Generated by kicad-footprint-generator · KiCad file format 20260206
LMH6401IRMZR
Texas Instruments · Programmable / Variable Gain Amplifiers (PGA/VGA) · UQFN-16(3x3)
LMH6401IRMZR from Texas Instruments, in a UQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDI | input | Serial interface (SPI) input data pin. Receives register write data clocked in on SCLK when CS is asserted low. |
| 2 | INP | input | Positive differential analog signal input pin. Part of the 100-ohm differential input impedance signal path. |
| 3 | INM | input | Negative differential analog signal input pin. Part of the 100-ohm differential input impedance signal path. |
| 4 | SDO | output | Serial interface (SPI) output data pin. Provides read-back data from the register map. |
| 5 | VS- | power_in | Negative supply voltage. Tied to GND for single-supply 5.0-V operation, or to a negative rail for split-supply operation. Supply range: (VS+) - (VS-) = 4.0 V to 5.25 V. |
| 6 | PD | input | Power-down control pin. Logic 0 = amplifier enabled; logic 1 = amplifier disabled. |
| 7 | VOCM | input | Output common-mode voltage set pin. Drive this pin to set the amplifier's differential output common-mode level, typically to match the input common-mode of the downstream ADC. |
| 8 | VS+ | power_in | Positive supply voltage. Nominal 5.0 V (range 4.0 V to 5.25 V). Bypass to GND close to the pin. |
| 9 | GND | power_in | Ground reference for the device. Connect to the PCB ground plane. |
| 10 | OUTM | output | Negative differential output pin. Drives the negative side of the differential output through an internal 10-ohm series resistor. |
| 11 | OUTP | output | Positive differential output pin. Drives the positive side of the differential output through an internal 10-ohm series resistor. |
| 12 | GND | power_in | Ground reference for the device. Connect to the PCB ground plane. |
| 13 | VS+ | power_in | Positive supply voltage. Nominal 5.0 V (range 4.0 V to 5.25 V). Bypass to GND close to the pin. |
| 14 | SCLK | input | Serial interface (SPI) clock input. Clocks SDI in and SDO out while CS is asserted low. |
| 15 | CS | input | Active-low SPI chip select. Assert low to begin a SPI transaction; de-assert high to complete the transaction and latch data. |
| 16 | VS- | power_in | Negative supply voltage. Tied to GND for single-supply 5.0-V operation, or to a negative rail for split-supply operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | UQFN-16(3x3) |
| Category | Amplifiers/Comparators |
| Pins | 16 |
Ordering variants
Same part, different packaging or reel option.
LMH6401IRMZRLMH6401IRMZT
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | V | 5.5 | V | V = (VS+) – (VS–) | 5 | ||
| Digital input pins | -0.3 | V | 5 | ||||
| Maximum input difference voltage | 2.1 | V | 5 | ||||
| Maximum junction temperature | TJ | 150 | °C | 5 | |||
| Maximum junction temperature, continuous operation | TJ | 125 | °C | Continuous operation, long-term reliability | 5 | ||
| Operating free-air temperature | TA | -40 | 85 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Supply voltage | 4 | 5 | 5.25 | V | 5 | ||
| Minimum operating positive (VS+) supply voltage | 2 | V | 5 | ||||
| Ambient operating air temperature | TA | -40 | 25 | 85 | °C | 5 | |
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Maximum voltage gain | 25.5 | 26 | 26.5 | dB | 6 | ||
| Minimum voltage gain | -7.5 | -6 | -4.5 | dB | 6 | ||
| Gain step size | 0.9 | 1 | 1.1 | dB | 6 | ||
| Cumulative gain error | -0.5 | 0.5 | dB | AV = 26 dB to 10 dB (referenced to 26-dB gain) | 6 | ||
| Cumulative gain error | -1 | 1 | dB | AV = 26 dB to –6 dB (referenced to 26-dB gain) | 6 | ||
| Input resistance | Ri | 85 | 100 | 112 | Ω | Differential | 7 |
| Input common-mode voltage | VICM | -0.3 | 0.3 | V | Self-biased to mid-supply | 7 | |
| Output resistance | Ro | 18 | 20 | 25 | Ω | Differential | 7 |
| Common-mode rejection ratio | CMRR | 38.4 | 45 | dB | ±0.3-V input common-mode shift | 7 | |
| Supply voltage | VS | 4 | 5 | 5.25 | V | 7 | |
| Minimum positive (VS+) supply voltage | 2 | V | 7 | ||||
| Power-supply rejection ratio, VS– | PSRR | 66 | 70 | dB | VS–, measured at 1-kHz sine-wave | 7 | |
| Power-supply rejection ratio, VS+ | PSRR | 66 | 70 | dB | VS+, measured at 1-kHz sine-wave | 7 | |
| Quiescent current | IQ | 60 | 69 | 78 | mA | PD = 0 (device enabled) | 7 |
| Quiescent current | IQ | 1 | 7 | 12 | mA | PD = 1 (device disabled) | 7 |
| VOCM voltage range low | -0.5 | V | VOCM gain < 2% | 7 | |||
| VOCM voltage range high | 0.5 | V | VOCM gain < 2% | 7 | |||
| Output offset voltage | VOO | -40 | 40 | mV | All gain settings | 7 | |
| Common-mode offset voltage | VOCM | -10 | 10 | mV | VOCM pin driven to GND | 7 | |
| Power-down quiescent current | 1 | 7 | 12 | mA | 7 | ||
| PD bias current | 80 | 100 | µA | PD = 2.5 V | 7 | ||
| High-level input voltage | VIH | 1.2 | V | Referred to GND | 7 | ||
| Low-level input voltage | VIL | 0.8 | V | Referred to GND | 7 | ||
| High-level output voltage | VOH | 1.4 | V | 1 kΩ to GND | 7 | ||
| Low-level output voltage | VOL | 0.4 | V | 1 kΩ to GND | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 78 | °C/W | RMZ (UQFN), 16 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 43 | °C/W | RMZ (UQFN), 16 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 24 | °C/W | RMZ (UQFN), 16 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 2.3 | °C/W | RMZ (UQFN), 16 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 24 | °C/W | RMZ (UQFN), 16 pins | 5 |
CAD (KiCad official)
- Symbol:
LMH6401IRMZR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: UQFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
lmh6401irmzr-etched.step/lmh6401irmzr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmh6401irmzr.step/lmh6401irmzr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (47 pp, sha256
b520d7352b5a5bda, retrieved 2026-08-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).