main
Ray
Publish 0.1.0
8a01d9a
LMK03318RHSR
Texas Instruments · Clock Generators / Frequency Synthesizers / PLL · WQFN-48-EP(7x7)
LMK03318RHSR from Texas Instruments, in a WQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STATUS0 | output | Status output 0, open drain requiring external pullup or 3.3-V LVCMOS push-pull output from synth, with programmable signal selection and polarity. |
| 2 | STATUS1 | output | Status output 1, open drain requiring external pullup or 3.3-V LVCMOS push-pull output from synth, with programmable signal selection and polarity. |
| 3 | CAP_DIG | passive | External bypass capacitor for digital blocks; attach 10 µF to GND. |
| 4 | VDD_DIG | power_in | 3.3 V power supply for digital control and STATUS outputs. |
| 5 | VDD_IN | power_in | 3.3 V power supply for input block. |
| 6 | PRIREF_P | input | Primary reference clock positive input accepting differential or single-ended signal, internally AC-coupled and biased; for LVCMOS input the non-driven pin must be pulled to ground. |
| 7 | PRIREF_N | input | Primary reference clock negative input accepting differential or single-ended signal, internally AC-coupled and biased; for LVCMOS input the non-driven pin must be pulled to ground. |
| 8 | REFSEL | input | Manual reference input selection for PLL (3-state LVCMOS) with weak pullup resistor. |
| 9 | HW_SW_CTRL | input | LVCMOS selection of Hard Pin Mode (ROM), Soft Pin Mode (EEPROM) or Register Default Mode, with weak pullup resistor. |
| 10 | SECREF_P | input | Secondary reference positive input accepting differential, single-ended or crystal input; LVCMOS swing must be attenuated to less than 2.6 V externally. |
| 11 | SECREF_N | input | Secondary reference negative input accepting differential, single-ended or crystal input; the non-driven pin must be pulled to ground for LVCMOS input. |
| 12 | GPIO0 | input | LVCMOS multifunction input (2-state): ROM page select in hard pin mode, active-low output synchronization in soft pin mode. |
| 13 | PDN | input | LVCMOS device power-down input, active low, with weak pullup resistor. |
| 14 | OUT0_P | output | Positive pin of universal output pair 0; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 15 | OUT0_N | output | Negative pin of universal output pair 0; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 16 | OUT1_N | output | Negative pin of universal output pair 1; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 17 | OUT1_P | output | Positive pin of universal output pair 1; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 18 | VDDO_01 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT0/OUT1 channel. |
| 19 | VDDO_23 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT2/OUT3 channel. |
| 20 | OUT2_P | output | Positive pin of universal output pair 2; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 21 | OUT2_N | output | Negative pin of universal output pair 2; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 22 | OUT3_N | output | Negative pin of universal output pair 3; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 23 | OUT3_P | output | Positive pin of universal output pair 3; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 24 | GPIO1 | input | LVCMOS multifunction input (3-state or 2-state); selects I2C slave address LSBs in soft pin mode. |
| 25 | SDA | bidirectional | I2C serial data (bidirectional, open drain) requiring an external pullup resistor to VDD_DIG. |
| 26 | SCL | bidirectional | I2C serial clock (bidirectional, open drain) requiring an external pullup resistor to VDD_DIG. |
| 27 | VDD_LDO | power_in | 3.3 V power supply for PLL LDO. |
| 28 | CAP_LDO | passive | External bypass capacitor for PLL LDO; attach 10 µF to GND. |
| 29 | NC | unconnected | No connect. |
| 30 | GPIO2 | input | LVCMOS multifunction input (3-state or 2-state); EEPROM page select in soft pin mode. |
| 31 | GPIO3 | input | LVCMOS multifunction input (3-state or 2-state); EEPROM page select in soft pin mode. |
| 32 | GPIO4 | input | LVCMOS multifunction input (2-state); frequency margining enable in soft pin mode. |
| 33 | GPIO5 | input | Multifunction input (2-state) or analog input for frequency margin. |
| 34 | LF | passive | External loop filter for PLL. |
| 35 | CAP_PLL | passive | External bypass capacitor for PLL; attach 10 µF to GND. |
| 36 | VDD_PLL | power_in | 3.3 V power supply for PLL/VCO. |
| 37 | VDDO_4 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT4 channel. |
| 38 | OUT4_N | output | Negative pin of universal output pair 4; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 39 | OUT4_P | output | Positive pin of universal output pair 4; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 40 | VDDO_5 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT5 channel. |
| 41 | OUT5_N | output | Negative pin of universal output pair 5; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 42 | OUT5_P | output | Positive pin of universal output pair 5; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 43 | VDDO_6 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT6 channel. |
| 44 | OUT6_N | output | Negative pin of universal output pair 6; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 45 | OUT6_P | output | Positive pin of universal output pair 6; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 46 | VDDO_7 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT7 channel. |
| 47 | OUT7_N | output | Negative pin of universal output pair 7; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 48 | OUT7_P | output | Positive pin of universal output pair 7; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-48-EP(7x7) |
| Category | RTC/Clock Chip |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (VDD_IN, VDD_PLL, VDD_LDO, VDD_DIG, VDDO_x) | VDD | -0.3 | 3.6 | V | 7 | ||
| Input voltage, clock and logic inputs | VIN | -0.3 | V | Max printed as VDD + 0.3 V | 7 | ||
| Output voltage, clock and logic outputs | VOUT | -0.3 | V | Max printed as VDD + 0.3 V | 7 | ||
| Junction temperature | TJ | 150 | °C | 7 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 7 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model, ANSI/ESDA/JEDEC JS-001 | 7 | |
| ESD CDM | V(ESD) | -500 | 500 | V | Charged-device model, JESD22-C101 | 7 | |
| Core supply voltage | VDD_IN, VDD_PLL, VDD_LDO, VDD_DIG | 3.135 | 3.3 | 3.465 | V | 8 | |
| Output driver supply voltage (NOM 1.8 V) | VDDO_x | 1.7 | 1.8 | 3.465 | V | Differential, LVCMOS | 8 |
| Output driver supply voltage (NOM 2.5 V) | VDDO_x | 1.7 | 2.5 | 3.465 | V | Differential, LVCMOS | 8 |
| Output driver supply voltage (NOM 3.3 V) | VDDO_x | 1.7 | 3.3 | 3.465 | V | Differential, LVCMOS | 8 |
| Ambient temperature | TA | -40 | 25 | 85 | °C | 8 | |
| Junction temperature | TJ | 125 | °C | 8 | |||
| Maximum VDD power-up ramp | dVDD/dt | 0.1 | 100 | ms | 8 | ||
| EEPROM number of writes | WR | 100 | writes | 8 | |||
| Junction-to-ambient thermal resistance | RθJA | 26.47 | °C/W | 4-layer JEDEC board, airflow 0 LFM | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 16.4 | °C/W | Airflow 200 LFM | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 14.62 | °C/W | Airflow 400 LFM | 8 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 16.57 | °C/W | Airflow 0 LFM | 8 | ||
| Junction-to-board thermal resistance | RθJB | 6.84 | °C/W | Airflow 0 LFM | 8 | ||
| Junction-to-board characterization parameter | ψJB | 4.02 | °C/W | Airflow 0 LFM | 8 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.06 | °C/W | Airflow 0 LFM | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 10 | °C/W | 10-layer 200 mm × 250 mm board, 36 thermal vias, Airflow = 0 LFM | 8 | ||
| Power-down current, total device | IDD-PD | 30 | 50 | mA | Power down (PDN = 0) | 9 | |
| Current consumption, VDD_IN | IDD_IN | 48 | 65 | mA | Per supply pin; test setup as printed, VDD = 3.3 V, VDDO_xx = 3.3 V, OUT[0-7] = 156.25 MHz LVPECL | 9 | |
| Current consumption, VDD_PLL | IDD_PLL | 128 | 158 | mA | Same test setup as IDD_IN | 9 | |
| Current consumption, VDD_LDO | IDD_LDO | 15 | 30 | mA | Same test setup as IDD_IN | 9 | |
| Current consumption, VDD_DIG | IDD_DIG | 19 | 38 | mA | Same test setup as IDD_IN | 9 | |
| Output supply current, VDDO_01 | IDDO_01 | 85 | 105 | mA | Same test setup as IDD_IN | 9 | |
| Output supply current, VDDO_23 | IDDO_23 | 85 | 105 | mA | Same test setup as IDD_IN | 9 | |
| Output supply current, VDDO_4 | IDDO_4 | 58 | 75 | mA | Same test setup as IDD_IN | 9 | |
| Crystal frequency (pullable) | fXTAL | 10 | 52 | MHz | Fundamental mode | 10 | |
| Crystal ESR (pullable) | ESR | 60 | Ω | fXTAL = 10 MHz to 16 MHz (50 Ω for 16-30 MHz, 30 Ω for 30-52 MHz) | 10 | ||
| Crystal maximum drive level | PXTAL | 300 | µW | 10 | |||
| On-chip XO input capacitance | CXO | 14 | 24 | pF | Single-ended, each pin referenced to GND | 10 | |
| Pulling range | fPR | -50 | 50 | ppm | Crystal C0/C1 < 250 | 10 | |
| Input frequency range | fCLK | 1 | 300 | MHz | 11 | ||
| LVCMOS input high voltage (PRI_REF) | VIH | 1.4 | V | PRI_REF; max printed as VDD_IN | 11 | ||
| LVCMOS input high voltage (SEC_REF) | VIH | 1.4 | 2.6 | V | SEC_REF | 11 | |
| LVCMOS input low voltage | VIL | 0 | 0.5 | V | 11 | ||
| Input voltage swing, differential peak-peak | VID,DIFF,PP | 0.2 | 2 | V | Differential input | 11 | |
| Input leakage current | IIN | -100 | 100 | µA | 11 | ||
| VCO frequency range | fVCO | 4.8 | 5.4 | GHz | 11 | ||
| Phase detector frequency | fPD | 1 | 150 | MHz | 12 | ||
| 1.8-V LVCMOS output frequency | fOUT | 1 | 200 | MHz | 12 | ||
| 1.8-V LVCMOS output high voltage | VOH | 1.35 | V | IOH = 1 mA | 12 | ||
| 1.8-V LVCMOS output low voltage | VOL | 0.35 | V | IOL = 1 mA | 12 | ||
| STATUS LVCMOS output high voltage | VOH | 2.5 | V | IOH = 1 mA | 12 | ||
| STATUS LVCMOS output low voltage | VOL | 0.6 | V | IOL = 1 mA | 12 | ||
| STATUS open-drain output low voltage | VOL | 0.6 | V | 13 | |||
| AC-LVPECL output frequency | fOUT | 1 | 1000 | MHz | 13 | ||
| AC-LVPECL output voltage swing | VOD | 500 | 800 | 1000 | mV | AC-coupled to 100-Ω differential load | 13 |
| AC-LVDS output voltage swing | VOD | 250 | 400 | 450 | mV | AC-coupled to 100-Ω differential load | 13 |
| AC-CML output voltage swing | VOD | 400 | 600 | 800 | mV | AC-coupled to 100-Ω differential load | 14 |
| HCSL output high voltage | VOH | 660 | 850 | mV | Outputs with 50 Ω // 2 pF to GND | 14 | |
| HCSL absolute crossing voltage | VCROSS | 250 | 550 | mV | Outputs with 50 Ω // 2 pF to GND | 14 | |
| Power-on reset threshold voltage | VTHRESH | 2.72 | 2.95 | V | 14 | ||
| 2-level logic input high voltage | VIH | 1.2 | V | HW_SW_CTRL, PDN, GPIO[5:0] | 15 | ||
| 2-level logic input low voltage | VIL | 0.6 | V | HW_SW_CTRL, PDN, GPIO[5:0] | 15 | ||
| I2C clock rate | fSCL | 100 | 400 | kHz | 16 | ||
| Closed-loop RMS phase jitter, 50-MHz crystal, integer-N | RJ | 100 | 150 | fs RMS | 50-MHz crystal, Integer-N PLL, fOUT = 156.25 MHz, all differential output types | 17 |
CAD (KiCad official)
- Symbol:
LMK03318RHSR - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: WQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
lmk03318rhsr-etched.step/lmk03318rhsr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmk03318rhsr.step/lmk03318rhsr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (143 pp, sha256
fa53e5cc6a892d69, retrieved 2026-10-30, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LMK03318RHSR
**Texas Instruments** · Clock Generators / Frequency Synthesizers / PLL · WQFN-48-EP(7x7)
LMK03318RHSR from Texas Instruments, in a WQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STATUS0 | output | Status output 0, open drain requiring external pullup or 3.3-V LVCMOS push-pull output from synth, with programmable signal selection and polarity. |
| 2 | STATUS1 | output | Status output 1, open drain requiring external pullup or 3.3-V LVCMOS push-pull output from synth, with programmable signal selection and polarity. |
| 3 | CAP_DIG | passive | External bypass capacitor for digital blocks; attach 10 µF to GND. |
| 4 | VDD_DIG | power_in | 3.3 V power supply for digital control and STATUS outputs. |
| 5 | VDD_IN | power_in | 3.3 V power supply for input block. |
| 6 | PRIREF_P | input | Primary reference clock positive input accepting differential or single-ended signal, internally AC-coupled and biased; for LVCMOS input the non-driven pin must be pulled to ground. |
| 7 | PRIREF_N | input | Primary reference clock negative input accepting differential or single-ended signal, internally AC-coupled and biased; for LVCMOS input the non-driven pin must be pulled to ground. |
| 8 | REFSEL | input | Manual reference input selection for PLL (3-state LVCMOS) with weak pullup resistor. |
| 9 | HW_SW_CTRL | input | LVCMOS selection of Hard Pin Mode (ROM), Soft Pin Mode (EEPROM) or Register Default Mode, with weak pullup resistor. |
| 10 | SECREF_P | input | Secondary reference positive input accepting differential, single-ended or crystal input; LVCMOS swing must be attenuated to less than 2.6 V externally. |
| 11 | SECREF_N | input | Secondary reference negative input accepting differential, single-ended or crystal input; the non-driven pin must be pulled to ground for LVCMOS input. |
| 12 | GPIO0 | input | LVCMOS multifunction input (2-state): ROM page select in hard pin mode, active-low output synchronization in soft pin mode. |
| 13 | PDN | input | LVCMOS device power-down input, active low, with weak pullup resistor. |
| 14 | OUT0_P | output | Positive pin of universal output pair 0; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 15 | OUT0_N | output | Negative pin of universal output pair 0; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 16 | OUT1_N | output | Negative pin of universal output pair 1; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 17 | OUT1_P | output | Positive pin of universal output pair 1; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 18 | VDDO_01 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT0/OUT1 channel. |
| 19 | VDDO_23 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT2/OUT3 channel. |
| 20 | OUT2_P | output | Positive pin of universal output pair 2; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 21 | OUT2_N | output | Negative pin of universal output pair 2; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 22 | OUT3_N | output | Negative pin of universal output pair 3; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 23 | OUT3_P | output | Positive pin of universal output pair 3; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 24 | GPIO1 | input | LVCMOS multifunction input (3-state or 2-state); selects I2C slave address LSBs in soft pin mode. |
| 25 | SDA | bidirectional | I2C serial data (bidirectional, open drain) requiring an external pullup resistor to VDD_DIG. |
| 26 | SCL | bidirectional | I2C serial clock (bidirectional, open drain) requiring an external pullup resistor to VDD_DIG. |
| 27 | VDD_LDO | power_in | 3.3 V power supply for PLL LDO. |
| 28 | CAP_LDO | passive | External bypass capacitor for PLL LDO; attach 10 µF to GND. |
| 29 | NC | unconnected | No connect. |
| 30 | GPIO2 | input | LVCMOS multifunction input (3-state or 2-state); EEPROM page select in soft pin mode. |
| 31 | GPIO3 | input | LVCMOS multifunction input (3-state or 2-state); EEPROM page select in soft pin mode. |
| 32 | GPIO4 | input | LVCMOS multifunction input (2-state); frequency margining enable in soft pin mode. |
| 33 | GPIO5 | input | Multifunction input (2-state) or analog input for frequency margin. |
| 34 | LF | passive | External loop filter for PLL. |
| 35 | CAP_PLL | passive | External bypass capacitor for PLL; attach 10 µF to GND. |
| 36 | VDD_PLL | power_in | 3.3 V power supply for PLL/VCO. |
| 37 | VDDO_4 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT4 channel. |
| 38 | OUT4_N | output | Negative pin of universal output pair 4; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 39 | OUT4_P | output | Positive pin of universal output pair 4; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 40 | VDDO_5 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT5 channel. |
| 41 | OUT5_N | output | Negative pin of universal output pair 5; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 42 | OUT5_P | output | Positive pin of universal output pair 5; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 43 | VDDO_6 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT6 channel. |
| 44 | OUT6_N | output | Negative pin of universal output pair 6; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 45 | OUT6_P | output | Positive pin of universal output pair 6; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 46 | VDDO_7 | power_in | 1.8 V, 2.5 V, or 3.3 V power supply for OUT7 channel. |
| 47 | OUT7_N | output | Negative pin of universal output pair 7; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 48 | OUT7_P | output | Positive pin of universal output pair 7; programmable differential or 2 x 1.8-V LVCMOS driver. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-48-EP(7x7) |
| Category | RTC/Clock Chip |
| Pins | 49 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (VDD_IN, VDD_PLL, VDD_LDO, VDD_DIG, VDDO_x) | VDD | -0.3 | | 3.6 | V | | 7 |
| Input voltage, clock and logic inputs | VIN | -0.3 | | | V | Max printed as VDD + 0.3 V | 7 |
| Output voltage, clock and logic outputs | VOUT | -0.3 | | | V | Max printed as VDD + 0.3 V | 7 |
| Junction temperature | TJ | | | 150 | °C | | 7 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 7 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | Human-body model, ANSI/ESDA/JEDEC JS-001 | 7 |
| ESD CDM | V(ESD) | -500 | | 500 | V | Charged-device model, JESD22-C101 | 7 |
| Core supply voltage | VDD_IN, VDD_PLL, VDD_LDO, VDD_DIG | 3.135 | 3.3 | 3.465 | V | | 8 |
| Output driver supply voltage (NOM 1.8 V) | VDDO_x | 1.7 | 1.8 | 3.465 | V | Differential, LVCMOS | 8 |
| Output driver supply voltage (NOM 2.5 V) | VDDO_x | 1.7 | 2.5 | 3.465 | V | Differential, LVCMOS | 8 |
| Output driver supply voltage (NOM 3.3 V) | VDDO_x | 1.7 | 3.3 | 3.465 | V | Differential, LVCMOS | 8 |
| Ambient temperature | TA | -40 | 25 | 85 | °C | | 8 |
| Junction temperature | TJ | | | 125 | °C | | 8 |
| Maximum VDD power-up ramp | dVDD/dt | 0.1 | | 100 | ms | | 8 |
| EEPROM number of writes | WR | | | 100 | writes | | 8 |
| Junction-to-ambient thermal resistance | RθJA | | 26.47 | | °C/W | 4-layer JEDEC board, airflow 0 LFM | 8 |
| Junction-to-ambient thermal resistance | RθJA | | 16.4 | | °C/W | Airflow 200 LFM | 8 |
| Junction-to-ambient thermal resistance | RθJA | | 14.62 | | °C/W | Airflow 400 LFM | 8 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 16.57 | | °C/W | Airflow 0 LFM | 8 |
| Junction-to-board thermal resistance | RθJB | | 6.84 | | °C/W | Airflow 0 LFM | 8 |
| Junction-to-board characterization parameter | ψJB | | 4.02 | | °C/W | Airflow 0 LFM | 8 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 1.06 | | °C/W | Airflow 0 LFM | 8 |
| Junction-to-ambient thermal resistance | RθJA | | 10 | | °C/W | 10-layer 200 mm × 250 mm board, 36 thermal vias, Airflow = 0 LFM | 8 |
| Power-down current, total device | IDD-PD | | 30 | 50 | mA | Power down (PDN = 0) | 9 |
| Current consumption, VDD_IN | IDD_IN | | 48 | 65 | mA | Per supply pin; test setup as printed, VDD = 3.3 V, VDDO_xx = 3.3 V, OUT[0-7] = 156.25 MHz LVPECL | 9 |
| Current consumption, VDD_PLL | IDD_PLL | | 128 | 158 | mA | Same test setup as IDD_IN | 9 |
| Current consumption, VDD_LDO | IDD_LDO | | 15 | 30 | mA | Same test setup as IDD_IN | 9 |
| Current consumption, VDD_DIG | IDD_DIG | | 19 | 38 | mA | Same test setup as IDD_IN | 9 |
| Output supply current, VDDO_01 | IDDO_01 | | 85 | 105 | mA | Same test setup as IDD_IN | 9 |
| Output supply current, VDDO_23 | IDDO_23 | | 85 | 105 | mA | Same test setup as IDD_IN | 9 |
| Output supply current, VDDO_4 | IDDO_4 | | 58 | 75 | mA | Same test setup as IDD_IN | 9 |
| Crystal frequency (pullable) | fXTAL | 10 | | 52 | MHz | Fundamental mode | 10 |
| Crystal ESR (pullable) | ESR | | | 60 | Ω | fXTAL = 10 MHz to 16 MHz (50 Ω for 16-30 MHz, 30 Ω for 30-52 MHz) | 10 |
| Crystal maximum drive level | PXTAL | | | 300 | µW | | 10 |
| On-chip XO input capacitance | CXO | 14 | | 24 | pF | Single-ended, each pin referenced to GND | 10 |
| Pulling range | fPR | -50 | | 50 | ppm | Crystal C0/C1 < 250 | 10 |
| Input frequency range | fCLK | 1 | | 300 | MHz | | 11 |
| LVCMOS input high voltage (PRI_REF) | VIH | 1.4 | | | V | PRI_REF; max printed as VDD_IN | 11 |
| LVCMOS input high voltage (SEC_REF) | VIH | 1.4 | | 2.6 | V | SEC_REF | 11 |
| LVCMOS input low voltage | VIL | 0 | | 0.5 | V | | 11 |
| Input voltage swing, differential peak-peak | VID,DIFF,PP | 0.2 | | 2 | V | Differential input | 11 |
| Input leakage current | IIN | -100 | | 100 | µA | | 11 |
| VCO frequency range | fVCO | 4.8 | | 5.4 | GHz | | 11 |
| Phase detector frequency | fPD | 1 | | 150 | MHz | | 12 |
| 1.8-V LVCMOS output frequency | fOUT | 1 | | 200 | MHz | | 12 |
| 1.8-V LVCMOS output high voltage | VOH | 1.35 | | | V | IOH = 1 mA | 12 |
| 1.8-V LVCMOS output low voltage | VOL | | | 0.35 | V | IOL = 1 mA | 12 |
| STATUS LVCMOS output high voltage | VOH | 2.5 | | | V | IOH = 1 mA | 12 |
| STATUS LVCMOS output low voltage | VOL | | | 0.6 | V | IOL = 1 mA | 12 |
| STATUS open-drain output low voltage | VOL | | | 0.6 | V | | 13 |
| AC-LVPECL output frequency | fOUT | 1 | | 1000 | MHz | | 13 |
| AC-LVPECL output voltage swing | VOD | 500 | 800 | 1000 | mV | AC-coupled to 100-Ω differential load | 13 |
| AC-LVDS output voltage swing | VOD | 250 | 400 | 450 | mV | AC-coupled to 100-Ω differential load | 13 |
| AC-CML output voltage swing | VOD | 400 | 600 | 800 | mV | AC-coupled to 100-Ω differential load | 14 |
| HCSL output high voltage | VOH | 660 | | 850 | mV | Outputs with 50 Ω // 2 pF to GND | 14 |
| HCSL absolute crossing voltage | VCROSS | 250 | | 550 | mV | Outputs with 50 Ω // 2 pF to GND | 14 |
| Power-on reset threshold voltage | VTHRESH | 2.72 | | 2.95 | V | | 14 |
| 2-level logic input high voltage | VIH | 1.2 | | | V | HW_SW_CTRL, PDN, GPIO[5:0] | 15 |
| 2-level logic input low voltage | VIL | | | 0.6 | V | HW_SW_CTRL, PDN, GPIO[5:0] | 15 |
| I2C clock rate | fSCL | 100 | | 400 | kHz | | 16 |
| Closed-loop RMS phase jitter, 50-MHz crystal, integer-N | RJ | | 100 | 150 | fs RMS | 50-MHz crystal, Integer-N PLL, fOUT = 156.25 MHz, all differential output types | 17 |
## CAD (KiCad official)
- Symbol: `LMK03318RHSR`
- Footprint: `Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm`
- 3D model: WQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files: `lmk03318rhsr-etched.step` / `lmk03318rhsr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmk03318rhsr.step` / `lmk03318rhsr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lmk03318) (143 pp, sha256 `fa53e5cc6a892d69`, retrieved 2026-10-30, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lmk03318rhsr-datasheet.pdf)