main
History Download
Ray Publish 0.1.0 3268901

LM51581RTER

TI(德州仪器) · DC-DC Converters · WQFN-16(3x3)

LM51581RTER from TI(德州仪器), in a WQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PGND power_in Power ground pin, the source connection of the internal N-channel power MOSFET; connect to the power ground.
2 VCC power_out Output of the internal VCC regulator and supply input of the internal MOSFET driver; connect a 1-µF ceramic bypass capacitor from this pin to PGND.
3 BIAS power_in Supply voltage input to the VCC regulator; connect a bypass capacitor from this pin to PGND. Datasheet operating range is 3.2 V to 60 V (absolute maximum 65 V).
4 PGOOD output Open-drain power-good indicator that goes low if FB is below the undervoltage threshold (VUVTH); connect a pullup resistor to the system voltage rail.
5 RT input Switching frequency setting pin; the switching frequency is programmed by a single resistor between RT and AGND (100 kHz to 2.2 MHz range).
6 EN/UVLO/SYNC input Enable pin that shuts the converter down when below the enable threshold (VEN), also used for programmable UVLO through a voltage divider and as an external sync input via a negative pulse; must not be left floating and should connect to BIAS if unused.
7 AGND power_in Analog ground pin; connect to the analog ground plane through a wide and short path.
8 COMP output Output of the internal transconductance error amplifier; connect the loop compensation components between this pin and AGND.
9 FB input Inverting input of the error amplifier; connect a voltage divider to set the output voltage in boost, SEPIC or primary-side regulated flyback topologies, with the low-side resistor as close to AGND as possible.
10 SS input Soft-start time programming pin; an external capacitor with an internal current source sets the ramp rate of the error amplifier reference, with the capacitor ground connected to AGND.
11 MODE input Mode selection pin sampled at initial power-up: 0 V (or AGND) disables hiccup and spread spectrum, 370 mV (37.4 kΩ to AGND) enables both, 620 mV (62.0 kΩ) enables hiccup only, and >1 V (100 kΩ to AGND) enables spread spectrum only.
12 NC unconnected No internal electrical contact; leave unconnected.
13 SW output Switch pin, the drain connection of the internal N-channel power MOSFET; absolute maximum SW to AGND is 85 V DC with -6 V for 5 ns transients.
14 SW output Switch pin, the drain connection of the internal N-channel power MOSFET; absolute maximum SW to AGND is 85 V DC with -6 V for 5 ns transients.
15 NC unconnected No internal electrical contact; leave unconnected.
16 PGND power_in Power ground pin, the source connection of the internal N-channel power MOSFET; connect to the power ground.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer TI(德州仪器)
Package WQFN-16(3x3)
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
BIAS to AGND -0.3 65 V 6
UVLO to AGND -0.3 V max printed as VBIAS + 0.3 6
SS, RT to AGND -0.3 3.8 V 6
FB to AGND -0.3 4 V 6
MODE to AGND -0.3 3.8 V 6
PGND to AGND -0.3 0.3 V 6
VCC to AGND -0.3 5.8 V operating lifetime de-rated when pin voltage > 5.5 V 6
PGOOD to AGND -0.3 18 V 6
COMP to AGND -0.3 V 6
SW to AGND (DC) -0.3 85 V 6
SW to AGND (5-ns transient) -6 V 5-ns transient 6
Junction temperature, TJ TJ -40 150 °C 6
Storage temperature, Tstg Tstg -55 150 °C 6
VSUPPLY Boost converter input VSUPPLY 1.5 60 V when BIAS ≥ 3.2 V 6
VLOAD Boost converter output VLOAD 83 V min printed as VSUPPLY 6
VBIAS BIAS input VBIAS 3.2 60 V 6
VUVLO UVLO input VUVLO 0 60 V 6
VFB FB input VFB 0 4 V 6
ISW Switch current ISW 0 A max printed as 'See note (4)', limited by ILIM when TJ < TTSD 6
fSW Typical switching frequency fSW 100 2200 kHz 6
fSYNC Synchronization pulse frequency fSYNC 100 2200 kHz 6
TJ Operating junction temperature TJ -40 125 °C 6
BIAS shutdown current ISHUTDOWN(BIAS) 2.6 5 µA VBIAS = 12 V, VUVLO = 0 V 7
BIAS operating current IOPERATING(BIAS) 670 850 µA VBIAS = 12 V, VUVLO = 2.0 V, VFB = VREF, RT = 220 kΩ 7
VCC regulation VVCC-REG 4.66 4.9 5.14 V VBIAS = 8 V, IVCC = 18 mA 7
VCC UVLO threshold VVCC-UVLO(RISING) 3.05 3.1 3.15 V VCC rising 7
Enable threshold EN rising VEN(RISING) 0.4 0.52 0.7 V EN rising 7
Enable threshold EN falling VEN(FALLING) 0.33 0.49 0.63 V EN falling 7
UVLO / SYNC threshold UVLO rising VUVLO(RISING) 1.425 1.5 1.575 V UVLO rising 7
UVLO / SYNC threshold UVLO falling VUVLO(FALLING) 1.37 1.45 1.52 V UVLO falling 7
UVLO hysteresis current IUVLO 4 5 6 µA VUVLO = 1.6 V 7
FSW modulation (upper limit) 7.8 % 7
FSW modulation (lower limit) -7.8 % 7
Soft-start current ISS 9 10 11 µA 7
Switching frequency fsw1 85 100 115 kHz RT = 220 kΩ 7
Switching frequency fsw2 388 440 492 kHz RT = 49.3 kΩ 8
Switching frequency fsw3 1980 2200 2420 kHz RT = 9.09 kΩ 8
Maximum duty cycle limit DMAX1 80 85 90 % RT = 9.09 kΩ 8
Maximum duty cycle limit DMAX2 90 93 96 % RT = 220 kΩ 8
Internal MOSFET current limit LM51581 ILIM 1.63 1.875 2.12 A 8
FB reference VREF 0.99 1 1.01 V 8
COMP clamp voltage COMP rising 2.5 2.8 V VUVLO = 2.0 V 8
COMP clamp voltage COMP falling 1 1.1 V COMP falling 8
Overvoltage threshold FB rising (reference to VREF) VOVTH 107 110 113 % FB rising 8
Undervoltage threshold FB falling (reference to VREF) VUVTH 87 90 93 % FB falling 8
Internal MOSFET on-resistance rDS(ON) 133 290 mΩ VBIAS = 12 V 8
Internal MOSFET on-resistance rDS(ON) 138 300 mΩ VBIAS = 3.5 V 8
Junction-to-ambient thermal resistance RθJA 45.6 °C/W 7
Junction-to-case (top) thermal resistance RθJC(top) 44.8 °C/W 7
Junction-to-board thermal resistance RθJB 19.1 °C/W 7
Junction-to-case (bottom) thermal resistance RθJC(bot) 6.7 °C/W 7
Junction-to-top characterization parameter ΨJT 0.8 °C/W 7
Junction-to-board characterization parameter ΨJB 19.1 °C/W 7
Junction-to-ambient thermal resistance (LM5158EVM-BST) RθJA 32.7 °C/W LM5158EVM-BST board 7
Junction-to-top characterization parameter (LM5158EVM-BST) ΨJT 0.6 °C/W LM5158EVM-BST board 7
Junction-to-board characterization parameter (LM5158EVM-BST) ΨJB 15.1 °C/W LM5158EVM-BST board 7

CAD (KiCad official)

  • Symbol: LM51581RTER
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: WQFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: lm51581rter-etched.step / lm51581rter-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm51581rter.step / lm51581rter.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TI(德州仪器) datasheet (45 pp, sha256 9e8875f070157c1d, retrieved 2026-11-10, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF