main
History Download
Ray Publish 0.1.0 576abd3

LM5155DSST

Texas Instruments · DC-DC Controllers · WSON-12-EP(2x3)

LM5155DSST from Texas Instruments, in a WSON-12-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BIAS power_in Supply voltage input to the VCC regulator, which should be bypassed with a capacitor to PGND; the datasheet allows BIAS up to 45 V (50 V absolute maximum).
2 VCC power_out Output of the internal VCC regulator and supply input of the MOSFET driver, which requires a ceramic bypass capacitor to PGND and is limited to 18 V (absolute maximum).
3 GATE output N-channel MOSFET gate drive output, to be connected directly to the MOSFET gate through a short, low-inductance path, with 1.5-A peak drive capability.
4 PGND power_in Power ground pin, to be connected directly to the sense resistor ground through a low-inductance, wide, and short path.
5 CS input Current sense input, connected to the positive side of the current sense resistor through a short path; DC range is -0.3 V to 0.3 V to AGND.
6 COMP output Output of the internal transconductance error amplifier, with loop compensation components connected between this pin and PGND.
7 AGND power_in Analog ground pin, to be connected to the analog ground plane through a wide and short path.
8 FB input Inverting input of the error amplifier, fed by a voltage divider from the output in boost/SEPIC topologies with the low-side resistor returned to AGND; absolute maximum 3.8 V to AGND.
9 SS input Soft-start time programming pin, where an external capacitor with an internal current source sets the error amplifier reference ramp rate, with the capacitor returned to AGND.
10 RT input Switching frequency setting pin, programmed by a single resistor between RT and AGND to set frequencies from 100 kHz to 2.2 MHz.
11 PGOOD output Open-drain power-good indicator that goes low when FB is below the undervoltage threshold, requiring a pullup resistor to the system rail; absolute maximum 18 V to AGND.
12 UVLO/EN/SYNC input Undervoltage lockout programming pin, set by a resistor divider from the supply, which also accepts a negative pulse for clock synchronization, must not be left floating, and should be connected to BIAS if unused.
13 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-12-EP(2x3)
Category Power Supply Chip
Pins 13

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
BIAS to AGND -0.3 50 V 5
UVLO to AGND -0.3 V max VBIAS+0.3 V 5
SS to AGND -0.3 3.8 V pin not specified to have external voltage applied 5
RT to AGND -0.3 3.8 V pin not specified to have external voltage applied 5
FB to AGND -0.3 3.8 V 5
CS to AGND -0.3 0.3 V DC 5
CS to AGND -1 V 100ns transient 5
CS to AGND -2 V 20ns transient 5
PGND to AGND -0.3 0.3 V 5
VCC to AGND -0.3 18 V 18 V or VBIAS + 0.3 V whichever is lower 5
GATE to AGND -1 V 100ns transient 5
GATE to AGND -2 V 50ns transient 5
PGOOD to AGND -0.3 18 V 5
COMP to AGND -0.3 V 5
Junction temperature TJ -40 150 °C 5
Storage temperature Tstg -55 150 °C 5
Bias input VBIAS 2.97 45 V 2.97 V to 16 V when VCC is connected to BIAS; 3.5 V to 45 V when VCC is supplied from internal regulator 6
VCC voltage VVCC 2.97 16 V pin voltage should be less than VBIAS + 0.3 V 6
UVLO input VUVLO 0 45 V 6
FB input VFB 0 3.7 V 6
Typical switching frequency fSW 100 2200 kHz 6
Synchronization pulse frequency fSYNC 100 2200 kHz 6
Operating junction temperature TJ -40 125 °C 6
BIAS shutdown current ISHUTDOWN(BIAS) 2.6 5 uA VBIAS = 12 V, VUVLO = 0 V 6
BIAS operating current IOPERATING(BIAS) 480 540 uA VBIAS = 12 V, VUVLO = 2 V, VFB = VREF, RT = 220 kΩ 6
VCC regulation VVCC-REG 6.5 6.85 7 V VBIAS = 8 V, No load 6
VCC regulation 6.5 V VBIAS = 8 V, IVCC = 35 mA 6
VCC UVLO threshold VVCC-UVLO(RISING) 2.75 2.85 2.95 V VCC rising 6
VCC UVLO hysteresis 0.063 V VCC falling 6
VCC sourcing current limit IVCC-CL 35 105 mA VBIAS = 10 V, VVCC = 0 V 6
Enable threshold VEN(RISING) 0.4 0.52 0.7 V EN rising 6
Enable threshold VEN(FALLING) 0.33 0.49 0.63 V EN falling 6
Enable hysteresis VEN(HYS) 0.03 V EN falling 7
UVLO / SYNC threshold VUVLO(RISING) 1.425 1.5 1.575 V UVLO rising 7
UVLO / SYNC threshold VUVLO(FALLING) 1.37 1.45 1.52 V UVLO falling 7
UVLO / SYNC threshold hysteresis VUVLO(HYS) 0.05 V UVLO falling 7
UVLO hysteresis current IUVLO 4 5 6 uA VUVLO = 1.6 V 7
Soft-start current ISS 9 10 11 uA 7
SS pull-down switch RDSON 55 Ω 7
Switching frequency fsw1 85 100 115 kHz RT = 220 kΩ 7
Switching frequency fsw2 1980 2200 2420 kHz RT = 9.09 kΩ 7
Minimum on-time tON(MIN) 50 ns RT = 9.09 kΩ 7
Maximum duty cycle limit DMAX1 80 85 90 % RT = 9.09 kΩ 7
Maximum duty cycle limit DMAX2 90 93 96 % RT = 220 kΩ 7
Peak slope compensation current ISLOPE 22.5 30 37.5 uA RT = 220 kΩ 7
Current Limit threshold (CS-PGND) VCLTH 93 100 107 mV 7
FB reference VREF 0.99 1 1.01 V LM5155, LM51551 7
Transconductance Gm 2 mA/V 7
COMP sourcing current 180 uA VCOMP = 1.2 V 7
COMP clamp voltage 2.5 2.8 V COMP rising (VUVLO = 2.0V) 7
COMP clamp voltage 1 1.1 V COMP falling 7
Over-voltage threshold VOVTH 107 110 113 % FB rising (reference to VREF) 7
Over-voltage threshold VOVTH 105 % FB falling (reference to VREF) 7
PGOOD pull-down switch RDSON 90 Ω 1 mA sinking 7
Undervoltage threshold VUVTH 87 90 93 % FB falling (reference to VREF) 7
Undervoltage threshold VUVTH 95 % FB rising (reference to VREF) 7
MOSFET driver high-state voltage drop 0.25 V 100 mA sinking 7
MOSFET driver low-state voltage drop 0.15 V 100 mA sourcing 7
Thermal shutdown threshold TTSD 175 °C Temperature rising 7
Thermal shutdown hysteresis 15 °C 7
Junction-to-ambient thermal resistance RθJA 63.7 °C/W 6
Junction-to-case (top) thermal resistance RθJC(top) 61 °C/W 6
Junction-to-board thermal resistance RθJB 32.1 °C/W 6
Junction-to-top characterization parameter ψJT 2.3 °C/W 6
Junction-to-board characterization parameter ψJB 31.9 °C/W 6
Junction-to-case (bottom) thermal resistance RθJC(bot) 11.2 °C/W 6

CAD (KiCad official)

  • Symbol: LM5155DSST
  • Footprint: Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65
  • 3D model: WSON-12-EP(2x3) (KiCad packages3D, STEP)
  • 3D model files: lm5155dsst-etched.step / lm5155dsst-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5155dsst.step / lm5155dsst.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (48 pp, sha256 e65e47f61e64e3c3, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF