Generated by kicad-footprint-generator · KiCad file format 20260206
LMK05318BRGZR
Texas Instruments · Clock Jitter Cleaners & Synchronizers · VQFN-48(7x7)
LMK05318BRGZR from Texas Instruments, in a VQFN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STATUS0 | bidirectional | Status output 0 with programmable status signal, driver type (3.3V LVCMOS or open-drain) and polarity; leave floating if unused. |
| 2 | STATUS1/FDEC | bidirectional | Status output 1 with programmable signal, driver type and polarity; in I2C mode it can serve as the DCO frequency-decrement (FDEC) input; leave floating if unused. |
| 3 | CAP_DIG | passive | External LDO bypass capacitor for the digital core logic; recommended 10µF placed close to the pin. |
| 4 | VDD_DIG | power_in | 3.3V core supply for PLL1, PLL2 and digital blocks; recommended 1µF capacitor placed close to the pin. |
| 5 | VDD_IN | power_in | 3.3V core supply for the PRIREF and SECREF inputs; recommended 10µF capacitor placed close to the pin. |
| 6 | PRIREF_P | input | DPLL primary reference clock input (positive), differential or single-ended with programmable AC/DC-coupled termination; unused pair may float. |
| 7 | PRIREF_N | input | DPLL primary reference clock input (negative); pull to ground for single-ended LVCMOS on the P input; unused pair may float. |
| 8 | REFSEL | input | Manual DPLL reference selection, 3-level 1.8V-compatible input: 0 = PRIREF, 1 = SECREF, float or VIM = automatic selection; float if unused. |
| 9 | HW_SW_CTRL | input | Device start-up mode select, 3-level 1.8V-compatible input sampled only at power-on reset (0 = EEPROM+I2C, float = EEPROM+SPI, 1 = I2C+ROM). |
| 10 | SECREF_P | input | DPLL secondary reference clock input (positive), differential or single-ended with programmable AC/DC-coupled termination; unused pair may float. |
| 11 | SECREF_N | input | DPLL secondary reference clock input (negative); pull to ground for single-ended LVCMOS on the P input; unused pair may float. |
| 12 | GPIO0/SYNCN | input | Multi-function logic pin; output SYNC input (active low), externally pulled up if unused. |
| 13 | PDN | input | Active-low device power-down; low holds a hard reset with all blocks including serial interface powered down, high starts device per HW_SW_CTRL; internal 200kΩ pull-up to VDD_IN. |
| 14 | OUT0_P | output | Clock output 0 positive, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 15 | OUT0_N | output | Clock output 0 negative, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 16 | OUT1_N | output | Clock output 1 negative, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 17 | OUT1_P | output | Clock output 1 positive, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 18 | VDDO_01 | power_in | Output supply (1.8V, 2.5V or 3.3V) for OUT0 and OUT1; 0.1µF capacitor close to pin; may float if outputs unused. |
| 19 | VDDO_23 | power_in | Output supply (1.8V, 2.5V or 3.3V) for OUT2 and OUT3; 0.1µF capacitor close to pin; may float if outputs unused. |
| 20 | OUT2_P | output | Clock output 2 positive, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 21 | OUT2_N | output | Clock output 2 negative, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 22 | OUT3_N | output | Clock output 3 negative, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 23 | OUT3_P | output | Clock output 3 positive, programmable AC-LVDS, AC-CML, AC-LVPECL or HCSL driver; terminate or disable by register if unused. |
| 24 | GPIO1/SCS | input | Multi-function logic pin; I2C address LSB select (low = 00b, float = 01b, high = 10b) sampled at POR, or SPI chip select (SCS) in SPI mode. |
| 25 | SDA/SDI | bidirectional | I2C serial data I/O (open-drain, needs external pull-up) or SPI serial data input (SDI). |
| 26 | SCL/SCK | input | I2C serial clock input (open-drain, needs external pull-up) or SPI serial clock input (SCK). |
| 27 | VDD_PLL1 | power_in | 3.3V core supply for PLL1; recommended 10µF capacitor placed close to the pin. |
| 28 | CAP_PLL1 | passive | External LDO bypass capacitor for APLL1; recommended 10µF placed close to the pin. |
| 29 | LF1 | passive | External loop filter capacitor for APLL1 to ground; recommended 0.47µF (APLL LBW = 1.0kHz). |
| 30 | GPIO2/SDO/FINC | bidirectional | Multi-function logic pin; SPI data output (SDO) in SPI mode or DPLL DCO frequency-increment (FINC) input, active high, in I2C mode. |
| 31 | XO_P | input | XO/TCXO/OCXO input (positive), differential or single-ended (LVCMOS up to 2.5V) with programmable termination; input range 10 to 100MHz. |
| 32 | XO_N | input | XO/TCXO/OCXO input (negative); pull to ground for single-ended LVCMOS on the P input. |
| 33 | VDD_XO | power_in | 3.3V core supply for the XO input; recommended 10µF capacitor placed close to the pin. |
| 34 | LF2 | passive | External loop filter capacitor for APLL2 to ground; recommended 0.1µF (APLL LBW = 500kHz). |
| 35 | CAP_PLL2 | passive | External LDO bypass capacitor for APLL2; recommended 10µF placed close to the pin. |
| 36 | VDD_PLL2 | power_in | 3.3V core supply for PLL2; recommended 10µF capacitor placed close to the pin. |
| 37 | VDDO_4 | power_in | Output supply (1.8V, 2.5V or 3.3V) for OUT4; 0.1µF capacitor close to pin; may float if output unused. |
| 38 | OUT4_N | output | Clock output 4 negative, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver; terminate or disable by register if unused. |
| 39 | OUT4_P | output | Clock output 4 positive, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver; terminate or disable by register if unused. |
| 40 | VDDO_5 | power_in | Output supply (1.8V, 2.5V or 3.3V) for OUT5; 0.1µF capacitor close to pin; may float if output unused. |
| 41 | OUT5_N | output | Clock output 5 negative, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver; terminate or disable by register if unused. |
| 42 | OUT5_P | output | Clock output 5 positive, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver; terminate or disable by register if unused. |
| 43 | VDDO_6 | power_in | Output supply (1.8V, 2.5V or 3.3V) for OUT6; 0.1µF capacitor close to pin; may float if output unused. |
| 44 | OUT6_N | output | Clock output 6 negative, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver; terminate or disable by register if unused. |
| 45 | OUT6_P | output | Clock output 6 positive, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver; terminate or disable by register if unused. |
| 46 | VDDO_7 | power_in | Output supply (1.8V, 2.5V or 3.3V) for OUT7; 0.1µF capacitor close to pin; may float if output unused. |
| 47 | OUT7_N | output | Clock output 7 negative, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver (supports 1PPS output); terminate or disable by register if unused. |
| 48 | OUT7_P | output | Clock output 7 positive, programmable AC-LVDS, AC-CML, AC-LVPECL, HCSL or 1.8V LVCMOS driver (supports 1PPS output); terminate or disable by register if unused. |
| 49 | GND | power_in | Ground/thermal exposed pad; connect to PCB ground with at least a 5x5 via array for electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-48(7x7) |
| Category | RTC/Clock Chip |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Core supply voltage | VDD | 3.135 | 3.3 | 3.465 | V | 8 | |
| Output supply voltage (AC-LVDS/AC-CML/AC-LVPECL/HCSL) 1.8V | VDDO_x | 1.71 | 1.8 | 1.89 | V | AC-LVDS, AC-CML, AC-LVPECL or HCSL driver | 8 |
| Output supply voltage 2.5V | VDDO_x | 2.375 | 2.5 | 2.625 | V | AC-LVDS, AC-CML, AC-LVPECL or HCSL driver | 8 |
| Output supply voltage 3.3V | VDDO_x | 3.135 | 3.3 | 3.465 | V | AC-LVDS, AC-CML, AC-LVPECL or HCSL driver | 8 |
| Output supply voltage 1.8V LVCMOS | VDDO_x | 1.71 | 1.8 | 1.89 | V | 1.8V LVCMOS driver | 8 |
| Input voltage range clock and logic inputs | VIN | 0 | 3.465 | V | 8 | ||
| Ambient operating temperature | TA | -40 | 85 | °C | 8 | ||
| Junction temperature | TJ | 125 | °C | 8 | |||
| Power supply ramp time | tVDD | 0.01 | 100 | ms | 8 | ||
| EEPROM programming cycles | nEEcyc | 100 | cycles | 8 | |||
| Core supply voltage | VDD | -0.3 | 3.6 | V | 8 | ||
| Output supply voltage | VDDO | -0.3 | 3.6 | V | 8 | ||
| Junction temperature | TJ | 150 | °C | 8 | |||
| Storage temperature range | Tstg | -65 | 150 | °C | 8 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | ANSI/ESDA/JEDEC JS-001, all pins | 8 | |
| ESD CDM | V(ESD) | -750 | 750 | V | ANSI/ESDA/JEDEC JS-002, all pins | 8 | |
| Total current consumption, power down | IDDPDN | 56 | 75 | mA | Device powered down (PDN pin held low) | 10 | |
| XO input frequency range | fIN | 10 | 100 | MHz | 10 | ||
| XO single-ended input voltage swing | VIN-SE | 0.4 | 2.6 | Vpp | Single-ended input, internally AC coupled | 10 | |
| XO differential input peak-to-peak swing | VIN-DIFF | 0.4 | 2 | Vpp | Differential input | 10 | |
| XO differential input voltage swing | VID | 0.2 | 1 | /V/ | Differential input | 10 | |
| XO input duty cycle | IDC | 40 | 60 | % | 10 | ||
| XO input leakage | IIN | -350 | 350 | µA | 50Ω and 100Ω internal termination disabled | 10 | |
| Reference input frequency, differential | fIN | 5 | 800 | MHz | Differential input | 10 | |
| Reference single-ended input swing | VIN-SE | 0.4 | 2.6 | Vpp | AC-coupled input | 10 | |
| Reference differential swing Vpp | VIN-DIFF | 0.4 | 2 | Vpp | Differential input, VHYST = 50mV | 10 | |
| Reference differential swing Vpp | VIN-DIFF | 0.7 | 2 | Vpp | Differential input, VHYST = 200mV | 10 | |
| Reference differential voltage swing | VID | 0.2 | 1 | V | Differential input, VHYST = 50mV | 10 | |
| Reference differential voltage swing | VID | 0.35 | 1 | V | Differential input, VHYST = 200mV | 10 | |
| Reference input leakage | IIN | -350 | 350 | µA | 50Ω and 100Ω internal termination disabled | 10 | |
| VCO1 frequency range | fVCO1 | 2499.75 | 2500 | 2500.25 | MHz | 10 | |
| VCO2 frequency range | fVCO2 | 5500 | 6250 | MHz | 10 | ||
| Allowable temperature drift for continuous lock | /ΔTCL/ | 125 | °C | After programming lock, output configuration must not be changed to provide continuous lock | 10 | ||
| Reference input high voltage | VIH | 1.8 | V | DC-coupled input | 10 | ||
| Reference input low voltage | VIL | 0.6 | V | DC-coupled input | 10 | ||
| Core current VDD_DIG | IDD_DIG | 21 | mA | 9 | |||
| Core current VDD_IN | IDD_IN | 43 | mA | 9 | |||
| Core current VDD_PLL1 | IDD_PLL1 | 110 | mA | DPLL and APLL1 enabled | 9 | ||
| Core current VDD_XO | IDD_XO | 20 | mA | 9 | |||
| Core current VDD_PLL2, APLL2 disabled | IDD_PLL2 | 18.5 | mA | APLL2 disabled | 9 | ||
| Core current VDD_PLL2, APLL2 enabled | IDD_PLL2 | 120 | mA | APLL2 enabled | 9 | ||
| Output current, mux+divider, divider 2 to 6 | IDDO_x | 65 | mA | Output mux and divider enabled, excluding driver, divider value = 2 to 6 | 10 | ||
| Output current, mux+divider, divider >6 | IDDO_x | 70 | mA | Output mux and divider enabled, excluding driver, divider value > 6 | 10 | ||
| Output driver current AC-LVDS | IDDO_x | 11 | mA | AC-LVDS | 10 | ||
| Output driver current AC-CML | IDDO_x | 16 | mA | AC-CML | 10 | ||
| Output driver current AC-LVPECL | IDDO_x | 18 | mA | AC-LVPECL | 10 | ||
| Output driver current HCSL | IDDO_x | 25 | mA | HCSL, 50Ω load to GND | 10 | ||
| Output driver current 1.8V LVCMOS | IDDO_x | 4.7 | mA | 1.8V LVCMOS (x2), 100MHz | 10 | ||
| Junction-to-ambient thermal resistance (4-layer JEDEC) | RθJA | 23.3 | °C/W | RGZ (VQFN) 48 pin | 9 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 13.2 | °C/W | 4-layer JEDEC | 9 | ||
| Junction-to-board thermal resistance | RθJB | 7.4 | °C/W | 4-layer JEDEC | 9 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.4 | °C/W | 4-layer JEDEC | 9 | ||
| Junction-to-top characterization parameter | ψJT | 0.2 | °C/W | 4-layer JEDEC | 9 | ||
| Junction-to-board characterization parameter | ψJB | 7.3 | °C/W | 4-layer JEDEC | 9 | ||
| Junction-to-ambient thermal resistance (10-layer custom PCB) | RθJA | 9.1 | °C/W | 10-layer custom PCB | 9 | ||
| Junction-to-board thermal resistance (10-layer) | RθJB | 4.4 | °C/W | 10-layer custom PCB | 9 | ||
| Junction-to-board characterization parameter (10-layer) | ψJB | 4.4 | °C/W | 10-layer custom PCB | 9 |
CAD (KiCad official)
- Symbol:
LMK05318BRGZR - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: VQFN-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
lmk05318brgzr-etched.step/lmk05318brgzr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmk05318brgzr.step/lmk05318brgzr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (99 pp, sha256
131cbf173c63a64c, retrieved 2026-10-30, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).