | CLK4_P | output | LP-HCSL differential clock output 4 positive, no connect if unused. |
| 29 | CLK4_N | output | LP-HCSL differential clock output 4 negative, no connect if unused. |
| 30 | vOE4#/SBI_CLK | input | Active-low output enable for CLK4 (0 = active, 1 = inactive) or SBI clock input depending on SBI_EN, with internal pulldown. |
| 31 | CLK5_P | output | LP-HCSL differential clock output 5 positive, no connect if unused. |
| 32 | CLK5_N | output | LP-HCSL differential clock output 5 negative, no connect if unused. |
| 33 | vOE5# | input | Active-low output enable for CLK5 with internal pulldown; 0 = output active, 1 = output inactive. |
| 34 | vOE6#/SBI_OUT | bidirectional | Active-low output enable input for CLK6 (0 = active, 1 = inactive) or SBI shift register data output depending on SBI_EN, with internal pulldown. |
| 35 | CLK6_P | output | LP-HCSL differential clock output 6 positive, no connect if unused. |
| 36 | CLK6_N | output | LP-HCSL differential clock output 6 negative, no connect if unused. |
| 37 | VDDCLK | power_in | Output power supply. |
| 38 | CLK7_P | output | LP-HCSL differential clock output 7 positive, no connect if unused. |
| 39 | CLK7_N | output | LP-HCSL differential clock output 7 negative, no connect if unused. |
| 40 | vOE7# | input | Active-low output enable for CLK7 with internal pulldown; 0 = output active, 1 = output inactive. |
| 41 | Thermal Pad (GND) | power_in | Device ground, thermal pad. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-40(5x5) |
| Category | |
| Pins | 41 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDx Supply voltage on any VDD pin | VDDx | -0.3 | | 3.63 | V | | 22 |
| VIN Input voltage on CLKIN and digital input pins | VIN | -0.3 | | 3.63 | V | | 22 |
| Output current - continuous (CLKOUT) | IOUT | | | 30 | mA | | 22 |
| Output current - continuous (SMB_DATA, SBI_OUT) | IOUT | | | 25 | mA | | 22 |
| Output current - surge (CLKOUT) | IOUT | | | 60 | mA | | 22 |
| Output current - surge (SMB_DATA, SBI_OUT) | IOUT | | | 50 | mA | | 22 |
| Storage temperature | TS | -65 | | 150 | ℃ | | 22 |
| Junction temperature | TJ | | | 125 | °C | | 22 |
| Ambient temperature | TA | -40 | | 105 | °C | | 22 |
| Power supply voltage (3.3 V row) | VDD | 2.97 | 3.3 | 3.6 | V | | 22 |
| Power supply voltage (1.8 V row) | VDD | 1.71 | 1.8 | 1.89 | V | | 22 |
| Input voltage on CLKIN and digital input pins (recommended) | VIN | -0.3 | | 3.6 | V | | 22 |
| Power ramping time | tramp | 0.05 | | 5 | ms | | 22 |
| Clock input crossing point voltage | VIN,cross | 100 | | 1400 | mV | | 23 |
| Clock input duty cycle | DCIN | 45 | | 55 | % | | 23 |
| Differential clock input amplitude (half of differential peak-peak voltage) | VIN | 200 | | 2000 | mV | f0 ≤ 300MHz | 23 |
| Differential clock input amplitude (half of differential peak-peak voltage) | VIN | 250 | | 2000 | mV | 300MHz < f0 ≤ 400MHz | 23 |
| Output voltage high | VOH,AC | 670 | | 820 | mV | Output swing programmed to 750mV. DB2000QL AC test load | 23 |
| Output voltage low | VOL,AC | -100 | | 100 | mV | | 23 |
| Output max voltage (including overshoot) | Vmax,AC | 670 | | 920 | mV | | 23 |
| Output min voltage (including undershoot) | Vmin,AC | -100 | | 100 | mV | | 23 |
| Output voltage high | VOH,AC | 870 | | 1020 | mV | Output swing programmed to 950mV | 23 |
| Output max voltage (including overshoot) | Vmax,AC | 870 | | 1120 | mV | | 23 |
| Output voltage high with DC test load | VOH,DC | 225 | | 270 | mV | DB2000QL DC test load | 23 |
| Output voltage low with DC test load | VOL,DC | 10 | | 150 | mV | | 23 |
| Output overshoot voltage with DC test load | Vovs,DC | | | 75 | mV | | 23 |
| Output undershoot voltage with DC test load | Vuds,DC | -75 | | | mV | | 23 |
| Differential output impedance | Zdiff | 80.75 | 85 | 89.25 | Ω | Measured at VOL/VOH, VDD = 3.3V | 23 |
| Differential output impedance | Zdiff | 81 | 85 | 90 | Ω | Measured at VOL/VOH, VDD = 1.8V | 23 |
| Differential output impedance - crossing | Zdiff-crossing | 68 | 85 | 102 | Ω | Measured during transition | 23 |
| Output slew rate | dV/dt | 1.5 | | 2.2 | V/ns | Measured from -150mV to +150mV on the differential waveform. Lowest slew rate | 23 |
| Output slew rate | dV/dt | 1.8 | | 2.6 | V/ns | Measured from -150mV to +150mV on the differential waveform. Low slew rate | 23 |
| Output slew rate | dV/dt | 2 | | 2.9 | V/ns | Measured from -150mV to +150mV on the differential waveform. High slew rate (default) | 23 |
| Output slew rate | dV/dt | 2.4 | | 4 | V/ns | Measured from -150mV to +150mV on the differential waveform. Highest slew rate | 23 |
| Rising edge rate to falling edge rate matching DB2000QL AC test load | ∆dV/dt | | | 10 | % | | 23 |
| Duty cycle distortion | DCD | -1 | | 1 | % | Measured on the differential waveform. Input duty cycle = 50% | 23 |
| Absolute crossing point voltage | Vcross,AC | 250 | | 550 | mV | DB2000QL AC test load | 23 |
| Absolute crossing point voltage | Vcross,DC | 130 | | 200 | mV | DB2000QL DC test load | 23 |
| Variation of Vcross over all clock edges | ∆Vcross,AC | | | 140 | mV | DB2000QL AC test load | 23 |
| Absolute value of ring back voltage as defined in PCIe | /VRB/ | | | 100 | mV | DB2000QL AC test load | 23 |
| Output voltage low | VOL | -120 | | 120 | mV | | 26 |
| Output voltage high | VOH | 780 | | 980 | mV | Output swing programmed to 900mV. f0 = 156.25MHz or 312.5MHz | 26 |
| Rise/fall time on single-ended waveform, 20% to 80% | tR, tF | | | 340 | ps | Output swing programmed to 800mV. Fastest slew rate. f0 = 156.25MHz or 312.5MHz | 26 |
| Operating frequency | f0 | 1 | | 400 | MHz | Automatic Output Disable functionality is disabled | 26 |
| Startup time | tstartup | | | 0.4 | ms | Cold start, f0 ≥ 100MHz | 26 |
| Output enable/disable time | tOE | 4 | | 10 | clk | Time elapsed from OE assertion/deassertion to output clock starts/stops | 26 |
| LOS# assertion time | tLOS-assert | | | 120 | ns | Time elapsed from loss of input clock to LOS# assertion. f0 < 100MHz | 26 |
| LOS# deassertion time | tLOS-deassert | | | 340 | ns | Time elapsed from presence of input clock to LOS# deassertion. f0 < 100MHz | 26 |
| Output-to-output skew | tskew | | | 50 | ps | Same bank | 27 |
| Total supply current LMKDB1108 | IDD,total | | | 85.7 | mA | All outputs running, f0 = 100MHz | 30 |
| Core supply current LMKDB1108 | IDD,core | | | 36.3 | mA | Pin PWRGD/PWRDN# = high, all outputs disabled | 31 |
| Power down current LMKDB1108 | IPD | | | 5.6 | mA | Pin PWRGD/PWRDN# = low | 31 |
| Junction-to-ambient thermal resistance (RKP0040 VQFN) | RθJA | | 33.6 | | °C/W | RKP0040 (VQFN), 40 pins | 22 |
| Junction-to-case (top) thermal resistance (RKP0040 VQFN) | RθJC(top) | | 24.6 | | °C/W | RKP0040 (VQFN), 40 pins | 22 |
| Junction-to-board thermal resistance (RKP0040 VQFN) | RθJB | | 13.8 | | °C/W | RKP0040 (VQFN), 40 pins | 22 |
| Junction-to-top characterization parameter (RKP0040 VQFN) | ΨJT | | 0.4 | | °C/W | RKP0040 (VQFN), 40 pins | 22 |
| Junction-to-board characterization parameter (RKP0040 VQFN) | ΨJB | | 13.7 | | °C/W | RKP0040 (VQFN), 40 pins | 22 |
| Junction-to-case (bottom) thermal resistance (RKP0040 VQFN) | RθJC(bot) | | 4.2 | | °C/W | RKP0040 (VQFN), 40 pins | 22 |
## CAD (KiCad official)
- Symbol: `LMKDB1108Z85RKPR`
- Footprint: `Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm`
- 3D model: VQFN-40(5x5) (KiCad packages3D, STEP)
- 3D model files: `lmkdb1108z85rkpr-etched.step` / `lmkdb1108z85rkpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmkdb1108z85rkpr.step` / `lmkdb1108z85rkpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lmkdb1104.pdf?ts=1769591464437&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FLMKDB1104%252Fpart-details%252FLMKDB1104Z100REXT) (129 pp, sha256 `86848eb78ae2d928`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lmkdb1108z85rkpr-datasheet.pdf)