3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM53603AQPWPRQ1
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
LM53603AQPWPRQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Regulator switch node. Connect to power inductor. Connect pins 1 and 2 directly together at the PCB. |
| 2 | SW | output | Regulator switch node. Connect to power inductor. Connect pins 1 and 2 directly together at the PCB. |
| 3 | CBOOT | power_in | Bootstrap supply input for gate drivers. Connect a high quality 470 nF capacitor from this pin to SW. |
| 4 | VCC | power_out | Internal 3.15 V regulator output. Used as supply to internal control circuits. Do not connect to any external loads. Can be used as logic supply for control inputs. Connect a high quality 3.3 µF capacitor from this pin to GND. |
| 5 | BIAS | power_in | Input to internal voltage regulator. Connect to output voltage point. Do not ground. Connect a high quality 0.1 µF capacitor from this pin to GND. |
| 6 | SYNC | input | Synchronization input to regulator. Used to synchronize the regulator switching frequency to the system clock. When not used connect to GND; do not float. |
| 7 | FPWM | input | Mode control input to regulator. High = forced PWM (FPWM). Low = auto mode; automatic transition between PFM and PWM. Do not float. |
| 8 | RESET | output | Open drain reset output. Connect to suitable voltage supply through a current limiting resistor. High = power OK. Low = fault. RESET will go low when EN = low. |
| 9 | FB | input | Feedback input to regulator. Connect to output voltage sense point for fixed 5 V and 3.3 V output. Connect to feedback divider tap point for ADJ option. Do not float or ground. |
| 10 | AGND | power_in | Analog ground for regulator and system. All electrical parameters are measured with respect to this pin. Connect to EP and PGND on PCB. |
| 11 | EN | input | Enable input to the regulator. High = ON. Low = OFF. Can be connected directly to VIN. Do not float. |
| 12 | VIN | power_in | Input supply to the regulator. Connect a high quality bypass capacitor(s) from this pin to PGND. Connect pins 12 and 13 directly together at the PCB. |
| 13 | VIN | power_in | Input supply to the regulator. Connect a high quality bypass capacitor(s) from this pin to PGND. Connect pins 12 and 13 directly together at the PCB. |
| 14 | N/C | unconnected | This pin has no connection to the device. |
| 15 | PGND | power_in | Power ground to internal low side MOSFET. Connect to AGND and system ground. Connect pins 15 and 16 directly together at the PCB. |
| 16 | PGND | power_in | Power ground to internal low side MOSFET. Connect to AGND and system ground. Connect pins 15 and 16 directly together at the PCB. |
| 17 | EP | power_in | Exposed die attach paddle. Connect to ground plane for adequate heat sinking and noise reduction. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to AGND, PGND | -0.3 | 40 | V | 4 | |||
| SW to AGND, PGND | -0.3 | V | 4 | ||||
| CBOOT to SW | -0.3 | 3.6 | V | 4 | |||
| EN to AGND, PGND | -0.3 | 40 | V | 4 | |||
| BIAS to AGND, PGND | -0.3 | 16 | V | 4 | |||
| FB to AGND, PGND: fixed 5 V and 3.3 V | -0.3 | 16 | V | 4 | |||
| FB to AGND, PGND: ADJ | -0.3 | 5.5 | V | 4 | |||
| RESET to AGND, PGND | -0.3 | 8 | V | 4 | |||
| SYNC, FPWM to AGND, PGND | -0.3 | 5.5 | V | 4 | |||
| VCC to AGND, PGND | -0.3 | 4.2 | V | 4 | |||
| RESET Pin Current | -0.1 | 1.2 | mA | 4 | |||
| AGND to PGND | -0.3 | 0.3 | V | 4 | |||
| Storage temperature | Tstg | -40 | 150 | °C | 4 | ||
| Input voltage | 3.9 | 36 | V | 5 | |||
| Output voltage: Fixed 5 V | 0 | 5 | V | 5 | |||
| Output voltage: Fixed 3.3 V | 0 | 3.3 | V | 5 | |||
| Output voltage adjustment range: ADJ | 3.3 | 6 | V | 5 | |||
| Output current for LM53603-Q1 | 0 | 3 | A | 5 | |||
| RESET pin current | 0 | 1 | mA | 5 | |||
| Operating junction temperature | -40 | 150 | °C | 5 | |||
| Initial reference voltage accuracy | -1 | 1 | % | VIN = 3.8 V to 36 V, FPWM, TJ = 25°C, FB for 5 V and 3.3 V options | 6 | ||
| Initial reference voltage accuracy | -1.25 | 1.25 | % | VIN = 3.8 V to 36 V, FPWM | 6 | ||
| Reference voltage for ADJ option | VREF | 0.993 | 1 | 1.007 | V | VIN = 3.8 V to 36 V, FPWM, TJ = 25°C | 6 |
| Reference voltage for ADJ option | VREF | 0.99 | 1 | 1.01 | V | VIN = 3.8 V to 36 V, FPWM, TJ = -40°C to 125°C | 6 |
| Minimum input voltage to operate: Rising | VIN-operate | 3.2 | 3.95 | V | Rising | 6 | |
| Minimum input voltage to operate: Falling | VIN-operate | 2.9 | 3.55 | V | Falling | 6 | |
| Operating quiescent current | IQ | 8 | 13 | µA | VBIAS = 5 V, measured at VIN pin, TJ = -40°C to 125°C | 6 | |
| Current into the BIAS pin | IB | 47 | 78 | µA | VBIAS = 5 V, FPWM = 3.3 V | 6 | |
| RESET upper threshold voltage | 105 | 107 | 110 | % | Rising, % of nominal Vout | 6 | |
| RESET lower threshold voltage | VRESET | 92 | 94 | 96.5 | % | Falling, % of nominal Vout | 6 |
| Enable input threshold voltage: Rising | VEN | 1.7 | 2 | V | Rising | 6 | |
| Enable input threshold voltage: Hysteresis | VEN | 0.45 | 0.55 | V | 6 | ||
| Logic input high level on FPWM and SYNC pins | VIH | 1.5 | V | FPWM and SYNC pins | 6 | ||
| Logic input low level on FPWM and SYNC pins | VIL | 0.4 | V | FPWM and SYNC pins | 6 | ||
| High side switch current limit LM53603-Q1 | IHS | 4.5 | 6.2 | A | 6 | ||
| Low side switch current limit LM53603-Q1 | ILS | 3 | 3.6 | 4.3 | A | 7 | |
| High side MOSFET resistance (Rdson) | Rdson | 135 | 290 | mΩ | 7 | ||
| Low side MOSFET resistance (Rdson) | Rdson | 60 | 125 | mΩ | 7 | ||
| Switching frequency | FSW | 1.85 | 2.1 | 2.35 | MHz | VIN = 3.8 V to 18 V | 7 |
| Synchronizing frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | 7 | |
| Thermal shutdown threshold: Rising | TSD | 162 | 178 | °C | Rising | 7 | |
| Minimum switch on-time | TON | 50 | 80 | ns | VIN = 20 V | 8 | |
| Minimum switch off-time | TOFF | 125 | 200 | ns | VIN = 3.8 V | 8 | |
| Delay time to RESET high signal | TRESET-act | 2 | 3 | 4 | ms | 8 | |
| Glitch filter time for RESET function | TRESET-filter | 12 | 25 | 45 | µs | 8 | |
| Soft-start time | TSS | 1 | 2 | 3 | ms | 8 | |
| Junction-to-ambient thermal resistance | RθJA | 38.9 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 24.3 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 19.9 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.7 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
LM53603AQPWPRQ1 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm53603aqpwprq1-etched.step/lm53603aqpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm53603aqpwprq1.step/lm53603aqpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
b2d0d78814aaf2aa, retrieved 2026-10-06, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).