Generated by kicad-footprint-generator · KiCad file format 20260206
LM536013QDSXTQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(3x3)
LM536013QDSXTQ1 from Texas Instruments, in a WSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Regulator switch node that connects to the output inductor. |
| 2 | BOOT | input | High-side gate driver upper supply rail; connect a 100-nF capacitor from SW to BOOT, charged by an internal diode while SW is low. |
| 3 | VCC | power_out | Internal 3-V regulator output supplying the internal control circuits; connect a high-quality 1.0-µF capacitor from this pin to AGND for fixed versions. |
| 4 | FB | power_in | Fixed version feedback for the output voltage and power source for the VCC regulator; connect to the output node with a 10-nF bypass capacitor immediately adjacent to the pin. |
| 5 | AGND | power_in | Fixed version ground to which the input signals and FB are compared. |
| 6 | RESET | output | Open-drain reset output that is high when the regulator is OK and low on fault or when EN is low; RESET sink current is limited to 8 mA and it needs a current-limiting pull-up resistor. |
| 7 | EN | input | Enable input: high turns the regulator on and low turns it off; it can be connected to VIN and must not float. |
| 8 | VIN | power_in | Input supply to the regulator, with a recommended operating range of 3.8 V to 36 V; connect input bypass capacitors directly between this pin and GND. |
| 9 | SYNC/MODE | input | Multifunction mode input tolerant of voltages up to the input voltage; an external sync clock gives forced PWM synchronized at the rising edge, high gives forced PWM at the internal clock, and low gives AUTO mode with diode emulation; it must not float. |
| 10 | GND | power_in | Ground pin that must be bypassed to VIN immediately adjacent to this pin. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Initial output voltage accuracy (Tj=25C, open loop) | VFB | -1 | 1 | % | Vin= 3.8 V to 36 V Tj=25C, Open Loop | 6 | |
| Initial output voltage accuracy (open loop) | VFB | -1.5 | 1.5 | % | Vin= 3.8 V to 36 V, Open Loop | 6 | |
| Operating quiescent current (measured at VIN pin) | IQ | 6.5 | uA | Vin= 13.5 V, Not switching Vbias= 5 V | 6 | ||
| Operating quiescent current (measured at VIN pin), 85 C | IQ | 16 | uA | Vin= 13.5 V, Not switching Vbias= 5 V, Tj= 85C | 6 | ||
| Bias current into FB pin (fixed versions) | IB | 46 | 80 | uA | Vin= 13.5 V, Not switching Vbias= 5 V, Mode = 0 V | 6 | |
| Shutdown quiescent current (measured at VIN pin), 25 C | ISD | 1.8 | uA | EN = 0, VIN = 13.5 V Tj = 25C | 6 | ||
| Minimum input voltage to operate (rising) | Vin_UVLO | 3.2 | 3.6 | 3.75 | V | Rising | 6 |
| Minimum input voltage hysteresis | Vin_UVLO_hyst | 0.2 | 0.3 | 0.35 | V | Hysteresis | 6 |
| RESET upper threshold voltage | Vreset_OV | 105 | 106.5 | 110 | % | Rising, % of Vout | 6 |
| RESET lower threshold voltage | Vreset_UV | 92 | 94 | 97 | % | Falling, % Vout | 6 |
| Minimum input voltage for proper RESET function | Vreset_valid | 1.5 | V | 50 uA pull-up to RESET pin, EN = 0 V, Tj = 25C | 6 | ||
| Low level RESET output voltage | VOL | 0.4 | V | 50 uA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V, Tj = 25C | 6 | ||
| Switching frequency (without spread spectrum, PWM) | Fsw | 1.89 | 2.1 | 2.4 | MHz | VIN = 13.5 V, Without spread spectrum, PWM operation | 7 |
| Switching frequency at high input, 3.3-V fixed output | Fsw | 1 | MHz | VIN = 36 V, 3.3-V fixed output device and adjustable devices regardless of output voltage | 7 | ||
| Sync frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | Output setting + 1 V < VIN < 18 V | 7 |
| Sync input duty cycle range | DSYNC | 25 | 75 | % | High state input < 5.5 V and > 2.3 V | 7 | |
| SYNC/MODE input high threshold voltage | VSYNC/MODE | 1.5 | V | SYNC/MODE input high (MODE=FPWM) | 7 | ||
| SYNC/MODE input low threshold voltage | VSYNC/MODE | 0.4 | V | SYNC/MODE input low (MODE = VAUTO with diode emulation) | 7 | ||
| SYNC/MODE leakage current | ISYNC/MODE | 1 | uA | Vin = 13.5 V, VSYNC/MODE = 3.3 V | 7 | ||
| High side switch current limit (LM53601-Q1) | IL_HS | 1.5 | 1.83 | 2.1 | A | LM53601-Q1 Duty cycle approaches 0% | 7 |
| Low side switch current limit (LM53601-Q1) | IL_LS | 1 | 1.2 | 1.43 | A | LM53601-Q1 | 7 |
| Negative current limit (LM53601-Q1) | IL_NEG | -0.7 | A | MODE/SYNC = High, LM53601-Q1 | 7 | ||
| High side MOSFET Rdson | Rdson | 220 | mOhm | High side MOSFET Rdson | 7 | ||
| Low side MOSFET Rdson | Rdson | 200 | mOhm | Low side MOSFET Rdson | 7 | ||
| Enable threshold voltage - rising | VEN | 1.7 | 2 | V | Enable rising | 7 | |
| Enable threshold hysteresis | VEN_HYST | 0.4 | 0.55 | V | 7 | ||
| Thermal shutdown rising threshold | TSD | 151 | 167 | 185 | C | Thermal shutdown rising threshold | 8 |
| Thermal shutdown falling threshold | TSDF | 140 | 157 | C | Thermal shutdown falling threshold | 8 | |
| Thermal shutdown hysteresis | TSD_hyst | 10 | C | Thermal shutdown hysteresis | 8 | ||
| Maximum switch duty cycle | Dmax | 76 | % | Fsw = 2.1 MHz | 8 | ||
| Maximum switch duty cycle in frequency fold back | Dmax | 96 | % | While in frequency fold back | 8 | ||
| Minimum input voltage for full functionality at 500-mA load, after start-up | Vin_min | 3.55 | V | VOUT = 3.3 V | 8 | ||
| Minimum input voltage for full functionality at 100% of max rated load, after start-up | Vin_min | 3.8 | V | VOUT = 3.3 V | 8 | ||
| Output voltage for 3.3-V option | Vout_3_3V | 3.23 | 3.3 | 3.37 | V | VIN = 4.0 V to 36 V, IOUT = Maximum recommended load current | 8 |
| Output voltage for 3.3-V option, Auto Mode | Vout_3_3V | 3.23 | 3.33 | 3.39 | V | VIN = 3.8 V to 36 V, IOUT=100 uA to 100 mA, typical value in Auto Mode | 8 |
| Minimum input to output voltage differential, without inductor DCR drop | VDROP1 | 0.6 | V | VOUT=3.3 V, IOUT=1000 mA, +2/-3% output accuracy | 8 | ||
| Minimum input to output voltage differential to maintain FSW >= 1.85 MHz, without inductor DCR drop | VDROP2 | 2 | V | VOUT = 3.3 V, IOUT=1000 mA, FSW = 1.85 MHz, 2% regulation accuracy | 8 | ||
| Minimum switch on time | ton | 50 | 80.5 | ns | VIN = 18 V, IOUT = 500 mA | 9 | |
| Minimum switch off time | toff | 90 | 125 | ns | IOUT = 500 mA | 9 | |
| Delay time to RESET high signal | treset_act | 4 | 6 | 8 | ms | 9 | |
| Soft-start time | tSS | 1.3 | 3 | 4.5 | ms | Time from first SW node pulse to Vref at 90%, VIN >=4.2 V | 9 |
| Input voltage range after startup | 3.8 | 36 | V | after startup | 5 | ||
| Output voltage range 3.3 V | 0 | 3.63 | V | 3.3 V option | 5 | ||
| Load current range LM53601-Q1 | 0 | 1000 | mA | LM53601-Q1 | 5 | ||
| Operating junction temperature | -40 | 150 | C | 5 | |||
| VIN to GND | -0.3 | 42 | V | 5 | |||
| BOOT to SW | -0.3 | 3.6 | V | 5 | |||
| EN to GND | -0.3 | 42 | V | 5 | |||
| FB to GND, 3.3 V fixed version | -0.3 | 16 | V | LM53600-Q1/LM53601-Q1 - 3.3 V | 5 | ||
| RESET to GND | -0.3 | 8 | V | 5 | |||
| RESET sink current | 8 | mA | Do not exceed pin's voltage rating | 5 | |||
| SYNC/MODE to GND | -0.3 | 42 | V | 5 | |||
| VCC | -0.3 | 3.6 | V | 5 | |||
| GND to AGND (fixed version only) | -1 | 2 | V | Fixed version only, voltage durations of 1 us or less | 5 | ||
| Storage temperature | Tstg | -40 | 150 | C | 5 | ||
| Junction-to-ambient thermal resistance (DSX WSON) | RthetaJA | 46.2 | C/W | 6 | |||
| Junction-to-case (top) thermal resistance (DSX WSON) | RthetaJC | 31.5 | C/W | 6 | |||
| Junction-to-board thermal resistance (DSX WSON) | RthetaJB | 20.9 | C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance (DSX WSON) | RthetaJC(bot) | 4.1 | C/W | 6 |
CAD (KiCad official)
- Symbol:
LM536013QDSXTQ1 - Footprint:
Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.2x2mm - 3D model: WSON-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lm536013qdsxtq1-etched.step/lm536013qdsxtq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm536013qdsxtq1.step/lm536013qdsxtq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
e5b0cd2ded2271f2, retrieved 2026-11-02, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).