3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM51561HPWPR
Texas Instruments · DC-DC Converters · HTSSOP-14-EP
LM51561HPWPR from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BIAS | power_in | Supply voltage input to the VCC regulator; connect bypass capacitor to PGND. |
| 2 | NC | unconnected | No electrical contact. |
| 3 | VCC | power_out | Output of internal VCC regulator and MOSFET driver supply voltage; connect ceramic bypass capacitor to PGND. |
| 4 | GATE | output | N-channel MOSFET gate drive output; connect directly to MOSFET gate through short, low inductance path. |
| 5 | PGND | power_in | Power ground pin; connect directly to ground connection of sense resistor through low inductance wide and short path. |
| 6 | AGND | power_in | Analog ground pin; connect directly to analog ground plane through wide and short path. |
| 7 | CS | input | Current sense input pin; connect to positive side of current sense resistor through short path. |
| 8 | COMP | output | Output of internal transconductance error amplifier; connect loop compensation components between pin and ground plane. |
| 9 | DITHOFF | input | Spread spectrum selection pin; connect to VCC to disable internal spread spectrum (clock dithering), connect to AGND to enable. |
| 10 | FB | input | Inverting input of error amplifier; connect voltage divider from output to set output voltage in boost/SEPIC/non-isolated flyback topologies. |
| 11 | SS | input | Soft-start time programming pin; external capacitor and internal current source set ramp rate of internal error amplifier reference during soft start. |
| 12 | RT | input | Switching frequency setting pin; switching frequency is programmed by single resistor between RT and AGND. |
| 13 | PGOOD | output | Power-good indicator open-drain output; goes low if FB is below undervoltage threshold. |
| 14 | EN/UVLO/SYNC | input | Undervoltage lockout programming pin; converter startup and shutdown levels programmed through resistor divider; supports external clock synchronization via negative pulse. |
| 15 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-14-EP |
| Category | Power Management (PMIC) |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| BIAS shutdown current | ISHUTDOWN(BIAS) | 2.6 | 5 | µA | VBIAS = 12 V, VUVLO = 0 V | 5 | |
| BIAS operating current | IOPERATING(BIAS) | 490 | 580 | µA | VBIAS = 12 V, VUVLO = 2.0 V, VFB = VREF, RT = 220 kΩ | 5 | |
| VCC regulation | VVCC-REG | 6.5 | 6.85 | 7 | V | VBIAS = 8 V, No load | 5 |
| VCC UVLO threshold | VVCC-UVLO(RISING) | 2.75 | 2.85 | 2.95 | V | VCC rising | 5 |
| VCC sourcing current limit | IVCC-CL | 35 | 110 | mA | VBIAS = 10 V, VVCC = 0 V | 5 | |
| Enable threshold | VEN(RISING) | 0.4 | 0.52 | 0.7 | V | EN rising | 5 |
| Enable threshold | VEN(FALLING) | 0.33 | 0.49 | 0.63 | V | EN falling | 6 |
| UVLO / SYNC threshold | VUVLO(RISING) | 1.425 | 1.5 | 1.575 | V | UVLO rising | 6 |
| UVLO / SYNC threshold | VUVLO(FALLING) | 1.37 | 1.45 | 1.52 | V | UVLO falling | 6 |
| UVLO hysteresis current | IUVLO | 4 | 5 | 6 | µA | VUVLO = 1.6 V | 6 |
| Clock dithering threshold | VDITHOFF(RISING) | 1.1 | 1.7 | 2.1 | V | DITHOFF rising, VBIAS = 4 V | 6 |
| Clock dithering threshold | VDITHOFF(FALLING) | 0.6 | 1.2 | 1.8 | V | DITHOFF falling, VBIAS = 4 V | 6 |
| Soft-start current | ISS | 9 | 10 | 11 | µA | 6 | |
| Switching frequency | fsw1 | 85 | 100 | 115 | kHz | RT = 220 kΩ, VBIAS = 4 V | 6 |
| Switching frequency | fsw2 | 1980 | 2200 | 2420 | kHz | RT = 9.09 kΩ, VBIAS = 4 V | 6 |
| Maximum duty cycle limit | DMAX1 | 80 | 85 | 90 | % | RT = 9.09 kΩ, VBIAS = 4 V | 6 |
| Maximum duty cycle limit | DMAX2 | 90 | 93 | 96 | % | RT = 220 kΩ, VBIAS = 4 V | 6 |
| Peak slope compensation current | ISLOPE | 22.5 | 30 | 37.5 | µA | RT = 220 kΩ | 6 |
| Current limit threshold (CS-PGND) | VCLTH | 93 | 100 | 107 | mV | 6 | |
| FB reference | VREF | 0.99 | 1 | 1.01 | V | 6 | |
| COMP clamp voltage (rising) | VCOMP-CLAMP | 2.5 | 2.8 | V | COMP rising (VUVLO = 2.0 V) | 6 | |
| COMP clamp voltage (falling) | VCOMP-CLAMP | 1 | 1.15 | V | COMP falling | 6 | |
| Over-voltage threshold (rising, relative to VREF) | VOVTH | 107 | 110 | 113 | % | FB rising (in reference to VREF) | 6 |
| Under-voltage threshold (falling, relative to VREF) | VUVTH | 87 | 90 | 93 | % | FB falling (in reference to VREF) | 6 |
| VBIAS operating range | VBIAS | 2.97 | 60 | V | VCC directly connected to BIAS: 2.97 V to 16 V; VCC supplied from internal VCC regulator: 3.5 V to 60 V | 5 | |
| VCC voltage | VVCC | 2.97 | 16 | V | Should be less than VBIAS + 0.3 V | 5 | |
| DITHOFF input | VDITHOFF | 0 | 16 | V | 5 | ||
| UVLO input | VUVLO | 0 | 60 | V | 5 | ||
| FB input | VFB | 0 | 4 | V | 5 | ||
| Typical switching frequency | fSW | 100 | 2200 | kHz | 5 | ||
| Synchronization pulse frequency | fSYNC | 100 | 2200 | kHz | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| BIAS to AGND | -0.3 | 65 | V | 4 | |||
| UVLO to AGND | -0.3 | V | 4 | ||||
| SS to AGND | -0.3 | 3.8 | V | 4 | |||
| RT to AGND | -0.3 | 3.8 | V | 4 | |||
| FB to AGND | -0.3 | 4 | V | 4 | |||
| CS to AGND (DC) | -0.3 | 0.3 | V | DC | 4 | ||
| CS to AGND (transient) | -1 | V | 50 ns transient | 4 | |||
| PGND to AGND | -0.3 | 0.3 | V | 4 | |||
| DITHOFF to AGND | -0.3 | 18 | V | 4 | |||
| VCC to AGND | -0.3 | 18 | V | 4 | |||
| GATE to AGND (transient) | -1 | V | 50 ns transient | 4 | |||
| PGOOD to AGND | -0.3 | 18 | V | 4 | |||
| COMP to AGND | -0.3 | V | 4 | ||||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 54.7 | °C/W | LM5156HEVM-FLY board | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 44.1 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 49.1 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 20.7 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 2 | °C/W | LM5156HEVM-FLY board | 5 | ||
| Junction-to-top characterization parameter | ψJT | 2.3 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 17.3 | °C/W | LM5156HEVM-FLY board | 5 | ||
| Junction-to-board characterization parameter | ψJB | 20.7 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 7.9 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
LM51561HPWPR - Footprint:
Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)
- 3D model files:
lm51561hpwpr-etched.step/lm51561hpwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm51561hpwpr.step/lm51561hpwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (47 pp, sha256
1c2afe6d19f818b2, retrieved 2026-10-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).