Generated by kicad-footprint-generator · KiCad file format 20260206
LMK04826BISQX
Texas Instruments · Clock Generators / Frequency Synthesizers / PLL · WQFN-64-EP(9x9)
LMK04826BISQX from Texas Instruments, in a WQFN-64-EP(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DCLKout0 | output | Device clock output 0 is a differential clock output in clock group 0; keep outputs in the group at the same frequency or at frequencies without spurious interference, and set the output format buffer to powerdown with the pins floating if unused. |
| 2 | DCLKout0* | output | Complementary pin of differential device clock output 0 in clock group 0; set the output format buffer to powerdown and leave both pins floating if unused. |
| 3 | SDCLKout1 | output | SYSREF / device clock output 1 is a differential clock output in clock group 0; keep outputs in the group at the same frequency or at frequencies without spurious interference, and power down the output buffer with pins floating if unused. |
| 4 | SDCLKout1* | output | Complementary pin of differential SYSREF / device clock output 1 in clock group 0; set the output format buffer to powerdown and leave both pins floating if unused. |
| 5 | RESET/GPO | bidirectional | Device reset input or general-purpose output; as a reset input the polarity and nominal 160-kΩ pull-up or pull-down are register-controlled, and as an output it can be push-pull or open-drain. |
| 6 | SYNC/SYSREF_REQ | input | Synchronization input that can reset dividers, trigger the SYSREF pulser, or request continuous SYSREF; polarity is register-controlled and it has a nominal 160-kΩ pulldown. |
| 7 | NC | unconnected | Do not connect; this pin must be left floating. |
| 8 | NC | unconnected | Do not connect; this pin must be left floating. |
| 9 | NC | unconnected | Do not connect; this pin must be left floating. |
| 10 | Vcc1_VCO | power_in | Power supply for the VCO LDO; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 11 | LDObyp1 | passive | LDO bypass pin that must be bypassed to ground with a 10-µF capacitor placed close to the pin. |
| 12 | LDObyp2 | passive | LDO bypass pin that must be bypassed to ground with a 0.1-µF capacitor placed close to the pin. |
| 13 | SDCLKout3 | output | SYSREF / device clock output 3 is a differential clock output in clock group 1; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 14 | SDCLKout3* | output | Complementary pin of differential SYSREF / device clock output 3; set the output format buffer to powerdown and leave both pins floating if unused. |
| 15 | DCLKout2 | output | Device clock output 2 is a differential clock output in clock group 1; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 16 | DCLKout2* | output | Complementary pin of differential device clock output 2; set the output format buffer to powerdown and leave both pins floating if unused. |
| 17 | Vcc2_CG1 | power_in | Power supply for clock outputs 2 and 3; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 18 | CS* | input | Active-low SPI chip select that must be pulled up externally or actively driven high when not in use. |
| 19 | SCK | input | Active-high SPI clock input with a nominal 160-kΩ pulldown. |
| 20 | SDIO | bidirectional | SPI data pin that can be bidirectional; as an output it can be open-drain (requires external pull-up) or push-pull, and register settings can disable the output. |
| 21 | Vcc3_SYSREF | power_in | Power supply for the SYSREF divider and SYNC; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 22 | SDCLKout5 | output | SYSREF / device clock output 5 is a differential clock output in clock group 2; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 23 | SDCLKout5* | output | Complementary pin of differential SYSREF / device clock output 5; set the output format buffer to powerdown and leave both pins floating if unused. |
| 24 | DCLKout4 | output | Device clock output 4 is a differential clock output in clock group 2; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 25 | DCLKout4* | output | Complementary pin of differential device clock output 4; set the output format buffer to powerdown and leave both pins floating if unused. |
| 26 | Vcc4_CG2 | power_in | Power supply for clock outputs 4, 5, 6, and 7; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 27 | DCLKout6 | output | Device clock output 6 is a differential clock output in clock group 2; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 28 | DCLKout6* | output | Complementary pin of differential device clock output 6; set the output format buffer to powerdown and leave both pins floating if unused. |
| 29 | SDCLKout7 | output | SYSREF / device clock output 7 is a differential clock output in clock group 2; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 30 | SDCLKout7* | output | Complementary pin of differential SYSREF / device clock output 7; set the output format buffer to powerdown and leave both pins floating if unused. |
| 31 | Status_LD1 | bidirectional | Programmable status pin that by default is an active-high output showing PLL1 lock detect, with other status conditions and polarity register-selectable and open-drain or push-pull output. |
| 32 | CPout1 | output | Charge pump 1 output connected to the external PLL1 loop filter components and to the VCXO control voltage pin. |
| 33 | Vcc5_DIG | power_in | Power supply for digital circuitry such as the SPI bus and GPIO pins; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 34 | CLKin1 | input | Default reference clock input port 1 for PLL1 (shared with FBCLKin and Fin functions); can be DC or AC coupled, accepts single-ended or differential clocks, and if unused in single-ended use connect to GND with 0.1 µF. |
| 35 | CLKin1* | input | Complementary pin of CLKin1 (default reference clock input port 1 for PLL1, shared with FBCLKin* and Fin* functions); can be DC or AC coupled and accepts single-ended or differential clocks. |
| 36 | Vcc6_PLL1 | power_in | Power supply for PLL1, charge pump 1, and the holdover DAC; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 37 | CLKin0 | input | Reference clock input port 0 for PLL1 that can also serve as a synchronization input for SYNC/SYSREF; can be DC or AC coupled and accepts single-ended or differential clocks. |
| 38 | CLKin0* | input | Complementary pin of reference clock input port 0 for PLL1; can be DC or AC coupled and accepts single-ended or differential clocks. |
| 39 | Vcc7_OSCout | power_in | Power supply for the OSCout port and CLKin2; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 40 | OSCout | bidirectional | Default buffered output of the OSCin port that defaults to LVPECL, where only 240-Ω emitter resistors are supported; shared with CLKin2 reference input port 2 for PLL1, which must be configured as an input in registers. |
| 41 | OSCout* | bidirectional | Complementary pin of the buffered OSCin output, which defaults to LVPECL and supports only 240-Ω emitter resistors in LVPECL format; shared with CLKin2* reference input port 2 for PLL1. |
| 42 | Vcc8_OSCin | power_in | Power supply for OSCin; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 43 | OSCin | input | Feedback to PLL1 and reference input to PLL2; inputs should be AC-coupled, accepts single-ended or differential clocks, and unused single-ended input should connect to GND with 0.1 µF. |
| 44 | OSCin* | input | Complementary pin of OSCin; inputs should be AC-coupled and accepts single-ended or differential clocks. |
| 45 | Vcc9_CP2 | power_in | Power supply for the PLL2 charge pump; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 46 | CPout2 | output | Charge pump 2 output connected to the external PLL2 loop filter components and, when an external VCO is used, to its control voltage pin; do not route near noisy signals. |
| 47 | Vcc10_PLL2 | power_in | Power supply for PLL2; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 48 | Status_LD2 | bidirectional | Programmable status pin that by default is an active-high output showing PLL2 lock detect, with other status conditions and polarity register-selectable and open-drain or push-pull output. |
| 49 | SDCLKout9 | output | SYSREF / device clock 9 is a differential clock output in clock group 3; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 50 | SDCLKout9* | output | Complementary pin of differential SYSREF / device clock 9; set the output format buffer to powerdown and leave both pins floating if unused. |
| 51 | DCLKout8 | output | Device clock output 8 is a differential clock output in clock group 3; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 52 | DCLKout8* | output | Complementary pin of differential device clock output 8; set the output format buffer to powerdown and leave both pins floating if unused. |
| 53 | Vcc11_CG3 | power_in | Power supply for clock outputs 8, 9, 10, and 11; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 54 | DCLKout10 | output | Device clock output 10 is a differential clock output in clock group 3; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 55 | DCLKout10* | output | Complementary pin of differential device clock output 10; set the output format buffer to powerdown and leave both pins floating if unused. |
| 56 | SDCLKout11 | output | SYSREF / device clock output 11 is a differential clock output in clock group 3; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 57 | SDCLKout11* | output | Complementary pin of differential SYSREF / device clock output 11; set the output format buffer to powerdown and leave both pins floating if unused. |
| 58 | CLKin_SEL0 | bidirectional | Programmable status pin that by default is an active-high input with nominal 160-kΩ pulldown selecting the PLL1 reference CLKin in pin-select mode; as an output it can be push-pull or open-drain. |
| 59 | CLKin_SEL1 | bidirectional | Programmable status pin that by default is an active-high input with nominal 160-kΩ pulldown selecting the PLL1 reference CLKin in pin-select mode; as an output it can be push-pull or open-drain. |
| 60 | SDCLKout13 | output | SYSREF / device clock output 13 is a differential clock output in clock group 0; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 61 | SDCLKout13* | output | Complementary pin of differential SYSREF / device clock output 13; set the output format buffer to powerdown and leave both pins floating if unused. |
| 62 | DCLKout12 | output | Device clock output 12 is a differential clock output in clock group 0; keep outputs in the group at the same frequency and power down the buffer with pins floating if unused. |
| 63 | DCLKout12* | output | Complementary pin of differential device clock output 12; set the output format buffer to powerdown and leave both pins floating if unused. |
| 64 | Vcc12_CG0 | power_in | Power supply for clock outputs 0, 1, 12, and 13; decoupling requirements may change with system frequency, see Pin Connection Recommendations. |
| 65 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-64-EP(9x9) |
| Category | RTC/Clock Chip |
| Pins | 65 |
CAD (KiCad official)
- Symbol:
LMK04826BISQX - Footprint:
Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm - 3D model: WQFN-64-EP(9x9) (KiCad packages3D, STEP)
- 3D model files:
lmk04826bisqx-etched.step/lmk04826bisqx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmk04826bisqx.step/lmk04826bisqx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (128 pp, sha256
d8103cecc9ce9c26, retrieved 2026-10-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).