main
Ray
Publish 0.1.0
35a72cd
LMH1228RTVR
Texas Instruments · Pre-ordered Chips · WQFN-32-EP(5x5)
LMH1228RTVR from Texas Instruments, in a WQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDI_OUT1+ | bidirectional | Single-ended complementary 75-Ω line-side cable driver output with on-chip 75-Ω termination, AC-coupled through 4.7 µF to a BNC, with nominal 800 mVp-p output amplitude. |
| 2 | SDI_OUT1- | bidirectional | Complementary line-side cable driver output of SDI_OUT1±, AC-coupled through 4.7 µF and terminated with an external 75-Ω resistor to GND. |
| 3 | VSS | power_in | Ground reference for the device. |
| 4 | OUT0_SEL | input | LVCMOS control that enables the 100-Ω host-side loop-back driver at OUT0± when set low; internally pulled high by default (OUT0 disabled). |
| 5 | RSV6 | input | Reserved LVCMOS input that must be tied high to VIN through a 1-kΩ resistor, or overridden by register control; internally pulled low by default. |
| 6 | VSS | power_in | Ground reference for the device. |
| 7 | SDI_OUT2- | output | Complementary secondary line-side 75-Ω cable driver output, AC-coupled through 4.7 µF and terminated with an external 75-Ω resistor to GND. |
| 8 | SDI_OUT2+ | output | Secondary line-side 75-Ω cable driver output with on-chip 75-Ω termination, AC-coupled through 4.7 µF to a BNC; enabled by SDI_OUT2_SEL. |
| 9 | HOST_EQ0 | input | 4-level input that selects the IN0± equalizer mode and boost setting, with F (float) recommended for normal operation; it also sets the OUT0 VOD and de-emphasis. |
| 10 | RSV1 | unconnected | Reserved pin; do not connect. |
| 11 | SS_N / ADDR0 | input | In SPI mode (MODE_SEL = F) this is the active-low slave select, internally pulled high; in SMBus mode (MODE_SEL = L) it is the 4-level address strap ADDR0 read at power-up. |
| 12 | MODE_SEL | input | 4-level input that selects the serial interface: F selects SPI, L selects SMBus, and H or R are reserved for factory testing and must not be used. |
| 13 | MOSI / SDA | input | In SPI mode this is the SPI data input (2.5-V LVCMOS, external pullup recommended); in SMBus mode it is the open-drain bidirectional SDA line, 3.3-V tolerant, requiring an external pullup. |
| 14 | SDI_OUT2_SEL | input | LVCMOS control that enables the 75-Ω output driver at SDI_OUT2± when set low; internally pulled high by default (SDI_OUT2 disabled). |
| 15 | RSV2 | unconnected | Reserved pin; do not connect. |
| 16 | RSV3 | unconnected | Reserved pin; do not connect. |
| 17 | OUT_CTRL | input | 4-level input that selects the routed signal path, enabling the reclocker in normal operation (F) or bypassing it (R or L); it may be overridden by register control. |
| 18 | IN0- | input | Complementary differential input from the host video processor with on-chip 100-Ω differential termination, requiring an external 4.7-µF AC-coupling capacitor for SMPTE applications. |
| 19 | IN0+ | input | Differential input from the host video processor with on-chip 100-Ω differential termination, requiring an external 4.7-µF AC-coupling capacitor for SMPTE applications. |
| 20 | VSS | power_in | Ground reference for the device. |
| 21 | VDD_CDR | power_in | Supplies the reclocker circuitry; connected to the same 2.5 V ±5% supply as VIN (2.375 V to 2.625 V). |
| 22 | OUT0- | output | Complementary differential 100-Ω host-side output to the downstream video processor, with on-chip 100-Ω termination and AC coupling via 4.7 µF. |
| 23 | OUT0+ | output | Differential 100-Ω host-side output to the downstream video processor, with on-chip 100-Ω termination and AC coupling via 4.7 µF. |
| 24 | SDI_VOD | input | 4-level input that selects one of four line-side cable driver output amplitudes (H about +5%, F 800 mVp-p nominal, R about +10%, L about -5%). |
| 25 | RSV4 | unconnected | Reserved pin; do not connect. |
| 26 | RSV5 | unconnected | Reserved pin; do not connect. |
| 27 | LOCK_N | output | 3.3-V tolerant open-drain reclocker lock indicator, pulled low when CDR lock is acquired; requires an external pullup to a logic supply and can be reconfigured to SD_N or INT_N. |
| 28 | MISO / ADDR1 | output | In SPI mode this is the 2.5-V LVCMOS SPI data output, which floats when SS_N is high; in SMBus mode it is the 4-level address strap ADDR1 read at power-up. |
| 29 | SCK / SCL | input | In SPI mode this is the SPI serial clock input (2.5-V LVCMOS, external pullup recommended); in SMBus mode it is the open-drain SCL clock, 3.3-V tolerant, requiring an external pullup. |
| 30 | VIN | power_in | Connected to an external 2.5-V ±5% supply (2.375 V to 2.625 V) for the device; absolute maximum supply is 2.75 V. |
| 31 | VDD_LDO | power_out | Output of the internal 1.8-V LDO that powers internal circuitry only and requires external 1-µF and 0.1-µF bypass capacitors to VSS. |
| 32 | ENABLE | input | LVCMOS power-down control: logic high enables normal operation and logic low places the device in Power-Down Mode; internally pulled high by default. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-32-EP(5x5) |
| Category | Interface ICs |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (VIN, VDD_CDR) | -0.5 | 2.75 | V | 5 | |||
| Input voltage for 4-level pins | -0.5 | 2.75 | V | 5 | |||
| Input/output voltage for 2-level control pins | -0.5 | 2.75 | V | 5 | |||
| SMBus input/output voltage (SDA, SCL) | -0.5 | 4 | V | 5 | |||
| SPI input/output voltage (SS_N, MISO, MOSI, SCK) | -0.5 | 2.75 | V | 5 | |||
| High-speed input/output voltage (IN0±, SDI_OUT1±, OUT0±, SDI_OUT2±) | -0.5 | 2.75 | V | 5 | |||
| Input current (IN0±) | -30 | 30 | mA | 5 | |||
| Operating junction temperature | 125 | °C | 5 | ||||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| ESD HBM, all pins except 13 and 29 | V(ESD) | -6000 | 6000 | V | ANSI/ESDA/JEDEC JS-001 | 5 | |
| ESD HBM, pins 13 and 29 | V(ESD) | -5500 | 5500 | V | ANSI/ESDA/JEDEC JS-001 | 5 | |
| ESD CDM | V(ESD) | -1500 | 1500 | V | JESD22-C101 | 5 | |
| Supply voltage VIN, VDD_CDR to VSS | 2.375 | 2.5 | 2.625 | V | 5 | ||
| SMBus SDA, SCL open-drain termination voltage | VDDSMBUS | 2.375 | 3.6 | V | 5 | ||
| Source differential launch amplitude, 5-inch trace | VIN0_LAUNCH | 300 | 850 | mVp-p | Before 5-inch board trace to IN0± | 5 | |
| Source differential launch amplitude, 20-inch trace | VIN0_LAUNCH | 650 | 1000 | mVp-p | Before 20-inch board trace to IN0± | 5 | |
| Operating junction temperature | TJUNCTION | 110 | °C | 5 | |||
| Ambient temperature | TAMBIENT | -40 | 25 | 85 | °C | 5 | |
| Maximum supply noise, 50 Hz to 1 MHz | NTpsmax | 20 | mVp-p | 50 Hz to 1 MHz, sinusoidal | 5 | ||
| Maximum supply noise, 1.1 MHz to 50 MHz | NTpsmax | 10 | mVp-p | 1.1 MHz to 50 MHz, sinusoidal | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 32.5 | °C/W | RTV (WQFN) 32 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 15 | °C/W | RTV (WQFN) 32 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 6.5 | °C/W | RTV (WQFN) 32 pins | 6 | ||
| Junction-to-top characterization parameter | ψJT | 0.2 | °C/W | RTV (WQFN) 32 pins | 6 | ||
| Junction-to-board characterization parameter | ψJB | 6.5 | °C/W | RTV (WQFN) 32 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.7 | °C/W | RTV (WQFN) 32 pins | 6 | ||
| Current consumption, SDI_OUT1 only | IDD | 122 | 146 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± disabled | 6 | |
| Current consumption, SDI_OUT1 and OUT0 | IDD | 140 | 166 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± enabled | 6 | |
| Current consumption, SDI_OUT1 and SDI_OUT2 | IDD | 177 | 211 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± disabled | 6 | |
| Current consumption, all outputs | IDD | 194 | 230 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± enabled | 6 | |
| Current consumption, Power-Down Mode | IDDZ_PD | 10 | 30 | mA | Power-Down Mode, ENABLE = L, no signal applied at IN0± | 6 | |
| Current consumption, Power Save Mode | IDDZ | 10 | mA | Power Save Mode, ENABLE = H, no signal applied at IN0± | 6 | ||
| Power dissipation, SDI_OUT1 only | PD | 305 | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± disabled | 6 | ||
| Power dissipation, SDI_OUT1 and OUT0 | PD | 350 | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± enabled | 6 | ||
| Power dissipation, SDI_OUT1 and SDI_OUT2 | PD | 442 | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± disabled | 6 | ||
| Power dissipation, all outputs | PD | 485 | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± enabled | 6 | ||
| Power dissipation, Power Save Mode | PDZ | 25 | mW | Power Save Mode, ENABLE = H, no signal applied at IN0± | 6 | ||
| Logic high input voltage (SCL, SDA) | VIH | 3.6 | V | 2-level input (SCL, SDA) | 7 | ||
| Logic low input voltage (2-level inputs) | VIL | 0 | V | 2-level input (SS_N, SCK, MOSI, SDI_OUT2_SEL, OUT0_SEL, ENABLE, SCL, SDA) | 7 | ||
| Logic low output voltage (MISO) | VOL | 0 | V | IOL = 2 mA, (MISO) | 7 | ||
| Logic low output voltage (LOCK_N, SDA) | VOL | 0.4 | V | IOL = 3 mA, (LOCK_N, SDA) | 7 | ||
| 4-level LEVEL-L input voltage | VLVL_L | 0 | V | Measured voltage at 4-level pin with external 1 kΩ to VSS | 8 | ||
| Input high leakage current, 4-level pins | IIH | 20 | 45 | 80 | µA | Vinput = VIN; HOST_EQ0, MODE_SEL, OUT_CTRL, SDI_VOD | 8 |
| Input low leakage current, 4-level pins | IIL | -160 | -93 | -40 | µA | Vinput = GND; HOST_EQ0, MODE_SEL, OUT_CTRL, SDI_VOD | 8 |
| DC input differential termination | RIN0_TERM | 80 | 100 | 120 | Ω | Measured across IN0+ to IN0- | 8 |
| DC output single-ended termination | ROUT_TERM | 63 | 75 | 87 | Ω | SDI_OUT1+ and SDI_OUT1-, SDI_OUT2+ and SDI_OUT2- to VIN | 8 |
| Output single-ended output voltage at SDI_OUT+, SDI_VOD = F | VODCD_OUTP | 720 | 800 | 880 | mVp-p | SDI_VOD = F; other output AC terminated with 75 Ω | 8 |
| Output single-ended output voltage at SDI_OUT-, SDI_VOD = F | VODCD_OUTN | 720 | 800 | 880 | mVp-p | SDI_VOD = F; other output AC terminated with 75 Ω | 8 |
| Output rise and fall time, 11.88 Gbps | tR_F_SDI | 34 | 42 | ps | PRBS10, default VOD, 20%-80%, default pre-emphasis enabled, 11.88 Gbps | 9 | |
| DC output differential termination | ROUT0_TERM | 80 | 100 | 120 | Ω | Measured across OUT0+ and OUT0- | 10 |
| Output differential voltage at OUT0±, HOST_EQ0 = F | VODOUT0 | 485 | 560 | 620 | mVp-p | Measured with 8T pattern, HOST_EQ0 = F | 10 |
| SMBus SCL frequency | FSCL | 10 | 400 | kHz | 11 | ||
| Bus free time between stop and start condition | TBUF | 1.3 | µs | See Figure 1. | 11 | ||
| SPI SCK frequency | FSCK | 20 | MHz | 12 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
LMH1228RTVR - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: WQFN-32-EP(5x5), generated on the KiCad land (body 5 x 5 mm, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lmh1228rtvr-etched.step/lmh1228rtvr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmh1228rtvr.step/lmh1228rtvr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (45 pp, sha256
5fc09840bc5866cd, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# LMH1228RTVR
**Texas Instruments** · Pre-ordered Chips · WQFN-32-EP(5x5)
LMH1228RTVR from Texas Instruments, in a WQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDI_OUT1+ | bidirectional | Single-ended complementary 75-Ω line-side cable driver output with on-chip 75-Ω termination, AC-coupled through 4.7 µF to a BNC, with nominal 800 mVp-p output amplitude. |
| 2 | SDI_OUT1- | bidirectional | Complementary line-side cable driver output of SDI_OUT1±, AC-coupled through 4.7 µF and terminated with an external 75-Ω resistor to GND. |
| 3 | VSS | power_in | Ground reference for the device. |
| 4 | OUT0_SEL | input | LVCMOS control that enables the 100-Ω host-side loop-back driver at OUT0± when set low; internally pulled high by default (OUT0 disabled). |
| 5 | RSV6 | input | Reserved LVCMOS input that must be tied high to VIN through a 1-kΩ resistor, or overridden by register control; internally pulled low by default. |
| 6 | VSS | power_in | Ground reference for the device. |
| 7 | SDI_OUT2- | output | Complementary secondary line-side 75-Ω cable driver output, AC-coupled through 4.7 µF and terminated with an external 75-Ω resistor to GND. |
| 8 | SDI_OUT2+ | output | Secondary line-side 75-Ω cable driver output with on-chip 75-Ω termination, AC-coupled through 4.7 µF to a BNC; enabled by SDI_OUT2_SEL. |
| 9 | HOST_EQ0 | input | 4-level input that selects the IN0± equalizer mode and boost setting, with F (float) recommended for normal operation; it also sets the OUT0 VOD and de-emphasis. |
| 10 | RSV1 | unconnected | Reserved pin; do not connect. |
| 11 | SS_N / ADDR0 | input | In SPI mode (MODE_SEL = F) this is the active-low slave select, internally pulled high; in SMBus mode (MODE_SEL = L) it is the 4-level address strap ADDR0 read at power-up. |
| 12 | MODE_SEL | input | 4-level input that selects the serial interface: F selects SPI, L selects SMBus, and H or R are reserved for factory testing and must not be used. |
| 13 | MOSI / SDA | input | In SPI mode this is the SPI data input (2.5-V LVCMOS, external pullup recommended); in SMBus mode it is the open-drain bidirectional SDA line, 3.3-V tolerant, requiring an external pullup. |
| 14 | SDI_OUT2_SEL | input | LVCMOS control that enables the 75-Ω output driver at SDI_OUT2± when set low; internally pulled high by default (SDI_OUT2 disabled). |
| 15 | RSV2 | unconnected | Reserved pin; do not connect. |
| 16 | RSV3 | unconnected | Reserved pin; do not connect. |
| 17 | OUT_CTRL | input | 4-level input that selects the routed signal path, enabling the reclocker in normal operation (F) or bypassing it (R or L); it may be overridden by register control. |
| 18 | IN0- | input | Complementary differential input from the host video processor with on-chip 100-Ω differential termination, requiring an external 4.7-µF AC-coupling capacitor for SMPTE applications. |
| 19 | IN0+ | input | Differential input from the host video processor with on-chip 100-Ω differential termination, requiring an external 4.7-µF AC-coupling capacitor for SMPTE applications. |
| 20 | VSS | power_in | Ground reference for the device. |
| 21 | VDD_CDR | power_in | Supplies the reclocker circuitry; connected to the same 2.5 V ±5% supply as VIN (2.375 V to 2.625 V). |
| 22 | OUT0- | output | Complementary differential 100-Ω host-side output to the downstream video processor, with on-chip 100-Ω termination and AC coupling via 4.7 µF. |
| 23 | OUT0+ | output | Differential 100-Ω host-side output to the downstream video processor, with on-chip 100-Ω termination and AC coupling via 4.7 µF. |
| 24 | SDI_VOD | input | 4-level input that selects one of four line-side cable driver output amplitudes (H about +5%, F 800 mVp-p nominal, R about +10%, L about -5%). |
| 25 | RSV4 | unconnected | Reserved pin; do not connect. |
| 26 | RSV5 | unconnected | Reserved pin; do not connect. |
| 27 | LOCK_N | output | 3.3-V tolerant open-drain reclocker lock indicator, pulled low when CDR lock is acquired; requires an external pullup to a logic supply and can be reconfigured to SD_N or INT_N. |
| 28 | MISO / ADDR1 | output | In SPI mode this is the 2.5-V LVCMOS SPI data output, which floats when SS_N is high; in SMBus mode it is the 4-level address strap ADDR1 read at power-up. |
| 29 | SCK / SCL | input | In SPI mode this is the SPI serial clock input (2.5-V LVCMOS, external pullup recommended); in SMBus mode it is the open-drain SCL clock, 3.3-V tolerant, requiring an external pullup. |
| 30 | VIN | power_in | Connected to an external 2.5-V ±5% supply (2.375 V to 2.625 V) for the device; absolute maximum supply is 2.75 V. |
| 31 | VDD_LDO | power_out | Output of the internal 1.8-V LDO that powers internal circuitry only and requires external 1-µF and 0.1-µF bypass capacitors to VSS. |
| 32 | ENABLE | input | LVCMOS power-down control: logic high enables normal operation and logic low places the device in Power-Down Mode; internally pulled high by default. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-32-EP(5x5) |
| Category | Interface ICs |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (VIN, VDD_CDR) | | -0.5 | | 2.75 | V | | 5 |
| Input voltage for 4-level pins | | -0.5 | | 2.75 | V | | 5 |
| Input/output voltage for 2-level control pins | | -0.5 | | 2.75 | V | | 5 |
| SMBus input/output voltage (SDA, SCL) | | -0.5 | | 4 | V | | 5 |
| SPI input/output voltage (SS_N, MISO, MOSI, SCK) | | -0.5 | | 2.75 | V | | 5 |
| High-speed input/output voltage (IN0±, SDI_OUT1±, OUT0±, SDI_OUT2±) | | -0.5 | | 2.75 | V | | 5 |
| Input current (IN0±) | | -30 | | 30 | mA | | 5 |
| Operating junction temperature | | | | 125 | °C | | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| ESD HBM, all pins except 13 and 29 | V(ESD) | -6000 | | 6000 | V | ANSI/ESDA/JEDEC JS-001 | 5 |
| ESD HBM, pins 13 and 29 | V(ESD) | -5500 | | 5500 | V | ANSI/ESDA/JEDEC JS-001 | 5 |
| ESD CDM | V(ESD) | -1500 | | 1500 | V | JESD22-C101 | 5 |
| Supply voltage VIN, VDD_CDR to VSS | | 2.375 | 2.5 | 2.625 | V | | 5 |
| SMBus SDA, SCL open-drain termination voltage | VDDSMBUS | 2.375 | | 3.6 | V | | 5 |
| Source differential launch amplitude, 5-inch trace | VIN0_LAUNCH | 300 | | 850 | mVp-p | Before 5-inch board trace to IN0± | 5 |
| Source differential launch amplitude, 20-inch trace | VIN0_LAUNCH | 650 | | 1000 | mVp-p | Before 20-inch board trace to IN0± | 5 |
| Operating junction temperature | TJUNCTION | | | 110 | °C | | 5 |
| Ambient temperature | TAMBIENT | -40 | 25 | 85 | °C | | 5 |
| Maximum supply noise, 50 Hz to 1 MHz | NTpsmax | | | 20 | mVp-p | 50 Hz to 1 MHz, sinusoidal | 5 |
| Maximum supply noise, 1.1 MHz to 50 MHz | NTpsmax | | | 10 | mVp-p | 1.1 MHz to 50 MHz, sinusoidal | 5 |
| Junction-to-ambient thermal resistance | RθJA | | 32.5 | | °C/W | RTV (WQFN) 32 pins | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 15 | | °C/W | RTV (WQFN) 32 pins | 6 |
| Junction-to-board thermal resistance | RθJB | | 6.5 | | °C/W | RTV (WQFN) 32 pins | 6 |
| Junction-to-top characterization parameter | ψJT | | 0.2 | | °C/W | RTV (WQFN) 32 pins | 6 |
| Junction-to-board characterization parameter | ψJB | | 6.5 | | °C/W | RTV (WQFN) 32 pins | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 1.7 | | °C/W | RTV (WQFN) 32 pins | 6 |
| Current consumption, SDI_OUT1 only | IDD | | 122 | 146 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± disabled | 6 |
| Current consumption, SDI_OUT1 and OUT0 | IDD | | 140 | 166 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± enabled | 6 |
| Current consumption, SDI_OUT1 and SDI_OUT2 | IDD | | 177 | 211 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± disabled | 6 |
| Current consumption, all outputs | IDD | | 194 | 230 | mA | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± enabled | 6 |
| Current consumption, Power-Down Mode | IDDZ_PD | | 10 | 30 | mA | Power-Down Mode, ENABLE = L, no signal applied at IN0± | 6 |
| Current consumption, Power Save Mode | IDDZ | | 10 | | mA | Power Save Mode, ENABLE = H, no signal applied at IN0± | 6 |
| Power dissipation, SDI_OUT1 only | PD | | 305 | | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± disabled | 6 |
| Power dissipation, SDI_OUT1 and OUT0 | PD | | 350 | | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± disabled, OUT0± enabled | 6 |
| Power dissipation, SDI_OUT1 and SDI_OUT2 | PD | | 442 | | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± disabled | 6 |
| Power dissipation, all outputs | PD | | 485 | | mW | PRBS10, CDR locked 11.88 Gbps; SDI_OUT1± enabled, SDI_OUT2± enabled, OUT0± enabled | 6 |
| Power dissipation, Power Save Mode | PDZ | | 25 | | mW | Power Save Mode, ENABLE = H, no signal applied at IN0± | 6 |
| Logic high input voltage (SCL, SDA) | VIH | | | 3.6 | V | 2-level input (SCL, SDA) | 7 |
| Logic low input voltage (2-level inputs) | VIL | 0 | | | V | 2-level input (SS_N, SCK, MOSI, SDI_OUT2_SEL, OUT0_SEL, ENABLE, SCL, SDA) | 7 |
| Logic low output voltage (MISO) | VOL | 0 | | | V | IOL = 2 mA, (MISO) | 7 |
| Logic low output voltage (LOCK_N, SDA) | VOL | | | 0.4 | V | IOL = 3 mA, (LOCK_N, SDA) | 7 |
| 4-level LEVEL-L input voltage | VLVL_L | | 0 | | V | Measured voltage at 4-level pin with external 1 kΩ to VSS | 8 |
| Input high leakage current, 4-level pins | IIH | 20 | 45 | 80 | µA | Vinput = VIN; HOST_EQ0, MODE_SEL, OUT_CTRL, SDI_VOD | 8 |
| Input low leakage current, 4-level pins | IIL | -160 | -93 | -40 | µA | Vinput = GND; HOST_EQ0, MODE_SEL, OUT_CTRL, SDI_VOD | 8 |
| DC input differential termination | RIN0_TERM | 80 | 100 | 120 | Ω | Measured across IN0+ to IN0- | 8 |
| DC output single-ended termination | ROUT_TERM | 63 | 75 | 87 | Ω | SDI_OUT1+ and SDI_OUT1-, SDI_OUT2+ and SDI_OUT2- to VIN | 8 |
| Output single-ended output voltage at SDI_OUT+, SDI_VOD = F | VODCD_OUTP | 720 | 800 | 880 | mVp-p | SDI_VOD = F; other output AC terminated with 75 Ω | 8 |
| Output single-ended output voltage at SDI_OUT-, SDI_VOD = F | VODCD_OUTN | 720 | 800 | 880 | mVp-p | SDI_VOD = F; other output AC terminated with 75 Ω | 8 |
| Output rise and fall time, 11.88 Gbps | tR_F_SDI | | 34 | 42 | ps | PRBS10, default VOD, 20%-80%, default pre-emphasis enabled, 11.88 Gbps | 9 |
| DC output differential termination | ROUT0_TERM | 80 | 100 | 120 | Ω | Measured across OUT0+ and OUT0- | 10 |
| Output differential voltage at OUT0±, HOST_EQ0 = F | VODOUT0 | 485 | 560 | 620 | mVp-p | Measured with 8T pattern, HOST_EQ0 = F | 10 |
| SMBus SCL frequency | FSCL | 10 | | 400 | kHz | | 11 |
| Bus free time between stop and start condition | TBUF | 1.3 | | | µs | See Figure 1. | 11 |
| SPI SCK frequency | FSCK | | | 20 | MHz | | 12 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `LMH1228RTVR`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`
- 3D model: WQFN-32-EP(5x5), generated on the KiCad land (body 5 x 5 mm, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `lmh1228rtvr-etched.step` / `lmh1228rtvr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmh1228rtvr.step` / `lmh1228rtvr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lmh1228.pdf) (45 pp, sha256 `5fc09840bc5866cd`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/lmh1228rtvr-datasheet.pdf)