main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs lm5143qrwgrq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers lm5143qrwgrq1: viewers · Ray
lm5143qrwgrq1-etched.fit.json lm5143qrwgrq1: one-pass backfill (re-etched, hero rebuilt in-pass (inputs changed)) · Ray
lm5143qrwgrq1-etched.glb lm5143qrwgrq1: one-pass backfill (re-etched, hero rebuilt in-pass (inputs changed)) · Ray
lm5143qrwgrq1-etched.step lm5143qrwgrq1: one-pass backfill (re-etched, hero rebuilt in-pass (inputs changed)) · Ray
lm5143qrwgrq1-hero.glb lm5143qrwgrq1: hero from the plain model · Ray
lm5143qrwgrq1-hero.overlay.json lm5143qrwgrq1: hero from the plain model · Ray
lm5143qrwgrq1.glb Publish 0.1.0 · Ray
lm5143qrwgrq1.kicad_mod Publish 0.1.0 · Ray
lm5143qrwgrq1.kicad_sym Publish 0.1.0 · Ray
lm5143qrwgrq1.lbr Publish 0.1.0 · Ray
lm5143qrwgrq1.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md lm5143qrwgrq1: specified limits as data (metadata.characteristics, 52 rows from the datasheet) · Ray

LM5143QRWGRQ1

Texas Instruments · DC-DC Converters · VQFN-40-EP(6x6)

LM5143QRWGRQ1 from Texas Instruments, in a VQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SS2 input Channel 2 soft-start programming pin; external capacitor and 20-μA current source set error amplifier ramp; pulling below 150 mV disables gate drivers.
2 COMP2 output Channel 2 error amplifier output for external compensation; high impedance in interleave or slave modes.
3 FB2 input Feedback input for 0.6 V regulation; connect to VDDA for 3.3 V or AGND for 5 V fixed output.
4 CS2 input Current sense amplifier input; connect via low-current Kelvin connection to inductor side of sense resistor.
5 VOUT2 input Output voltage sense node; connect to output side of sense resistor for current and voltage feedback.
6 VCCX power_in Optional external bias supply input; internal VCC regulator disabled when greater than 4.3 V; decouple with ceramic capacitor to PGND.
7 PG2 output Open-collector power-good output; goes low when VOUT2 outside 92%-110% regulation window with 25 μs filter delay.
8 HOL2 output Channel 2 high-side gate driver turnoff output; provides active pull-down for high-side MOSFET gate.
9 HO2 output Channel 2 high-side gate driver turnon output; sources up to 3.25 A peak current with 24 ns rise time.
10 SW2 passive Switching node for channel 2 buck converter; connects bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain.
11 HB2 power_out Bootstrap supply for channel 2 high-side gate driver; requires 0.1 μF ceramic capacitor to SW2.
12 LOL2 output Channel 2 low-side gate driver turnoff output; provides active pull-down for low-side MOSFET gate.
13 LO2 output Channel 2 low-side gate driver turnon output; sources up to 3.25 A peak current with 4 ns rise time.
14 PGND2 power_in Power ground for channel 2 gate driver; connect to system ground plane and output capacitor negative terminal.
15 VCC power_out Regulated 5 V bias supply output for gate drivers; 170 mA minimum sourcing capability; pins 15 and 16 must connect together on PCB.
16 VCC power_out Regulated 5 V bias supply output for gate drivers; 170 mA minimum sourcing capability; pins 15 and 16 must connect together on PCB.
17 PGND1 power_in Power ground for channel 1 gate driver; connect to system ground plane and output capacitor negative terminal.
18 LO1 output Channel 1 low-side gate driver turnon output; sources up to 3.25 A peak current with 4 ns rise time.
19 LOL1 output Channel 1 low-side gate driver turnoff output; provides active pull-down for low-side MOSFET gate.
20 HB1 power_out Bootstrap supply for channel 1 high-side gate driver; requires 0.1 μF ceramic capacitor to SW1.
21 SW1 passive Switching node for channel 1 buck converter; connects bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain.
22 HO1 output Channel 1 high-side gate driver turnon output; sources up to 3.25 A peak current with 24 ns rise time.
23 HOL1 output Channel 1 high-side gate driver turnoff output; provides active pull-down for high-side MOSFET gate.
24 PG1 output Open-collector power-good output; goes low when VOUT1 outside 92%-110% regulation window with 25 μs filter delay.
25 VIN power_in Primary power supply input for voltage regulators; operates 3.5 V to 65 V steady-state; absolute maximum 70 V.
26 VOUT1 input Output voltage sense node for channel 1; connect to output side of sense resistor for current and voltage feedback.
27 CS1 input Current sense amplifier input for channel 1; connect via low-current Kelvin connection to inductor side of sense resistor.
28 FB1 input Feedback input for 0.6 V regulation; connect to VDDA for 3.3 V or AGND for 5 V fixed output.
29 COMP1 output Channel 1 error amplifier output for external compensation; high impedance in slave mode.
30 SS1 input Channel 1 soft-start programming pin; external capacitor and 20-μA current source set error amplifier ramp; pulling below 150 mV disables gate drivers.
31 EN1 input Active-high enable input for output 1; voltage greater than 2 V enables, less than 0.4 V disables; maximum 70 V; must never float.
32 RES output Hiccup mode restart timer pin; external capacitor sets off-time before auto-restart after 512 consecutive current-limit cycles per channel.
33 DEMB input Diode emulation or synchronization input; low enables DCM, high enables FPWM, or external clock up to 2.5 MHz for synchronization.
34 MODE input Configuration pin for output mode and error amplifier gain; ground for 1200 µS or 10 kΩ to ground for 60 µS ultra-low IQ mode.
35 AGND power_in Analog ground connection; reference return for internal voltage reference and analog signal circuits.
36 VDDA power_out Internal 5 V analog bias regulator output; requires 470 nF ceramic decoupling capacitor to AGND.
37 RT input Oscillator frequency set pin; resistor to AGND determines frequency 100 kHz to 2.2 MHz per equation FSW = 22/(R in kΩ).
38 DITH input Spread spectrum dithering pin; capacitor to AGND charged by 20-μA source modulates frequency ±5%; connect to VDDA to disable.
39 SYNCOUT output Synchronization output; logic-level signal with rising edge 90° lagging HO2 for cascading multiple controllers.
40 EN2 input Active-high enable input for output 2; voltage greater than 2 V enables, less than 0.4 V disables; maximum 70 V; must never float.
41 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-40-EP(6x6)
Category Power Management (PMIC)
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC regulation voltage VVCC-REG 4.7 5 5.3 V VVIN = 12 V, IVCC = 100 mA, VVCCX = 0 V 9
VCC UVLO rising threshold VVCC-UVLO 3.2 3.3 3.4 V VVCC rising 9
VDDA regulation voltage VVDDA-REG 4.75 5 5.25 V 9
VDDA UVLO rising threshold VVDDA-UVLO 3.1 3.2 3.3 V VVCC rising, VVCCX = 0 V 9
VCCX(ON) rising threshold VVCCX-ON 4.1 4.3 4.4 V 9
Current limit threshold 1 (CS1 to VOUT1) VCS1 66 73 80 mV Measured from CS1 to VOUT1 9
Current limit threshold 2 (CS2 to VOUT2) VCS2 66 73 80 mV Measured from CS2 to VOUT2 9
CS amplifier gain GCS 11.4 12 12.6 V/V 9
PG1 UV trip level PG1UV 90 92 94 % Falling with respect to the regulation voltage 9
PG2 UV trip level PG2UV 90 92 94 % Falling with respect to the regulation voltage 9
PG1 OV trip level PG1OV 108 110 112 % Rising with respect to the regulation voltage 9
PG2 OV trip level PG2OV 108 110 112 % Rising with respect to the regulation voltage 9
3.3 V output voltage setpoint VOUT33 3.267 3.3 3.33 V VFB = 0 V, VIN = 3.5 V to 65 V 10
5 V output voltage setpoint VOUT50 4.95 5 5.05 V VFB = 5 V, VIN = 5.5 V to 65 V 10
Regulated feedback voltage VFB-REG 0.594 0.6 0.606 V TJ = –40°C to 125°C 10
External SYNC frequency range, % of nominal set by RRT FSYNCIN -20 20 % VIN = 8 V to 18 V, % of the nominal frequency set by RRT 11
Switching frequency 1 FSW1 200 220 242 kHz RRT = 100 kΩ 12
Soft-start current ISS 16 21 28 µA VMODE = 0 V 12
VIN to PGND (absolute maximum) -0.3 70 V 7
SW1, SW2 to PGND (absolute maximum) -0.3 70 V 7
SW1, SW2 to PGND (20-ns transient) -5 V 20-ns transient 7
HB1 to SW1, HB2 to SW2 (absolute maximum) -0.3 6.5 V 7
HB1 to SW1, HB2 to SW2 (20-ns transient) -5 V 20-ns transient 7
HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 (max VHB + 0.3 V, not numeric) -0.3 V 7
HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 (20-ns transient) -5 V 20-ns transient 7
LO1, LOL1, LO2, LOL2 to PGND (max VVCC + 0.3 V, not numeric) -0.3 V 7
LO1, LOL1, LO2, LOL2 to PGND (20-ns transient, max VVCC + 0.3 V) -1.5 V 20-ns transient 7
SS1, SS2, COMP1, COMP2, RES, RT, MODE, DITH to AGND (max VVDDA + 0.3 V, not numeric) -0.3 V 7
EN1, EN2 to PGND (absolute maximum) -0.3 70 V 7
VCC, VCCX, VDDA, PG1, PG2, DEMB, FB1, FB2 to AGND (absolute maximum) -0.3 6.5 V 7
VOUT1, VOUT2, CS1, CS2 (absolute maximum) -0.3 60 V 7
VOUT1 to CS1, VOUT2 to CS2 (absolute maximum) -0.3 0.3 V 7
PGND to AGND (absolute maximum) -0.3 0.3 V 7
Operating junction temperature, TJ (absolute maximum) TJ -40 150 °C 7
Storage temperature (absolute maximum) Tstg -40 150 °C 7
VIN to PGND (recommended operating) -0.3 65 V 8
SW1, SW2 to PGND (recommended operating) -0.3 65 V 8
HB1 to SW1, HB2 to SW2 (recommended operating) -0.3 5 5.25 V 8
HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 (recommended operating, max VHB + 0.3 V, not numeric) -0.3 V 8
LO1, LOL1, LO2, LOL2 to PGND (recommended operating) -0.3 5 5.25 V 8
FB1, FB2, SS1, SS2, COMP1, COMP2, RES, DEMB, RT, MODE, DITH to AGND (recommended operating) -0.3 5.25 V 8
EN1, EN2 to PGND (recommended operating) -0.3 65 V 8
VCC, VCCX, VDDA to PGND (recommended operating) -0.3 5 5.25 V 8
VOUT1, VOUT2, CS1, CS2 to PGND (recommended operating) -0.3 55 V 8
PGND to AGND (recommended operating) -0.3 0.3 V 8
Operating junction temperature (recommended operating) TJ -40 150 °C 8
Junction-to-ambient thermal resistance RΘJA 34.8 °C/W 8
Junction-to-case (top) thermal resistance RΘJC(top) 22.8 °C/W 8
Junction-to-board thermal resistance RΘJB 9.5 °C/W 8
Junction-to-case (bottom) thermal resistance RΘJC(bot) 1.3 °C/W 8
Junction-to-board characterization parameter ΨJB 9.4 °C/W 8
Junction-to-top characterization parameter ΨJT 0.3 °C/W 8

CAD (KiCad official)

  • Symbol: LM5143QRWGRQ1
  • Footprint: Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm
  • 3D model: VQFN-40-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: lm5143qrwgrq1-etched.step / lm5143qrwgrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5143qrwgrq1.step / lm5143qrwgrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (70 pp, sha256 7f505f2c1dac109f, retrieved 2026-09-26, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF