Generated by kicad-footprint-generator · KiCad file format 20260206
LM76003RNPT
Texas Instruments · Integrated Circuits (ICs) · 30-WFQFN Exposed Pad
LM76003RNPT from Texas Instruments, in a 30-WFQFN Exposed Pad. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor. |
| 2 | SW | power_out | Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor. |
| 3 | SW | power_out | Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor. |
| 4 | SW | power_out | Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor. |
| 5 | SW | power_out | Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor. |
| 6 | BOOT | passive | Bootstrap capacitor connection for the high-side driver; connect a high-quality 470-nF capacitor from this pin to the SW pin. |
| 7 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 8 | VCC | power_out | Output of the internal bias supply used for control circuits; connect a high-quality 2.2-µF capacitor to GND and TI does not recommend loading this pin with external circuitry. |
| 9 | BIAS | power_in | Optional BIAS LDO supply input; TI recommends tying to VOUT when 3.3 V ≤ VOUT ≤ 18 V or to an external 3.3-V or 5-V rail, with a 1-µF capacitor to ground when used, and tying to ground when not in use. |
| 10 | RT | input | Switching frequency setting pin; a resistor from this pin to ground sets the frequency, the default is 500 kHz if floating, and it must not be shorted to ground. |
| 11 | SS/TRK | input | Soft-start control pin; leave floating for the 6.3-ms internal ramp, add an external capacitor to ground to extend soft-start, or connect an external ramp for tracking, and do not short to ground. |
| 12 | FB | input | Feedback input for output voltage regulation via a resistor divider; never short this terminal to ground during operation. |
| 13 | AGND | power_in | Analog ground providing the reference for internal references and logic; all electrical parameters are measured with respect to this pin. |
| 14 | AGND | power_in | Analog ground providing the reference for internal references and logic; all electrical parameters are measured with respect to this pin. |
| 15 | AGND | power_in | Analog ground providing the reference for internal references and logic; all electrical parameters are measured with respect to this pin. |
| 16 | PGOOD | output | Open-drain power-good flag output that connects through a current-limiting resistor to a supply; high means VOUT regulation is OK, low means a fault, and it is low when EN is low. |
| 17 | SYNC/MODE | input | Synchronization and mode setting pin that must not float; tie to ground for DCM/PFM, to logic high for forced PWM, or to an external clock to synchronize switching with forced PWM at light load. |
| 18 | EN | input | Precision-enable input that must not float; high turns the regulator on and low turns it off, and it can be tied to VIN. |
| 19 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 20 | PVIN | power_in | Supply input to the internal bias LDO and HS FET; CIN must be placed right next to this pin and PGND with short traces. |
| 21 | PVIN | power_in | Supply input to the internal bias LDO and HS FET; CIN must be placed right next to this pin and PGND with short traces. |
| 22 | PVIN | power_in | Supply input to the internal bias LDO and HS FET; CIN must be placed right next to this pin and PGND with short traces. |
| 23 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 24 | PGND | power_in | Power ground connected to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT, keeping the path to CIN as short as possible. |
| 25 | PGND | power_in | Power ground connected to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT, keeping the path to CIN as short as possible. |
| 26 | PGND | power_in | Power ground connected to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT, keeping the path to CIN as short as possible. |
| 27 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 28 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 29 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 30 | NC | unconnected | Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability. |
| 31 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | 30-WFQFN Exposed Pad |
| Category | Integrated Circuits (ICs) |
| Pins | 31 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| PVIN to PGND | -0.3 | 65 | V | over operating free-air temperature range | 5 | ||
| EN to AGND (max printed as VIN + 0.3) | -0.3 | V | over operating free-air temperature range | 5 | |||
| FB, RT, SS/TRK to AGND | -0.3 | 5 | V | over operating free-air temperature range | 5 | ||
| PGOOD to AGND | -0.1 | 20 | V | over operating free-air temperature range | 5 | ||
| SYNC to AGND | -0.3 | 5.5 | V | over operating free-air temperature range | 5 | ||
| BIAS to AGND (max printed as lower of VIN + 0.3 or 30) | -0.3 | V | over operating free-air temperature range | 5 | |||
| AGND to PGND | -0.3 | 0.3 | V | over operating free-air temperature range | 5 | ||
| SW to PGND (max printed as VIN + 0.3) | -0.3 | V | over operating free-air temperature range | 5 | |||
| SW to PGND less than 10-ns transients | -3.5 | 65 | V | over operating free-air temperature range | 5 | ||
| BOOT to SW | -0.3 | 5.5 | V | over operating free-air temperature range | 5 | ||
| VCC to AGND | -0.3 | 5.5 | V | over operating free-air temperature range | 5 | ||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| PVIN to PGND (operating) | 3.5 | 60 | V | over operating free-air temperature range | 5 | ||
| EN (max printed as VIN) | 0 | V | over operating free-air temperature range | 5 | |||
| FB | 0 | 4.5 | V | over operating free-air temperature range | 5 | ||
| PGOOD | 0 | 18 | V | over operating free-air temperature range | 5 | ||
| BIAS input not used | 0 | 0.3 | V | over operating free-air temperature range | 5 | ||
| BIAS input used (max printed as lower of VIN + 0.3 or 24) | 0 | V | over operating free-air temperature range | 5 | |||
| AGND to PGND (recommended) | -0.1 | 0.1 | V | over operating free-air temperature range | 5 | ||
| Output voltage (max printed as 95% of VIN) | VOUT | 1 | V | over operating free-air temperature range | 5 | ||
| Output current, LM76003 | IOUT | 0 | 3.5 | A | over operating free-air temperature range | 5 | |
| Operating input voltage range | VIN | 3.5 | 60 | V | 6 | ||
| Shutdown quiescent current; measured at PVIN pin | ISD | 1.2 | 10 | µA | VEN = 0 V, TJ = 25℃ | 6 | |
| Operating quiescent current from VIN (non-switching) | IQ_NONSW | 0.9 | 12 | µA | VEN = 2 V, VFB = 1.5 V, VBIAS = 3.3 V external | 6 | |
| Enable input high level for VOUT | VEN_VOUT_H | 1.14 | 1.204 | 1.25 | V | VEN rising | 6 |
| Enable input leakage current | ILKG_EN | 1.4 | 200 | nA | VEN = 2 V | 6 | |
| Internal VCC undervoltage lockout | VCC_UVLO | 2.96 | 3.14 | 3.27 | V | VCC rising | 6 |
| Operating quiescent current from external VBIAS (non-switching) | IBIAS_NONSW | 21 | 50 | µA | VEN = 2 V, VFB = 1.5 V, VBIAS = 3.3 V external | 6 | |
| Feedback voltage | VFB | 0.987 | 1.006 | 1.017 | V | PWM mode | 6 |
| Input leakage current at FB pin | ILKG_FB | 0.2 | 60 | nA | VFB = 1 V | 6 | |
| BOOT - SW undervoltage lockout | VBOOT_UVLO | 1.6 | 2.2 | 2.7 | V | 7 | |
| Short-circuit, high-side current limit, LM76003 | IHS_LIMIT | 4.35 | 5.5 | 6.8 | A | 7 | |
| Low-side current limit, LM76003 | ILS_LIMIT | 3.4 | 4.2 | 5.3 | A | 7 | |
| Hiccup threshold on FB pin | VHICCUP | 0.38 | 0.42 | 0.46 | V | 7 | |
| Soft-start charge current | ISSC | 1.8 | 2 | 2.2 | µA | 7 | |
| Power-good overvoltage threshold | VPGOOD_OV | 106 | 110 | 113 | % | % of FB voltage | 7 |
| Power-good undervoltage threshold | VPGOOD_UV | 86 | 90 | 93 | % | % of FB voltage | 7 |
| Minimum input voltage for proper PGOOD function | VPGOOD_VALID | 1.3 | 2 | V | 50-µA pullup to PGOOD pin, VEN = 0 V, TJ = 25°C | 7 | |
| Power-good on-resistance | RPGOOD | 40 | 100 | Ω | VEN = 2.5 V | 7 | |
| Power-good on-resistance | RPGOOD | 30 | 90 | Ω | VEN = 0 V | 7 | |
| High-side MOSFET on-resistance | RDS_ON_HS | 95 | 150 | mΩ | IOUT = 1 A, VBIAS = VOUT = 3.3 V | 7 | |
| Low-side MOSFET on-resistance | RDS_ON_LS | 45 | 85 | mΩ | IOUT = 1 A, VBIAS = VOUT = 3.3 V | 7 | |
| PGOOD rising edge deglitch delay | tPGOOD_RISE | 80 | 140 | 200 | µs | 8 | |
| PGOOD falling edge deglitch delay | tPGOOD_FALL | 80 | 140 | 200 | µs | 8 | |
| Minimum switch on-time | tON-MIN | 65 | 95 | ns | 8 | ||
| Minimum switch off-time | tOFF-MIN | 95 | 130 | ns | 8 | ||
| Maximum switch on-time | tON-MAX | 3.8 | 8 | 11.4 | µs | HS timeout in dropout | 8 |
| Internal oscillator frequency | fOSC | 440 | 500 | 560 | kHz | RT = Open | 8 |
| Minimum adjustable frequency by RT or SYNC | fADJ | 270 | 300 | 330 | kHz | RT = 133 kΩ, 0.1% | 8 |
| Maximum adjustable frequency by RT or SYNC | fADJ | 1980 | 2200 | 2420 | kHz | RT = 17.4 kΩ, 0.1% | 8 |
| Junction-to-ambient thermal resistance | RθJA | 29.6 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 17.6 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 9.1 | °C/W | 6 | |||
| Junction-to-top characterization parameter | ψJT | 0.2 | °C/W | 6 | |||
| Junction-to-board characterization parameter | ψJB | 9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1 | °C/W | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 3. Minimize trace length to the FB pin net. Place both feedback resistors, RFBT and RFBB, close to the FB pin. Because the FB node is high impedance, maintain the copper area as small as possible. Rou | 42 |
CAD (KiCad official)
- Symbol:
LM76003RNPT - Footprint:
Package_DFN_QFN:Texas_RNP0030B_WQFN-30-1EP_4x6mm_P0.5mm_EP1.8x4.5mm - 3D model: 30-WFQFN Exposed Pad, generated on the KiCad land (body 4 x 6 mm, terminals on the pads, 0.8 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lm76003rnpt-etched.step/lm76003rnpt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm76003rnpt.step/lm76003rnpt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (59 pp, sha256
1ef4ab645f7e3202, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0). Land: footprint: KiCad Texas_RNP0030B_WQFN-30-1EP_4x6mm_P0.5mm_EP1.8x4.5mm, checked against datasheet pitch/body/pin count/ep/drawing (outline drawing RNP0030B; pitch 0.5 mm; body 4.0 x 6.0 mm; 31 terminals; exposed pad 1.8 x 4.5 mm, p.53).