main
Ray
Publish 0.1.0
ce805cd
LM5148RGYR
TEXAS INSTRUMENTS · DC-DC Converters · VQFN-24(5.5x3.5)
LM5148RGYR from TEXAS INSTRUMENTS, in a VQFN-24(5.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 2 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 3 | CNFG | input | Connect a resistor to ground to set primary/secondary, spread spectrum enable/disable, or interleaved operation; CNFG to AGND is rated -0.3 V to 5.5 V. |
| 4 | RT | input | Frequency programming pin; a resistor from RT to AGND sets the oscillator frequency between 100 kHz and 2.2 MHz. |
| 5 | EXTCOMP | output | Transconductance error amplifier output; if used, connect the compensation network from EXTCOMP to AGND. |
| 6 | FB | input | Feedback input with a 0.8 V regulation voltage; tie to VDDA for 3.3 V, use 24.9 kΩ or 49.9 kΩ to VDDA for 5 V or 12 V, or use a divider from VOUT for 0.8 V to 55 V. |
| 7 | AGND | power_in | Analog ground connection and return for the internal voltage reference and analog circuits. |
| 8 | VDDA | power_out | Internal analog bias regulator output; connect a ceramic decoupling capacitor from VDDA to AGND. |
| 9 | VCC | power_out | VCC bias supply pin; connect a ceramic capacitor between VCC and PGND. |
| 10 | PGND | power_in | Power ground connection for the low-side MOSFET gate driver. |
| 11 | LO | output | Low-side power MOSFET gate driver output; LO to PGND is rated -0.3 V to VVCC + 0.3 V. |
| 12 | VIN | power_in | Supply voltage input for the VCC regulator; recommended input supply range is 3.5 V to 80 V. |
| 13 | HO | output | High-side power MOSFET gate driver output, referenced to SW. |
| 14 | SW | passive | Switching node of the buck regulator and high-side gate driver return; connect to the bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain. |
| 15 | CBOOT | power_out | High-side driver supply for bootstrap gate drive; CBOOT to SW is rated -0.3 V to 5.25 V in recommended conditions. |
| 16 | VCCX | power_in | Optional external bias supply input; if VCCX exceeds 4.3 V, it is connected internally to VCC and the internal VCC regulator is disabled. |
| 17 | PG/SYNCOUT | output | Open-collector output that goes low when VOUT is outside the specified regulation window; in dual-phase mode the primary provides a 180° phase-shifted SYNCOUT. |
| 18 | PFM/SYNC | input | Connect to VDDA to enable diode emulation, to AGND for forced PWM mode, or apply an external clock to synchronize the internal oscillator. |
| 19 | EN | input | Active-high precision enable with a rising threshold of 1 V and 10 µA hysteresis current; below 0.5 V the device is in shutdown unless a SYNC signal is present. |
| 20 | ISNS+ | input | Current sense amplifier input; connect to the inductor side of the external sense resistor using a low-current Kelvin connection. |
| 21 | VOUT | input | Output voltage sense and current sense amplifier input; connect to the output side of the current sense resistor. |
| 22 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 23 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 24 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TEXAS INSTRUMENTS |
| Package | VQFN-24(5.5x3.5) |
| Category | Power Management (PMIC) |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VOUT, ISNS+ to AGND output voltage | -0.3 | 60 | V | 5 | |||
| VOUT to ISNS+ | -0.3 | 0.3 | V | 5 | |||
| VIN to PGND input voltage | -0.3 | 85 | V | 5 | |||
| SW to PGND | -0.3 | 85 | V | 5 | |||
| SW to PGND transient | -5 | V | transient < 20 ns | 5 | |||
| CBOOT to SW | -0.3 | 6.5 | V | 5 | |||
| CBOOT to SW transient | -2 | V | transient < 20 ns | 5 | |||
| HO to SW | -0.3 | V | max VHB + 0.3 V | 5 | |||
| HO to SW transient | -5 | V | transient < 20 ns | 5 | |||
| LO to PGND | -0.3 | V | max VVCC + 0.3 V | 5 | |||
| LO to PGND transient | -1.5 | V | transient < 20 ns | 5 | |||
| EN to PGND | -0.3 | 85 | V | 5 | |||
| VCC, VCCX, VDDA, PG, FB, PFM/SYNC, RT, EXTCOMP to AGND | -0.3 | 6.5 | V | 5 | |||
| CNFG to AGND | -0.3 | 5.5 | V | 5 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 5 | ||
| VIN Input supply voltage range | VIN | 3.5 | 80 | V | 5 | ||
| VOUT Output voltage range | VOUT | 0.8 | 55 | V | 5 | ||
| CBOOT to SW | -0.3 | 5 | 5.25 | V | 5 | ||
| FB, EXTCOMP, RT, CNFG to AGND | -0.3 | 5.25 | V | 5 | |||
| EN to PGND | -0.3 | 80 | V | 5 | |||
| VCC, VCCX, VDDA to PGND | -0.3 | 5 | 5.25 | V | 5 | ||
| VOUT, ISNS+ to PGND | -0.3 | 55 | V | 5 | |||
| PGND to AGND | -0.3 | 0.3 | V | 5 | |||
| Junction-to-ambient thermal resistance RGY (VQFN) | RθJA | 37.3 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 5.6 | °C/W | 6 | |||
| Sleep current, 3.3 V | ISLEEP1 | 9.5 | 19.7 | µA | 1.03 V ≤ VEN ≤ 80 V, VVOUT = 3.3 V, in regulation, no-load, not switching, VPFM/SYNC = VDDA | 6 | |
| Sleep current, 5 V | ISLEEP2 | 9.9 | 19.9 | µA | 1.03 V ≤ VEN ≤ 80 V, VVOUT = 5.0 V, in regulation, no-load, not switching, VPFM/SYNC = VDDA | 6 | |
| VIN shutdown current | IQ-VIN1 | 2.3 | 3.8 | µA | VEN = 0 V | 6 | |
| Enable voltage rising threshold | VEN-HIGH | 0.95 | 1 | 1.05 | V | VEN rising, enable switching | 6 |
| Enable hysteresis | IEN-HYS | -12 | -10 | -8 | µA | VEN = 1.1 V | 6 |
| VCC regulation voltage | VVCC-REG | 4.7 | 5 | 5.3 | V | IVCC = 0 mA to 100 mA | 6 |
| VCC UVLO rising threshold | VVCC-UVLO | 3.3 | 3.4 | 3.5 | V | 6 | |
| Internal LDO short-circuit current limit | IVCC-REG | 115 | 170 | mA | 6 | ||
| VDDA regulation voltage | VVDDA-REG | 4.75 | 5 | 5.25 | V | 6 | |
| VDDA UVLO rising | VVDDA-UVLO | 3 | 3.2 | 3.3 | V | VVCC rising, VVCCX = 0 V | 6 |
| VCCX rising threshold | VVCCX-ON | 4.1 | 4.3 | 4.4 | V | 6 | |
| Regulated FB voltage | VREF | 795 | 800 | 808 | mV | 6 | |
| 3.3-V output voltage setpoint, internal compensation | VOUT-3.3V-INT | 3.267 | 3.3 | 3.33 | V | RFB = 0 Ω, VIN = 3.8 V to 80 V, internal compensation | 6 |
| 3.3-V output voltage setpoint, external compensation | VOUT-3.3V-EXT | 3.267 | 3.3 | 3.33 | V | RFB = 0 Ω, VIN = 3.8 V to 80 V, external compensation | 7 |
| 5-V output voltage setpoint, internal compensation | VOUT-5V-INT | 4.95 | 5 | 5.05 | V | RFB = 24.9 kΩ, VIN = 5.5 V to 80 V, internal compensation | 7 |
| 5-V output voltage setpoint, external compensation | VOUT-5V-EXT | 4.95 | 5 | 5.05 | V | RFB = 24.9 kΩ, VIN = 5.5 V to 80 V, external compensation | 7 |
| 12-V output setpoint, internal compensation | VOUT-12V-INT | 11.88 | 12 | 12.12 | V | RFB = 48.7 kΩ, VIN = 24 V to 80 V, internal compensation | 7 |
| 12-V output setpoint, external compensation | VOUT-12V-EXT | 11.88 | 12 | 12.12 | V | RFB = 48.7 kΩ, VIN = 24 V to 80 V, external compensation | 7 |
| 5-V output select | RFB-OPT1 | 23 | 25 | 27 | kΩ | 7 | |
| 12-V output select | RFB-OPT2 | 47 | 50 | 53 | kΩ | 7 | |
| EA transconductance, external compensation | gm-EXTERNAL | 1020 | 1200 | µS | FB to COMP | 7 | |
| EA transconductance, internal compensation | gm-INTERNAL | 10 | 30 | µS | EXTCOMP 10 kΩ to VDDA | 7 | |
| Frequency sync range | FSYNCIN | 1.74 | 2.7 | MHz | RRT = 9.52 kΩ, ±20% of the nominal oscillator frequency | 7 | |
| Switching frequency 2 | FSW2 | 1.98 | 2.2 | 2.42 | MHz | VIN = 12 V, RRT = 9.52 kΩ to AGND | 7 |
| Power Good UV trip level | VPG-UV | 90 | 92 | 94 | % | Falling with respect to the regulated voltage | 7 |
| Power Good OV trip level | VPG-OV | 108 | 110 | 112 | % | Rising with respect to the regulation voltage | 7 |
| Internal fixed soft-start time | tSS-INT | 1.9 | 3 | 4.6 | ms | 8 | |
| Current limit threshold | VCS-TH | 49 | 60 | 73 | mV | Measured from ISNS+ to VOUT | 8 |
| CS amplifier gain | GCS | 9 | 10 | 10.8 | V/V | 8 | |
| Primary, no spread spectrum | RCONF-OPT1 | 28.7 | 29.4 | 31 | kΩ | 8 | |
| Primary, with spread spectrum | RCONF-OPT2 | 40.2 | 41.2 | 43.2 | kΩ | 8 | |
| Primary, interleaved, no spread spectrum | RCONF-OPT3 | 53.6 | 54.9 | 57.6 | kΩ | 8 | |
| Primary, interleaved, with spread spectrum | RCONF-OPT4 | 69.8 | 71.5 | 73.2 | kΩ | 9 | |
| Secondary | RCONF-OPT5 | 87 | 90.9 | 93.1 | kΩ | 9 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • Connect the MOSFETs (switch node) directly to the inductor terminal with short copper connections (without | 57 |
CAD (Adom-generated)
- Symbol:
LM5148RGYR - Footprint:
Adom_Gen:TEXAS_INSTRUMENTS_LM5148_38543a - 3D model: generated to fit the land (STEP)
- 3D model files:
lm5148rgyr-etched.step/lm5148rgyr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5148rgyr.step/lm5148rgyr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TEXAS INSTRUMENTS datasheet (70 pp, sha256
bdea4391ef5e5cfa, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
# LM5148RGYR
**TEXAS INSTRUMENTS** · DC-DC Converters · VQFN-24(5.5x3.5)
LM5148RGYR from TEXAS INSTRUMENTS, in a VQFN-24(5.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 2 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 3 | CNFG | input | Connect a resistor to ground to set primary/secondary, spread spectrum enable/disable, or interleaved operation; CNFG to AGND is rated -0.3 V to 5.5 V. |
| 4 | RT | input | Frequency programming pin; a resistor from RT to AGND sets the oscillator frequency between 100 kHz and 2.2 MHz. |
| 5 | EXTCOMP | output | Transconductance error amplifier output; if used, connect the compensation network from EXTCOMP to AGND. |
| 6 | FB | input | Feedback input with a 0.8 V regulation voltage; tie to VDDA for 3.3 V, use 24.9 kΩ or 49.9 kΩ to VDDA for 5 V or 12 V, or use a divider from VOUT for 0.8 V to 55 V. |
| 7 | AGND | power_in | Analog ground connection and return for the internal voltage reference and analog circuits. |
| 8 | VDDA | power_out | Internal analog bias regulator output; connect a ceramic decoupling capacitor from VDDA to AGND. |
| 9 | VCC | power_out | VCC bias supply pin; connect a ceramic capacitor between VCC and PGND. |
| 10 | PGND | power_in | Power ground connection for the low-side MOSFET gate driver. |
| 11 | LO | output | Low-side power MOSFET gate driver output; LO to PGND is rated -0.3 V to VVCC + 0.3 V. |
| 12 | VIN | power_in | Supply voltage input for the VCC regulator; recommended input supply range is 3.5 V to 80 V. |
| 13 | HO | output | High-side power MOSFET gate driver output, referenced to SW. |
| 14 | SW | passive | Switching node of the buck regulator and high-side gate driver return; connect to the bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain. |
| 15 | CBOOT | power_out | High-side driver supply for bootstrap gate drive; CBOOT to SW is rated -0.3 V to 5.25 V in recommended conditions. |
| 16 | VCCX | power_in | Optional external bias supply input; if VCCX exceeds 4.3 V, it is connected internally to VCC and the internal VCC regulator is disabled. |
| 17 | PG/SYNCOUT | output | Open-collector output that goes low when VOUT is outside the specified regulation window; in dual-phase mode the primary provides a 180° phase-shifted SYNCOUT. |
| 18 | PFM/SYNC | input | Connect to VDDA to enable diode emulation, to AGND for forced PWM mode, or apply an external clock to synchronize the internal oscillator. |
| 19 | EN | input | Active-high precision enable with a rising threshold of 1 V and 10 µA hysteresis current; below 0.5 V the device is in shutdown unless a SYNC signal is present. |
| 20 | ISNS+ | input | Current sense amplifier input; connect to the inductor side of the external sense resistor using a low-current Kelvin connection. |
| 21 | VOUT | input | Output voltage sense and current sense amplifier input; connect to the output side of the current sense resistor. |
| 22 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 23 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 24 | NC | unconnected | Not internally connected; connect to GND at the exposed pad to improve heat spreading. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TEXAS INSTRUMENTS |
| Package | VQFN-24(5.5x3.5) |
| Category | Power Management (PMIC) |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VOUT, ISNS+ to AGND output voltage | | -0.3 | | 60 | V | | 5 |
| VOUT to ISNS+ | | -0.3 | | 0.3 | V | | 5 |
| VIN to PGND input voltage | | -0.3 | | 85 | V | | 5 |
| SW to PGND | | -0.3 | | 85 | V | | 5 |
| SW to PGND transient | | -5 | | | V | transient < 20 ns | 5 |
| CBOOT to SW | | -0.3 | | 6.5 | V | | 5 |
| CBOOT to SW transient | | -2 | | | V | transient < 20 ns | 5 |
| HO to SW | | -0.3 | | | V | max VHB + 0.3 V | 5 |
| HO to SW transient | | -5 | | | V | transient < 20 ns | 5 |
| LO to PGND | | -0.3 | | | V | max VVCC + 0.3 V | 5 |
| LO to PGND transient | | -1.5 | | | V | transient < 20 ns | 5 |
| EN to PGND | | -0.3 | | 85 | V | | 5 |
| VCC, VCCX, VDDA, PG, FB, PFM/SYNC, RT, EXTCOMP to AGND | | -0.3 | | 6.5 | V | | 5 |
| CNFG to AGND | | -0.3 | | 5.5 | V | | 5 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -55 | | 150 | °C | | 5 |
| VIN Input supply voltage range | VIN | 3.5 | | 80 | V | | 5 |
| VOUT Output voltage range | VOUT | 0.8 | | 55 | V | | 5 |
| CBOOT to SW | | -0.3 | 5 | 5.25 | V | | 5 |
| FB, EXTCOMP, RT, CNFG to AGND | | -0.3 | | 5.25 | V | | 5 |
| EN to PGND | | -0.3 | | 80 | V | | 5 |
| VCC, VCCX, VDDA to PGND | | -0.3 | 5 | 5.25 | V | | 5 |
| VOUT, ISNS+ to PGND | | -0.3 | | 55 | V | | 5 |
| PGND to AGND | | -0.3 | | 0.3 | V | | 5 |
| Junction-to-ambient thermal resistance RGY (VQFN) | RθJA | | 37.3 | | °C/W | | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 5.6 | | °C/W | | 6 |
| Sleep current, 3.3 V | ISLEEP1 | | 9.5 | 19.7 | µA | 1.03 V ≤ VEN ≤ 80 V, VVOUT = 3.3 V, in regulation, no-load, not switching, VPFM/SYNC = VDDA | 6 |
| Sleep current, 5 V | ISLEEP2 | | 9.9 | 19.9 | µA | 1.03 V ≤ VEN ≤ 80 V, VVOUT = 5.0 V, in regulation, no-load, not switching, VPFM/SYNC = VDDA | 6 |
| VIN shutdown current | IQ-VIN1 | | 2.3 | 3.8 | µA | VEN = 0 V | 6 |
| Enable voltage rising threshold | VEN-HIGH | 0.95 | 1 | 1.05 | V | VEN rising, enable switching | 6 |
| Enable hysteresis | IEN-HYS | -12 | -10 | -8 | µA | VEN = 1.1 V | 6 |
| VCC regulation voltage | VVCC-REG | 4.7 | 5 | 5.3 | V | IVCC = 0 mA to 100 mA | 6 |
| VCC UVLO rising threshold | VVCC-UVLO | 3.3 | 3.4 | 3.5 | V | | 6 |
| Internal LDO short-circuit current limit | IVCC-REG | 115 | | 170 | mA | | 6 |
| VDDA regulation voltage | VVDDA-REG | 4.75 | 5 | 5.25 | V | | 6 |
| VDDA UVLO rising | VVDDA-UVLO | 3 | 3.2 | 3.3 | V | VVCC rising, VVCCX = 0 V | 6 |
| VCCX rising threshold | VVCCX-ON | 4.1 | 4.3 | 4.4 | V | | 6 |
| Regulated FB voltage | VREF | 795 | 800 | 808 | mV | | 6 |
| 3.3-V output voltage setpoint, internal compensation | VOUT-3.3V-INT | 3.267 | 3.3 | 3.33 | V | RFB = 0 Ω, VIN = 3.8 V to 80 V, internal compensation | 6 |
| 3.3-V output voltage setpoint, external compensation | VOUT-3.3V-EXT | 3.267 | 3.3 | 3.33 | V | RFB = 0 Ω, VIN = 3.8 V to 80 V, external compensation | 7 |
| 5-V output voltage setpoint, internal compensation | VOUT-5V-INT | 4.95 | 5 | 5.05 | V | RFB = 24.9 kΩ, VIN = 5.5 V to 80 V, internal compensation | 7 |
| 5-V output voltage setpoint, external compensation | VOUT-5V-EXT | 4.95 | 5 | 5.05 | V | RFB = 24.9 kΩ, VIN = 5.5 V to 80 V, external compensation | 7 |
| 12-V output setpoint, internal compensation | VOUT-12V-INT | 11.88 | 12 | 12.12 | V | RFB = 48.7 kΩ, VIN = 24 V to 80 V, internal compensation | 7 |
| 12-V output setpoint, external compensation | VOUT-12V-EXT | 11.88 | 12 | 12.12 | V | RFB = 48.7 kΩ, VIN = 24 V to 80 V, external compensation | 7 |
| 5-V output select | RFB-OPT1 | 23 | 25 | 27 | kΩ | | 7 |
| 12-V output select | RFB-OPT2 | 47 | 50 | 53 | kΩ | | 7 |
| EA transconductance, external compensation | gm-EXTERNAL | 1020 | 1200 | | µS | FB to COMP | 7 |
| EA transconductance, internal compensation | gm-INTERNAL | 10 | 30 | | µS | EXTCOMP 10 kΩ to VDDA | 7 |
| Frequency sync range | FSYNCIN | 1.74 | | 2.7 | MHz | RRT = 9.52 kΩ, ±20% of the nominal oscillator frequency | 7 |
| Switching frequency 2 | FSW2 | 1.98 | 2.2 | 2.42 | MHz | VIN = 12 V, RRT = 9.52 kΩ to AGND | 7 |
| Power Good UV trip level | VPG-UV | 90 | 92 | 94 | % | Falling with respect to the regulated voltage | 7 |
| Power Good OV trip level | VPG-OV | 108 | 110 | 112 | % | Rising with respect to the regulation voltage | 7 |
| Internal fixed soft-start time | tSS-INT | 1.9 | 3 | 4.6 | ms | | 8 |
| Current limit threshold | VCS-TH | 49 | 60 | 73 | mV | Measured from ISNS+ to VOUT | 8 |
| CS amplifier gain | GCS | 9 | 10 | 10.8 | V/V | | 8 |
| Primary, no spread spectrum | RCONF-OPT1 | 28.7 | 29.4 | 31 | kΩ | | 8 |
| Primary, with spread spectrum | RCONF-OPT2 | 40.2 | 41.2 | 43.2 | kΩ | | 8 |
| Primary, interleaved, no spread spectrum | RCONF-OPT3 | 53.6 | 54.9 | 57.6 | kΩ | | 8 |
| Primary, interleaved, with spread spectrum | RCONF-OPT4 | 69.8 | 71.5 | 73.2 | kΩ | | 9 |
| Secondary | RCONF-OPT5 | 87 | 90.9 | 93.1 | kΩ | | 9 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | • Connect the MOSFETs (switch node) directly to the inductor terminal with short copper connections (without | 57 |
## CAD (Adom-generated)
- Symbol: `LM5148RGYR`
- Footprint: `Adom_Gen:TEXAS_INSTRUMENTS_LM5148_38543a`
- 3D model: generated to fit the land (STEP)
- 3D model files: `lm5148rgyr-etched.step` / `lm5148rgyr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5148rgyr.step` / `lm5148rgyr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [TEXAS INSTRUMENTS datasheet](https://www.ti.com/lit/ds/symlink/lm5148.pdf) (70 pp, sha256 `bdea4391ef5e5cfa`, retrieved 2026-11-16, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
[Datasheet PDF](docs/lm5148rgyr-datasheet.pdf)