3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLMH0318RTWR
Texas Instruments · Clock And Data Recovery / Retiming · WQFN-24-EP(4x4)
LMH0318RTWR from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE_SEL | input | Four-level strap that selects the control interface: 1 kΩ to VDD selects SPI mode, and 1 kΩ to GND selects SMBus mode (20 kΩ to GND and float are reserved). |
| 2 | IN_OUT_SEL_SPI_SS_N_ADR0 | input | In SPI mode this is the SPI slave select input (SPI_SS_N, with internal pull-up); in SMBus mode it is a four-level strap (ADDR0) that sets the SMBus address, read at power-up. |
| 3 | EQ_SCL_SCK | input | In SPI mode this is the SPI serial clock input (2.5 V LVCMOS, 10 to 20 MHz SPI clock frequency); in SMBus mode it is the SMBus clock input, which is open drain, needs an external 2 kΩ to 5 kΩ pull-up, and is 3.3 V LVCMOS tolerant. |
| 4 | OUT_CTRL_MOSI_SDA | bidirectional | In SPI mode this is the SPI master-output/slave-input data pin (MOSI, 2.5 V LVCMOS); in SMBus mode it is the open-drain SMBus data pin, which needs an external 2 kΩ to 5 kΩ pull-up and is 3.3 V LVCMOS tolerant. |
| 5 | RESERVED | unconnected | Reserved pin; no connect. |
| 6 | ENABLE | input | Four-level pin: 1 kΩ to VDD gives normal operation, 1 kΩ to GND powers down the device including signal detects and resets registers at power-up, and the float and 20 kΩ to GND states are reserved. |
| 7 | VDD | power_in | 2.5 V supply, 2.5 V ±5% (2.375 V to 2.625 V). |
| 8 | IN1+ | input | Non-inverting high-speed differential input for channel IN1, with an on-chip 100 Ω termination between IN1+ and IN1- and a required 4.7 µF AC coupling capacitor. |
| 9 | IN1- | input | Inverting high-speed differential input for channel IN1, with an on-chip 100 Ω termination between IN1+ and IN1- and a required 4.7 µF AC coupling capacitor. |
| 10 | VSS | power_in | Ground; connect directly to ground (GND). |
| 11 | IN0+ | input | Non-inverting high-speed differential input for channel IN0, with an on-chip 100 Ω termination between IN0+ and IN0- and a required 4.7 µF AC coupling capacitor. |
| 12 | IN0- | input | Inverting high-speed differential input for channel IN0, with an on-chip 100 Ω termination between IN0+ and IN0- and a required 4.7 µF AC coupling capacitor. |
| 13 | LOS_INT_N | output | Open-drain interrupt output that pulls low on loss of signal, eye-monitor threshold violation, or CDR lock change; it needs an external 4.7 kΩ pull-up and is 3.3 V LVCMOS tolerant. |
| 14 | RESERVED | unconnected | Reserved pin; no connect. |
| 15 | VOD_MISO_ADR1 | output | In SPI mode this is the SPI master-input/slave-output data pin (MISO, 2.5 V LVCMOS); in SMBus mode it is a four-level strap (ADDR1) that sets the SMBus address, read at power-up. |
| 16 | LOCK | output | 2.5 V LVCMOS output that is high when the CDR is locked and low when it is not locked. |
| 17 | RESERVED | unconnected | Reserved pin; no connect. |
| 18 | RESERVED | unconnected | Reserved pin; no connect. |
| 19 | OUT0- | output | Inverting 75 Ω CML output for channel OUT0, with an on-chip 75 Ω termination to VDD and a required 4.7 µF AC coupling capacitor. |
| 20 | OUT0+ | output | Non-inverting 75 Ω CML output for channel OUT0, with an on-chip 75 Ω termination to VDD and a required 4.7 µF AC coupling capacitor. |
| 21 | VDD | power_in | 2.5 V supply, 2.5 V ±5% (2.375 V to 2.625 V). |
| 22 | OUT1- | output | Inverting high-speed differential output for channel OUT1, with an on-chip 100 Ω termination between OUT1+ and OUT1- and a required 4.7 µF AC coupling capacitor. |
| 23 | OUT1+ | output | Non-inverting high-speed differential output for channel OUT1, with an on-chip 100 Ω termination between OUT1+ and OUT1- and a required 4.7 µF AC coupling capacitor. |
| 24 | VSS | power_in | Ground; connect directly to ground (GND). |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | RTC/Clock Chip |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
LMH0318RTWR - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lmh0318rtwr-etched.step/lmh0318rtwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmh0318rtwr.step/lmh0318rtwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (57 pp, sha256
fca0f5c3e991f0d7, retrieved 2026-10-10, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).