main
History Download
Ray Initial commit: component/lm5116mh 837a0d3

LM5116MH

Texas Instruments · Global Sourcing Parts · HTSSOP-20-EP

LM5116MH from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Chip supply voltage, input voltage monitor, and input to the VCC regulator; operating range 6 V to 100 V.
2 UVLO input Undervoltage lockout input; regulator enters standby mode when below 1.215 V and operational when above 1.215 V with 0.1 V hysteresis.
3 RT/SYNC input Oscillator frequency setting pin; internal resistor to AGND sets switching frequency from 50 kHz to 1 MHz or accepts external clock synchronization via AC-coupled positive edge.
4 EN input Enable control input; regulator enters low-power shutdown below 0.5 V drawing less than 10 µA, normal operation above 3.3 V.
5 RAMP input Ramp generator capacitor connection; external capacitor between this pin and AGND sets ramp slope for emulated current mode control.
6 AGND power_in Analog ground; must be connected to PGND through the exposed pad ground connection.
7 SS input Soft-start capacitor connection; 10-µA internal current source sets soft-start time constant with output reference voltage 1.215 V.
8 FB input Feedback signal input; connected to inverting input of error amplifier with regulation threshold at 1.215 V, operating range −0.3 V to 7 V.
9 COMP output Error amplifier output; loop compensation network (RCOMP, CCOMP) must be connected between this pin and FB pin.
10 VOUT input Output voltage monitor input; connect directly to regulated output for feedback with operating range −0.3 V to 100 V.
11 DEMB input Diode emulation control input monitoring low-side MOSFET source voltage; operation controlled by external resistor with operating range −0.3 V to VCC.
12 CS input Current sense amplifier input; connect to top of current sense resistor or drain of low-side MOSFET with operating range −3.0 V to 100 V.
13 CSG power_in Current sense amplifier reference; connect to bottom of sense resistor or source of low-side MOSFET with operating range −1 V to 1 V.
14 PGND power_in Power ground; must be connected to AGND through the exposed pad ground connection.
15 LO output Low-side MOSFET gate driver output; provides peak sink current 3.5 A and peak source current 1.8 A for gate drive.
16 VCC power_in Internal bias supply output regulated to 7.4 V; locally decouple with low ESR capacitor with minimum source current limit 15 mA.
17 VCCX power_in Optional external VCC supply input; when above 4.5 V the internal VCC regulator disables, must be connected to ground if unused.
18 HB power_in Bootstrap supply for high-side gate driver; charged through bootstrap diode from VCC with HB-to-SW operating range 4.75 V to 15 V.
19 HO output High-side MOSFET gate driver output; provides peak sink current 2.2 A and peak source current 1 A referenced to SW node.
20 SW output Switching node output; connect to bootstrap capacitor negative and high-side MOSFET source with operating range −3.0 V to 100 V.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20-EP
Category Global Sourcing Parts
Pins 21

CAD (KiCad official)

  • Symbol: LM5116MH
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: lm5116mh-etched.step / lm5116mh-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5116mh.step / lm5116mh.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (46 pp, sha256 f2eb85eece02d5e7, retrieved 2026-10-01, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF