← Commit history

Initial commit: component/lm5143qrwgrq1

Ray ·0742b2e25a ·
2 files changed +436
README.mdadded+78
@@ -0,0 +1,78 @@+# LM5143QRWGRQ1++**Texas Instruments** · DC-DC Converters · VQFN-40-EP(6x6)++LM5143QRWGRQ1 from Texas Instruments, in a VQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SS2 | input | Channel 2 soft-start programming pin; external capacitor and 20-μA current source set error amplifier ramp; pulling below 150 mV disables gate drivers. |+| 2 | COMP2 | output | Channel 2 error amplifier output for external compensation; high impedance in interleave or slave modes. |+| 3 | FB2 | input | Feedback input for 0.6 V regulation; connect to VDDA for 3.3 V or AGND for 5 V fixed output. |+| 4 | CS2 | input | Current sense amplifier input; connect via low-current Kelvin connection to inductor side of sense resistor. |+| 5 | VOUT2 | input | Output voltage sense node; connect to output side of sense resistor for current and voltage feedback. |+| 6 | VCCX | power_in | Optional external bias supply input; internal VCC regulator disabled when greater than 4.3 V; decouple with ceramic capacitor to PGND. |+| 7 | PG2 | output | Open-collector power-good output; goes low when VOUT2 outside 92%-110% regulation window with 25 μs filter delay. |+| 8 | HOL2 | output | Channel 2 high-side gate driver turnoff output; provides active pull-down for high-side MOSFET gate. |+| 9 | HO2 | output | Channel 2 high-side gate driver turnon output; sources up to 3.25 A peak current with 24 ns rise time. |+| 10 | SW2 | passive | Switching node for channel 2 buck converter; connects bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain. |+| 11 | HB2 | power_out | Bootstrap supply for channel 2 high-side gate driver; requires 0.1 μF ceramic capacitor to SW2. |+| 12 | LOL2 | output | Channel 2 low-side gate driver turnoff output; provides active pull-down for low-side MOSFET gate. |+| 13 | LO2 | output | Channel 2 low-side gate driver turnon output; sources up to 3.25 A peak current with 4 ns rise time. |+| 14 | PGND2 | power_in | Power ground for channel 2 gate driver; connect to system ground plane and output capacitor negative terminal. |+| 15 | VCC | power_out | Regulated 5 V bias supply output for gate drivers; 170 mA minimum sourcing capability; pins 15 and 16 must connect together on PCB. |+| 16 | VCC | power_out | Regulated 5 V bias supply output for gate drivers; 170 mA minimum sourcing capability; pins 15 and 16 must connect together on PCB. |+| 17 | PGND1 | power_in | Power ground for channel 1 gate driver; connect to system ground plane and output capacitor negative terminal. |+| 18 | LO1 | output | Channel 1 low-side gate driver turnon output; sources up to 3.25 A peak current with 4 ns rise time. |+| 19 | LOL1 | output | Channel 1 low-side gate driver turnoff output; provides active pull-down for low-side MOSFET gate. |+| 20 | HB1 | power_out | Bootstrap supply for channel 1 high-side gate driver; requires 0.1 μF ceramic capacitor to SW1. |+| 21 | SW1 | passive | Switching node for channel 1 buck converter; connects bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain. |+| 22 | HO1 | output | Channel 1 high-side gate driver turnon output; sources up to 3.25 A peak current with 24 ns rise time. |+| 23 | HOL1 | output | Channel 1 high-side gate driver turnoff output; provides active pull-down for high-side MOSFET gate. |+| 24 | PG1 | output | Open-collector power-good output; goes low when VOUT1 outside 92%-110% regulation window with 25 μs filter delay. |+| 25 | VIN | power_in | Primary power supply input for voltage regulators; operates 3.5 V to 65 V steady-state; absolute maximum 70 V. |+| 26 | VOUT1 | input | Output voltage sense node for channel 1; connect to output side of sense resistor for current and voltage feedback. |+| 27 | CS1 | input | Current sense amplifier input for channel 1; connect via low-current Kelvin connection to inductor side of sense resistor. |+| 28 | FB1 | input | Feedback input for 0.6 V regulation; connect to VDDA for 3.3 V or AGND for 5 V fixed output. |+| 29 | COMP1 | output | Channel 1 error amplifier output for external compensation; high impedance in slave mode. |+| 30 | SS1 | input | Channel 1 soft-start programming pin; external capacitor and 20-μA current source set error amplifier ramp; pulling below 150 mV disables gate drivers. |+| 31 | EN1 | input | Active-high enable input for output 1; voltage greater than 2 V enables, less than 0.4 V disables; maximum 70 V; must never float. |+| 32 | RES | output | Hiccup mode restart timer pin; external capacitor sets off-time before auto-restart after 512 consecutive current-limit cycles per channel. |+| 33 | DEMB | input | Diode emulation or synchronization input; low enables DCM, high enables FPWM, or external clock up to 2.5 MHz for synchronization. |+| 34 | MODE | input | Configuration pin for output mode and error amplifier gain; ground for 1200 µS or 10 kΩ to ground for 60 µS ultra-low IQ mode. |+| 35 | AGND | power_in | Analog ground connection; reference return for internal voltage reference and analog signal circuits. |+| 36 | VDDA | power_out | Internal 5 V analog bias regulator output; requires 470 nF ceramic decoupling capacitor to AGND. |+| 37 | RT | input | Oscillator frequency set pin; resistor to AGND determines frequency 100 kHz to 2.2 MHz per equation FSW = 22/(R in kΩ). |+| 38 | DITH | input | Spread spectrum dithering pin; capacitor to AGND charged by 20-μA source modulates frequency ±5%; connect to VDDA to disable. |+| 39 | SYNCOUT | output | Synchronization output; logic-level signal with rising edge 90° lagging HO2 for cascading multiple controllers. |+| 40 | EN2 | input | Active-high enable input for output 2; voltage greater than 2 V enables, less than 0.4 V disables; maximum 70 V; must never float. |+| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-40-EP(6x6) |+| Category | Power Management (PMIC) |+| Pins | 41 |++## CAD (KiCad official)++- Symbol: `LM5143QRWGRQ1`+- Footprint: `Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm`+- 3D model: VQFN-40-EP(6x6) (KiCad packages3D, STEP)+- 3D model files: `lm5143qrwgrq1-etched.step` / `lm5143qrwgrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5143qrwgrq1.step` / `lm5143qrwgrq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5143-q1) (70 pp, sha256 `7f505f2c1dac109f`, retrieved 2026-09-26, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm5143qrwgrq1-datasheet.pdf)
page.jsonadded+358
@@ -0,0 +1,358 @@+{+  "slug": "lm5143qrwgrq1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, VQFN-40-EP(6x6). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "lm5143qrwgrq1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm5143qrwgrq1.kicad_sym",+    "lm5143qrwgrq1.kicad_mod",+    "lm5143qrwgrq1.glb",+    "lm5143qrwgrq1.step",+    "lm5143qrwgrq1.lbr",+    "docs/hero.png",+    "docs/lm5143qrwgrq1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM5143QRWGRQ1",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-40-EP(6x6)",+    "pin_count": 41,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm5143-q1",+    "parts": {+      "symbol": "lm5143qrwgrq1.kicad_sym",+      "footprint": "lm5143qrwgrq1.kicad_mod",+      "model_3d": "lm5143qrwgrq1-etched.glb",+      "model_3d_plain": "lm5143qrwgrq1.glb",+      "model_3d_step": "lm5143qrwgrq1-etched.step",+      "model_3d_step_plain": "lm5143qrwgrq1.step",+      "lbr": "lm5143qrwgrq1.lbr"+    },+    "distributor_links": {+      "lcsc": "C1849541",+      "digikey": "296-LM5143QRWGRQ1TR-ND",+      "mouser": "595-LM5143QRWGRQ1"+    },+    "distributor_check": {+      "checked_at": "2026-09-26T18:54:51Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-LM5143QRWGRQ1TR-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-LM5143QRWGRQ1",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "SS2",+        "type": "input",+        "description": "Channel 2 soft-start programming pin; external capacitor and 20-μA current source set error amplifier ramp; pulling below 150 mV disables gate drivers."+      },+      {+        "number": "2",+        "name": "COMP2",+        "type": "output",+        "description": "Channel 2 error amplifier output for external compensation; high impedance in interleave or slave modes."+      },+      {+        "number": "3",+        "name": "FB2",+        "type": "input",+        "description": "Feedback input for 0.6 V regulation; connect to VDDA for 3.3 V or AGND for 5 V fixed output."+      },+      {+        "number": "4",+        "name": "CS2",+        "type": "input",+        "description": "Current sense amplifier input; connect via low-current Kelvin connection to inductor side of sense resistor."+      },+      {+        "number": "5",+        "name": "VOUT2",+        "type": "input",+        "description": "Output voltage sense node; connect to output side of sense resistor for current and voltage feedback."+      },+      {+        "number": "6",+        "name": "VCCX",+        "type": "power_in",+        "description": "Optional external bias supply input; internal VCC regulator disabled when greater than 4.3 V; decouple with ceramic capacitor to PGND."+      },+      {+        "number": "7",+        "name": "PG2",+        "type": "output",+        "description": "Open-collector power-good output; goes low when VOUT2 outside 92%-110% regulation window with 25 μs filter delay."+      },+      {+        "number": "8",+        "name": "HOL2",+        "type": "output",+        "description": "Channel 2 high-side gate driver turnoff output; provides active pull-down for high-side MOSFET gate."+      },+      {+        "number": "9",+        "name": "HO2",+        "type": "output",+        "description": "Channel 2 high-side gate driver turnon output; sources up to 3.25 A peak current with 24 ns rise time."+      },+      {+        "number": "10",+        "name": "SW2",+        "type": "passive",+        "description": "Switching node for channel 2 buck converter; connects bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain."+      },+      {+        "number": "11",+        "name": "HB2",+        "type": "power_out",+        "description": "Bootstrap supply for channel 2 high-side gate driver; requires 0.1 μF ceramic capacitor to SW2."+      },+      {+        "number": "12",+        "name": "LOL2",+        "type": "output",+        "description": "Channel 2 low-side gate driver turnoff output; provides active pull-down for low-side MOSFET gate."+      },+      {+        "number": "13",+        "name": "LO2",+        "type": "output",+        "description": "Channel 2 low-side gate driver turnon output; sources up to 3.25 A peak current with 4 ns rise time."+      },+      {+        "number": "14",+        "name": "PGND2",+        "type": "power_in",+        "description": "Power ground for channel 2 gate driver; connect to system ground plane and output capacitor negative terminal."+      },+      {+        "number": "15",+        "name": "VCC",+        "type": "power_out",+        "description": "Regulated 5 V bias supply output for gate drivers; 170 mA minimum sourcing capability; pins 15 and 16 must connect together on PCB."+      },+      {+        "number": "16",+        "name": "VCC",+        "type": "power_out",+        "description": "Regulated 5 V bias supply output for gate drivers; 170 mA minimum sourcing capability; pins 15 and 16 must connect together on PCB."+      },+      {+        "number": "17",+        "name": "PGND1",+        "type": "power_in",+        "description": "Power ground for channel 1 gate driver; connect to system ground plane and output capacitor negative terminal."+      },+      {+        "number": "18",+        "name": "LO1",+        "type": "output",+        "description": "Channel 1 low-side gate driver turnon output; sources up to 3.25 A peak current with 4 ns rise time."+      },+      {+        "number": "19",+        "name": "LOL1",+        "type": "output",+        "description": "Channel 1 low-side gate driver turnoff output; provides active pull-down for low-side MOSFET gate."+      },+      {+        "number": "20",+        "name": "HB1",+        "type": "power_out",+        "description": "Bootstrap supply for channel 1 high-side gate driver; requires 0.1 μF ceramic capacitor to SW1."+      },+      {+        "number": "21",+        "name": "SW1",+        "type": "passive",+        "description": "Switching node for channel 1 buck converter; connects bootstrap capacitor, high-side MOSFET source, and low-side MOSFET drain."+      },+      {+        "number": "22",+        "name": "HO1",+        "type": "output",+        "description": "Channel 1 high-side gate driver turnon output; sources up to 3.25 A peak current with 24 ns rise time."+      },+      {+        "number": "23",+        "name": "HOL1",+        "type": "output",+        "description": "Channel 1 high-side gate driver turnoff output; provides active pull-down for high-side MOSFET gate."+      },+      {+        "number": "24",+        "name": "PG1",+        "type": "output",+        "description": "Open-collector power-good output; goes low when VOUT1 outside 92%-110% regulation window with 25 μs filter delay."+      },+      {+        "number": "25",+        "name": "VIN",+        "type": "power_in",+        "description": "Primary power supply input for voltage regulators; operates 3.5 V to 65 V steady-state; absolute maximum 70 V."+      },+      {+        "number": "26",+        "name": "VOUT1",+        "type": "input",+        "description": "Output voltage sense node for channel 1; connect to output side of sense resistor for current and voltage feedback."+      },+      {+        "number": "27",+        "name": "CS1",+        "type": "input",+        "description": "Current sense amplifier input for channel 1; connect via low-current Kelvin connection to inductor side of sense resistor."+      },+      {+        "number": "28",+        "name": "FB1",+        "type": "input",+        "description": "Feedback input for 0.6 V regulation; connect to VDDA for 3.3 V or AGND for 5 V fixed output."+      },+      {+        "number": "29",+        "name": "COMP1",+        "type": "output",+        "description": "Channel 1 error amplifier output for external compensation; high impedance in slave mode."+      },+      {+        "number": "30",+        "name": "SS1",+        "type": "input",+        "description": "Channel 1 soft-start programming pin; external capacitor and 20-μA current source set error amplifier ramp; pulling below 150 mV disables gate drivers."+      },+      {+        "number": "31",+        "name": "EN1",+        "type": "input",+        "description": "Active-high enable input for output 1; voltage greater than 2 V enables, less than 0.4 V disables; maximum 70 V; must never float."+      },+      {+        "number": "32",+        "name": "RES",+        "type": "output",+        "description": "Hiccup mode restart timer pin; external capacitor sets off-time before auto-restart after 512 consecutive current-limit cycles per channel."+      },+      {+        "number": "33",+        "name": "DEMB",+        "type": "input",+        "description": "Diode emulation or synchronization input; low enables DCM, high enables FPWM, or external clock up to 2.5 MHz for synchronization."+      },+      {+        "number": "34",+        "name": "MODE",+        "type": "input",+        "description": "Configuration pin for output mode and error amplifier gain; ground for 1200 µS or 10 kΩ to ground for 60 µS ultra-low IQ mode."+      },+      {+        "number": "35",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground connection; reference return for internal voltage reference and analog signal circuits."+      },+      {+        "number": "36",+        "name": "VDDA",+        "type": "power_out",+        "description": "Internal 5 V analog bias regulator output; requires 470 nF ceramic decoupling capacitor to AGND."+      },+      {+        "number": "37",+        "name": "RT",+        "type": "input",+        "description": "Oscillator frequency set pin; resistor to AGND determines frequency 100 kHz to 2.2 MHz per equation FSW = 22/(R in kΩ)."+      },+      {+        "number": "38",+        "name": "DITH",+        "type": "input",+        "description": "Spread spectrum dithering pin; capacitor to AGND charged by 20-μA source modulates frequency ±5%; connect to VDDA to disable."+      },+      {+        "number": "39",+        "name": "SYNCOUT",+        "type": "output",+        "description": "Synchronization output; logic-level signal with rising edge 90° lagging HO2 for cascading multiple controllers."+      },+      {+        "number": "40",+        "name": "EN2",+        "type": "input",+        "description": "Active-high enable input for output 2; voltage greater than 2 V enables, less than 0.4 V disables; maximum 70 V; must never float."+      },+      {+        "number": "41",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: SW1 and SW2 classified as passive switching nodes rather than power_in/power_out; these are high-cur; HB1 and HB2 classified as power_out (bootstrap gate driver supplies) though they function as passive; VCCX classified as power_in though it can source current to internal VCC when enabled; more precisel",+          "exposed pad 41 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 70,+        "cost_usd": 0.7503,+        "at": "2026-09-26T18:54:32"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm5143-q1",+        "pages": 70,+        "sha256": "7f505f2c1dac109f",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 41,+        "described": 41,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file