3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM5165XDRCR
Texas Instruments · DC-DC Converters · WSON-10-EP(3x3)
LM5165XDRCR from Texas Instruments, in a WSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | tri_state | Switching node internally connected to the drain of the high-side PMOS buck switch and drain of the low-side NMOS synchronous rectifier; connect to the switching side of the power inductor. |
| 2 | VIN | power_in | Regulator supply input pin to high-side power MOSFET and internal bias rail LDO; path from VIN to input capacitor must be as short as possible. |
| 3 | ILIM | input | Programming pin for current limit that selects one of four preset options when appropriate resistor is connected from ILIM to GND; short ILIM to GND for maximum current setting. |
| 4 | SS | input | Programming pin for soft-start time; if 100-kΩ resistor connected to GND, soft-start is disabled; if open, soft-start ramps in 900 µs; programmable with external capacitance. |
| 5 | RT | input | Mode selection and on-time programming pin for COT control; short to GND to select PFM operation, or connect resistor to GND to program on-time and set switching frequency. |
| 6 | PGOOD | tri_state | Power Good output flag pin connected to drain of internal NFET that holds pin low when FB or VOUT is below regulation target; use 10 kΩ to 100 kΩ pullup resistor to system voltage rail or VOUT (no higher than 12 V). |
| 7 | EN | input | Input pin of precision enable / UVLO comparator; converter is enabled when EN voltage is greater than 1.212 V. |
| 8 | VOUT | input | Feedback input to voltage regulation loop; VOUT pin connects internal feedback resistor divider to regulator output voltage for fixed 3.3-V and 5-V options. |
| 9 | HYS | tri_state | Drain of internal NFET that is turned off when EN input is greater than EN threshold; external resistor from HYS to EN pin UVLO resistor divider programs input UVLO hysteresis voltage. |
| 10 | GND | power_in | Regulator ground return. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage (VIN) | VIN | 3 | 65 | V | 4 | ||
| Enable input voltage | EN | -0.3 | 65 | V | 4 | ||
| PGOOD voltage | PGOOD | -0.3 | 12 | V | 4 | ||
| HYS voltage | HYS | -0.3 | 5.5 | V | 4 | ||
| Output current (COT mode) | IOUT (COT mode) | 0 | 150 | mA | 4 | ||
| Output current (PFM mode) | IOUT (PFM mode) | 0 | 100 | mA | 4 | ||
| Operating junction temperature | -40 | 150 | °C | 4 | |||
| VIN, EN to GND | -0.3 | 68 | V | 4 | |||
| SW to GND | -0.7 | V | 4 | ||||
| SW to GND 20-ns transient | -3 | V | 20-ns transient | 4 | |||
| PGOOD, VOUT to GND | -0.3 | 16 | V | Survives short to automotive battery voltage | 4 | ||
| HYS to GND | -0.3 | 7 | V | 4 | |||
| ILIM, SS, RT, FB to GND | -0.3 | 3.6 | V | 4 | |||
| Maximum junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| IQ-SHD VIN DC supply current, shutdown | IQ-SHD | 4.6 | 6 | µA | VEN = 0 V, TA = 25°C | 5 | |
| IQ-SLEEP VIN DC supply current, no load | IQ-SLEEP | 10.5 | 15 | µA | VFB = 1.5 V, TA = 25°C | 5 | |
| IQ-SLEEP-VINMAX VIN DC supply current, no load | IQ-SLEEP-VINMAX | 11 | 15 | µA | VFB = 1.5 V, VVIN = 65 V, TA = 25°C | 5 | |
| High-side peak current threshold (VSON-10) | ILIM1-VSON | 220 | 240 | 264 | mA | ILIM shorted to GND | 5 |
| High-side peak current threshold (VSON-10) | ILIM2-VSON | 155 | 180 | 205 | mA | RILIM = 24.9 kΩ | 5 |
| High-side peak current threshold (VSON-10) | ILIM3-VSON | 100 | 120 | 145 | mA | RILIM = 56.2 kΩ | 5 |
| High-side peak current threshold (VSON-10) | ILIM4-VSON | 48 | 60 | 75 | mA | RILIM ≥ 100 kΩ | 5 |
| VOUT 5-V DC setpoint (LM5165X) | VVOUT50 | 4.9 | 5 | 5.1 | V | LM5165X | 5 |
| Minimum VIN for valid PGOOD | VINMIN-PGOOD | 1.2 | 1.65 | V | VVIN falling, IPGOOD = 0.1 mA, VPGOOD < 0.5 V | 5 | |
| PGOOD on-resistance | RPGOOD | 80 | 200 | Ω | VFB = 1 V | 5 | |
| PGOOD off-state leakage current | IPGOOD | 10 | 100 | nA | VFB = 1.2 V, VPGOOD = 5.5 V | 5 | |
| Turnon threshold (VIN rising) | VIN-ON | 2.6 | 2.75 | 2.95 | V | VIN voltage rising | 5 |
| Turnoff threshold (VIN falling) | VIN-OFF | 2.35 | 2.45 | 2.6 | V | VIN voltage falling | 6 |
| Enable turnon threshold | VEN-ON | 1.163 | 1.212 | 1.262 | V | EN voltage rising | 6 |
| Enable turnoff threshold | VEN-OFF | 1.109 | 1.144 | 1.178 | V | EN voltage falling | 6 |
| EN shutdown threshold | VEN-SD | 0.3 | 0.6 | V | EN voltage falling | 6 | |
| HYS on-resistance | RHYS | 80 | 200 | Ω | VEN = 1 V | 6 | |
| HYS off-state leakage current | IHYS | 10 | 100 | nA | VEN = 1.5 V, VHYS = 5.5 V | 6 | |
| Junction-to-ambient thermal resistance | RθJA | 47.7 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 59.9 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 22.1 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 1 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 22.2 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
LM5165XDRCR - Footprint:
Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.2x2mm - 3D model: WSON-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lm5165xdrcr-etched.step/lm5165xdrcr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5165xdrcr.step/lm5165xdrcr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (49 pp, sha256
a339b608f69984d4, retrieved 2026-10-03, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).