Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM53603AMPWPR

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

LM53603AMPWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output Regulator switch node driven by internal high-side and low-side switches connected to power inductor; connect pins 1 and 2 directly together at the PCB.
2 SW output Regulator switch node driven by internal high-side and low-side switches connected to power inductor; connect pins 1 and 2 directly together at the PCB.
3 CBOOT power_out Bootstrap supply output for gate drivers with voltage rating -0.3 to 3.6 V; connect a 470-nF capacitor from this pin to SW.
4 VCC power_out Internal 3.15-V regulator output used as supply to internal control circuits with nominal voltage 3.15 V (VBIAS = 3.3 V); do not connect to external loads.
5 BIAS power_in Input to internal voltage regulator connected to output voltage point with voltage rating -0.3 to 16 V; do not ground.
6 SYNC input Synchronization input to regulator used to synchronize switching frequency to system clock with frequency range 1.9 to 2.3 MHz; connect to GND when not used.
7 FPWM input Mode control input to regulator with logic levels VIH ≥ 1.5 V for forced PWM mode and VIL ≤ 0.4 V for automatic PFM/PWM mode; do not float.
8 RESET tri_state Open-drain reset output indicating power OK (high) or fault (low) with upper threshold 105% to 110% and lower threshold 92% to 96.5% of nominal output voltage.
9 FB input Feedback input to regulator connected to output voltage sense point for fixed outputs or feedback divider tap point for adjustable option with bias current 10 nA; do not float or ground.
10 AGND power_in Analog ground for regulator and system with respect to which all electrical parameters are measured; connect to EP and PGND on PCB.
11 EN input Enable input to regulator (high = ON, low = OFF) with rising threshold 1.7 to 2 V and falling shutdown voltage 0.8 V; can be connected directly to VIN.
12 VIN power_in Input supply to regulator with recommended range 3.9 to 36 V and absolute maximum -0.3 to 40 V; connect pins 12 and 13 directly together at the PCB.
13 VIN power_in Input supply to regulator with recommended range 3.9 to 36 V and absolute maximum -0.3 to 40 V; connect pins 12 and 13 directly together at the PCB.
14 N/C unconnected No connection to device.
15 PGND power_in Power ground to internal low-side MOSFET connected to AGND and system ground; connect pins 15 and 16 directly together at the PCB.
16 PGND power_in Power ground to internal low-side MOSFET connected to AGND and system ground; connect pins 15 and 16 directly together at the PCB.
17 EP power_in Exposed die attach paddle connected to ground plane for adequate heat sinking and noise reduction.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

CAD (KiCad official)

  • Symbol: LM53603AMPWPR
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm53603ampwpr-etched.step / lm53603ampwpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm53603ampwpr.step / lm53603ampwpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (40 pp, sha256 590d70f52aa0f37f, retrieved 2026-10-01, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF