main
Ray
Publish 0.1.0
46b2cfa
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335
{
"slug": "lm76003rnpr",
"version": "0.1.0",
"type": "component",
"description": "Texas Instruments DC-DC Converters, WQFN-30-EP(4x6). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
"tags": [
"component",
"power management (pmic)",
"lm76003rnpr",
"factory-2.0.0",
"extractor-text"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"lm76003rnpr.kicad_sym",
"lm76003rnpr.kicad_mod",
"lm76003rnpr.glb",
"lm76003rnpr.step",
"lm76003rnpr.lbr",
"docs/hero.png",
"docs/lm76003rnpr-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"lm76003rnpr-hero.glb",
"lm76003rnpr-hero.overlay.json"
],
"component": {
"mpn": "LM76003RNPR",
"manufacturer": "Texas Instruments",
"package": "WQFN-30-EP(4x6)",
"pin_count": 31,
"category": "Power Management (PMIC)",
"subcategory": "DC-DC Converters",
"datasheet": "https://www.ti.com/lit/ds/symlink/lm76003.pdf",
"parts": {
"symbol": "lm76003rnpr.kicad_sym",
"footprint": "lm76003rnpr.kicad_mod",
"model_3d": "lm76003rnpr-hero.glb",
"model_3d_plain": "lm76003rnpr.glb",
"model_3d_step": "lm76003rnpr-etched.step",
"model_3d_step_plain": "lm76003rnpr.step",
"lbr": "lm76003rnpr.lbr"
},
"distributor_links": {
"lcsc": "C470958",
"digikey": "296-49740-2-ND",
"mouser": "595-LM76003RNPR"
},
"distributor_check": {
"checked_at": "2026-11-21T15:37:02Z",
"source": "Component Ocean /api/assign-pns",
"digikey": {
"pn": "296-49740-2-ND",
"status": "found",
"lifecycle": "Active"
},
"mouser": {
"pn": "595-LM76003RNPR",
"status": "found"
}
},
"pins": [
{
"number": "1",
"name": "SW",
"type": "power_out",
"description": "Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor."
},
{
"number": "2",
"name": "SW",
"type": "power_out",
"description": "Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor."
},
{
"number": "3",
"name": "SW",
"type": "power_out",
"description": "Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor."
},
{
"number": "4",
"name": "SW",
"type": "power_out",
"description": "Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor."
},
{
"number": "5",
"name": "SW",
"type": "power_out",
"description": "Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor."
},
{
"number": "6",
"name": "BOOT",
"type": "passive",
"description": "Bootstrap capacitor connection for the high-side driver; connect a high-quality 470-nF capacitor from this pin to SW."
},
{
"number": "7",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "8",
"name": "VCC",
"type": "power_out",
"description": "Output of the internal bias supply used for internal control circuits; connect a high-quality 2.2-µF capacitor to GND, and TI does not recommend loading this pin with external circuitry."
},
{
"number": "9",
"name": "BIAS",
"type": "power_in",
"description": "Optional BIAS LDO supply input; tie to VOUT for 3.3 V ≤ VOUT ≤ 18 V or to an external 3.3-V or 5-V rail to improve efficiency, with a 1-µF capacitor to ground when used, and tie to ground when not in use."
},
{
"number": "10",
"name": "RT",
"type": "input",
"description": "Switching frequency setting pin; a resistor from this pin to ground sets the frequency, the default is 500 kHz if floating, and it must not be shorted to ground."
},
{
"number": "11",
"name": "SS/TRK",
"type": "input",
"description": "Soft-start control pin; leave floating for the 6.3-ms internal ramp, add a capacitor to ground to extend soft start, or drive an external ramp for tracking, and do not short to ground."
},
{
"number": "12",
"name": "FB",
"type": "input",
"description": "Feedback input for output voltage regulation, connected to a resistor divider; it must never be shorted to ground during operation."
},
{
"number": "13",
"name": "AGND",
"type": "power_in",
"description": "Analog ground and reference for internal references and logic; all electrical parameters are measured with respect to this pin and it connects to system ground."
},
{
"number": "14",
"name": "AGND",
"type": "power_in",
"description": "Analog ground and reference for internal references and logic; all electrical parameters are measured with respect to this pin and it connects to system ground."
},
{
"number": "15",
"name": "AGND",
"type": "power_in",
"description": "Analog ground and reference for internal references and logic; all electrical parameters are measured with respect to this pin and it connects to system ground."
},
{
"number": "16",
"name": "PGOOD",
"type": "output",
"description": "Open-drain power-good flag output that is high when VOUT regulation is OK and low on a fault or when EN is low; connect to a supply through a current-limiting resistor."
},
{
"number": "17",
"name": "SYNC/MODE",
"type": "input",
"description": "Synchronization and mode-setting input that must not float: tie to ground for DCM/PFM at light load, to logic high for forced PWM, or to an external clock to synchronize (triggered on the rising edge)."
},
{
"number": "18",
"name": "EN",
"type": "input",
"description": "Precision-enable input where high turns the regulator on and low turns it off; it must not float, can be tied to VIN, and allows adjustable UVLO via an external divider."
},
{
"number": "19",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "20",
"name": "PVIN",
"type": "power_in",
"description": "Supply input to the internal bias LDO and HS FET; connect to the input supply and input bypass capacitor CIN placed right next to this pin and PGND with short traces."
},
{
"number": "21",
"name": "PVIN",
"type": "power_in",
"description": "Supply input to the internal bias LDO and HS FET; connect to the input supply and input bypass capacitor CIN placed right next to this pin and PGND with short traces."
},
{
"number": "22",
"name": "PVIN",
"type": "power_in",
"description": "Supply input to the internal bias LDO and HS FET; connect to the input supply and input bypass capacitor CIN placed right next to this pin and PGND with short traces."
},
{
"number": "23",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "24",
"name": "PGND",
"type": "power_in",
"description": "Power ground connected internally to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT with the CIN path kept as short as possible."
},
{
"number": "25",
"name": "PGND",
"type": "power_in",
"description": "Power ground connected internally to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT with the CIN path kept as short as possible."
},
{
"number": "26",
"name": "PGND",
"type": "power_in",
"description": "Power ground connected internally to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT with the CIN path kept as short as possible."
},
{
"number": "27",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "28",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "29",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "30",
"name": "NC",
"type": "unconnected",
"description": "Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability."
},
{
"number": "31",
"name": "EP",
"type": "passive",
"description": "Exposed pad (from the footprint; not named in the datasheet pin table)."
}
],
"provenance": {
"extractor": "extract_pins 0.3",
"factory_chain": {
"factory": "2.0.0",
"extractor": "extract_pins 0.3",
"primary_model": "claude-haiku-5-5",
"primary_mode": "text",
"consensus_model": "claude-sonnet-5-5",
"consensus": "agreed",
"guards": "pin_guards 0.1: passed",
"guard_notes": [
"extractor flagged: Package hint says WQFN-30-EP(4x6); the datasheet gives the body as 6.00 mm x 4.00 mm for the RNP 30-",
"exposed pad 31 added from the footprint",
"dropped thermal pad ['EP'] absent from footprint"
],
"pages_sent": 12,
"cost_usd": 0.0631,
"at": "2026-11-21T15:36:53"
},
"datasheet": {
"url": "https://www.ti.com/lit/ds/symlink/lm76003.pdf",
"pages": 59,
"sha256": "1ef4ab645f7e3202",
"source_tier": "mfr",
"citation": "Texas Instruments datasheet"
},
"cad": "Adom_Gen derived land; symbol and 3D generated",
"pins": {
"total": 31,
"described": 31,
"cites_pages": true,
"refuses_to_fabricate": true
}
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"models_3d": [
{
"file": "lm76003rnpr.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
4.02,
6.02,
0.8
],
"zmin_mm": 0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "b454b4bc7b3ab9c7a9e574f6d64bc0890a00891212e3d0b8e421560eba41e969",
"checked": "2026-11-21",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "lm76003rnpr-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
4.02,
6.02,
0.8
],
"zmin_mm": 0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "65af1dfdfd826338da76bfcaf5c077e2edfeaa6884c6457a9da0712cd3c76917",
"checked": "2026-11-21",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
]
}
}