3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM53601LQDSXRQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(3x3)
LM53601LQDSXRQ1 from Texas Instruments, in a WSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch node connected to output inductor; oscillates between ground and VIN during switching operation. |
| 2 | BOOT | input | Bootstrap capacitor connection for high-side gate driver; charged by internal diode when SW is low. |
| 3 | VCC | power_out | Internal 3.0V regulated supply for control circuits; bypass with 1.0-μF capacitor to AGND. |
| 4 | FB | input | Feedback input for output voltage regulation and VCC regulator power source; connect to output node with 10-nF bypass capacitor. |
| 5 | AGND | power_in | Analog ground reference for input signal and feedback voltage comparison. |
| 6 | RESET | output | Open-drain reset output indicating regulator status; high when regulator OK, low on fault or when EN is low. |
| 7 | EN | input | Regulator enable input; logic high enables operation, logic low disables; do not leave floating. |
| 8 | VIN | power_in | Input power supply; operates from 3.55V to 36V with transient capability up to 42V; connect bypass capacitors directly to GND. |
| 9 | SYNC/MODE | input | Mode control and synchronization input tolerant of voltages up to VIN; accepts external clock for PWM synchronization or ties high/low for PWM/AUTO mode selection. |
| 10 | GND | power_in | Ground return; bypass to VIN immediately adjacent to this pin. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | VIN | -0.3 | 42 | V | 5 | ||
| SW to GND | -0.3 | V | 5 | ||||
| BOOT to SW | -0.3 | 3.6 | V | 5 | |||
| EN to GND | EN | -0.3 | 42 | V | 5 | ||
| FB to GND (LM53600-Q1/LM53601-Q1 5.0 V fixed) | FB | -0.3 | 16 | V | 5.0 V fixed version | 5 | |
| RESET to GND | RESET | -0.3 | 8 | V | 5 | ||
| RESET sink current | 8 | mA | 5 | ||||
| SYNC/MODE to GND | SYNC/MODE | -0.3 | 42 | V | 5 | ||
| VCC | VCC | -0.3 | 3.6 | V | 5 | ||
| GND to AGND (fixed version only) | -1 | 2 | V | voltage durations of 1 µs or less | 5 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 5 | ||
| Input voltage range after startup | VIN | 3.8 | 36 | V | after startup | 5 | |
| Output voltage range, 5 V option | VOUT | 0 | 5.5 | V | 5 V option | 5 | |
| Load current range, LM53601-Q1 | 0 | 1000 | mA | LM53601-Q1 | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Initial output voltage accuracy | VFB | -1 | 1 | % | Vin= 3.8 V to 36 V Tj=25°C, Open Loop | 6 | |
| Initial output voltage accuracy | VFB | -1.5 | 1.5 | % | Vin= 3.8 V to 36 V, Open Loop | 6 | |
| Operating quiescent current; measured at VIN pin | IQ | 6.5 | µA | Vin= 13.5 V, Not switching Vbias= 5 V | 6 | ||
| Operating quiescent current; measured at VIN pin | IQ | 16 | µA | Vin= 13.5 V, Not switching Vbias= 5 V, Tj= 85°C | 6 | ||
| Bias current into FB pin (fixed versions) | IB | 46 | 80 | µA | Vin= 13.5 V, Not switching Vbias= 5 V, Mode = 0 V | 6 | |
| Shutdown quiescent current; measured at VIN pin | ISD | 1.8 | µA | EN = 0, VIN = 13.5 V Tj = 25°C | 6 | ||
| Shutdown quiescent current; measured at VIN pin | ISD | 3 | µA | EN = 0, VIN = 13.5 V Tj = 85°C | 6 | ||
| Minimum input voltage to operate | Vin_UVLO | 3.2 | 3.6 | 3.75 | V | Rising | 6 |
| Minimum input voltage hysteresis | Vin_UVLO_hyst | 0.2 | 0.3 | 0.35 | V | Hysteresis | 6 |
| RESET upper threshold voltage | Vreset_OV | 105 | 106.5 | 110 | % | Rising, % of Vout | 6 |
| RESET lower threshold voltage | Vreset_UV | 92 | 94 | 97 | % | Falling, % Vout | 6 |
| Low level RESET function output voltage | VOL | 0.4 | V | 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V, Tj = 25°C | 6 | ||
| Switching frequency | Fsw | 1.89 | 2.1 | 2.4 | MHz | VIN = 13.5 V, Center frequency with spread spectrum, PWM operation | 7 |
| Sync frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | Output setting + 1 V < VIN < 18 V | 7 |
| Sync input duty cycle range | DSYNC | 25 | 75 | % | High state input < 5.5 V and > 2.3 V | 7 | |
| SYNC/MODE input threshold voltage, input high (MODE=FPWM) | VSYNC/MODE | 1.5 | V | 7 | |||
| SYNC/MODE input threshold voltage, input low (MODE = V AUTO with diode emulation) | VSYNC/MODE | 0.4 | V | 7 | |||
| SYNC/MODE input hysteresis | 0.185 | 1 | V | 7 | |||
| Frequency span of spread spectrum operation | FSSS | -4 | 4 | % | 7 | ||
| Mode change transition time, to FPWM Mode | tMODE | 100 | µs | 20 mA load, VIN = 13.5 V | 7 | ||
| Mode change transition time, to AUTO Mode | tMODE | 60 | µs | 20-mA load, VIN = 13.5 V | 7 | ||
| High side switch current limit (LM53601-Q1) | IL_HS | 1.5 | 1.83 | 2.1 | A | Duty cycle approaches 0% | 7 |
| Low side switch current limit (LM53601-Q1) | IL_LS | 1 | 1.2 | 1.43 | A | 7 | |
| Enable input threshold voltage - rising | VEN | 1.7 | 2 | V | Enable rising | 7 | |
| Enable threshold hysteresis | VEN_HYST | 0.4 | 0.55 | V | 7 | ||
| Thermal shutdown rising threshold | TSD | 151 | 167 | 185 | °C | 8 | |
| Thermal shutdown falling threshold | TSDF | 140 | 157 | °C | 8 | ||
| Output voltage for 5-V option | Vout_5V | 4.9 | 5 | 5.1 | V | VIN = 5.8 V to 36 V, IOUT = Maximum recommended load current | 8 |
| Output voltage for 5-V option, Auto Mode | Vout_5V | 4.9 | 5.05 | 5.125 | V | VIN = 5.5 V to 36 V, IOUT=100 µA to 100 mA, typical value in Auto Mode | 8 |
| Minimum switch on time | ton | 50 | 80.5 | ns | VIN = 18 V, IOUT = 500 mA | 9 | |
| Minimum switch off time | toff | 90 | 125 | ns | IOUT = 500 mA | 9 | |
| Delay time to RESET high signal | treset_act | 4 | 6 | 8 | ms | 9 | |
| Soft-start time | tSS | 1.3 | 3 | 4.5 | ms | Time from first SW node pulse to Vref at 90%, VIN ≥4.2 V | 9 |
| Minimum input voltage for proper RESET function | Vreset_valid | 1.5 | V | 50 µA pull-up to RESET pin, EN = 0 V, Tj = 25°C | 6 | ||
| Negative current limit (LM53601-Q1) | IL_NEG | -0.7 | A | MODE/SYNC = High | 7 | ||
| Power switch on-resistance, high side MOSFET | Rdson | 220 | mΩ | 7 | |||
| Power switch on-resistance, low side MOSFET | Rdson | 200 | mΩ | 7 | |||
| Input current to VIN node of DC/DC (5 V output) | IQ_VIN | 30 | µA | VIN = 13.5 V, VOUT = 5 V, IOUT = 0 A | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 46.2 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 31.5 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 20.9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.1 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LM53601LQDSXRQ1 - Footprint:
Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.2x2mm - 3D model: WSON-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lm53601lqdsxrq1-etched.step/lm53601lqdsxrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm53601lqdsxrq1.step/lm53601lqdsxrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
d174c97c59a34282, retrieved 2026-10-03, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).