main
Ray
Publish 0.1.0
beaf6f7
LM5088QMH-1
Texas Instruments · DC-DC Controllers · HTSSOP-16-EP
LM5088QMH-1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply voltage for the IC, with an operating range of 4.5 V to 75 V and a 76 V absolute maximum on VIN to GND. |
| 2 | EN | input | Enable input: below 0.4 V the regulator is in low-power shutdown, 0.4 V to 1.2 V selects standby, and above 1.2 V the controller is operational; the pin may not exceed 14 V. |
| 3 | SS | passive | Soft-start pin charged by an internal 11-µA source into an external capacitor; it is held low in standby, VCC UVLO and thermal shutdown, and can track an external voltage below 1.2 V. |
| 4 | RAMP | output | An external capacitor from RAMP to GND, recommended 100 pF to 2000 pF, sets the emulated current-mode ramp slope. |
| 5 | RT/SYNC | input | Oscillator frequency-set pin with a single resistor to GND (recommended 50 kHz to 1 MHz); it also accepts an AC-coupled sync pulse above the programmed frequency, and the RT resistor is still required when syncing. |
| 6 | GND | power_in | Ground return for the controller. |
| 7 | COMP | output | Output of the internal error amplifier; the loop compensation network connects between COMP and FB. |
| 8 | FB | input | Feedback input to the inverting input of the error amplifier, with a regulation threshold of 1.205 V. |
| 9 | OUT | input | Output voltage connection, to be connected directly to the regulated output voltage. |
| 10 | DITH | passive | Frequency dithering pin (LM5088-1 only): a capacitor to GND is charged and discharged by 27-µA sources to modulate the oscillator between -5% and +5% of nominal, and grounding the pin disables dithering. |
| 11 | CSG | passive | Current sense ground, the low-side reference for the current sense resistor, which must be Kelvin connected. |
| 12 | CS | input | Current sense input that measures the re-circulating diode current through the sense resistor to provide the DC offset of the emulated ramp. |
| 13 | SW | passive | Switching node, connected to the source terminal of the external buck MOSFET. |
| 14 | HG | output | High-side gate drive output, connected to the gate of the external N-channel MOSFET. |
| 15 | BOOT | passive | Bootstrap input; the bootstrap capacitor between BOOT and SW is charged from VCC through an internal diode during the buck off-time. |
| 16 | VCC | power_out | Bias regulator output that tracks VIN up to 7.8 V typical, requires a 0.1-µF to 10-µF ceramic decoupling capacitor, and may be overdriven by an external 8.3 V to 13 V supply. |
| 17 | EP | passive | Exposed thermal pad, electrically isolated from the leads, which must be soldered to the ground plane to reduce thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN operating current | IBIAS | 5.5 | mA | VFB = 1.3 V; TJ = -40°C to +125°C | 6 | ||
| VIN operating current | IBIAS | 3.8 | mA | VFB = 1.3 V; TJ = 25°C | 6 | ||
| VIN standby current | ISTANDBY | 3.6 | mA | VEN = 1 V; TJ = -40°C to +125°C | 6 | ||
| VIN standby current | ISTANDBY | 2.9 | mA | VEN = 1 V; TJ = 25°C | 6 | ||
| VIN shutdown current | ISHUTDOWN | 26 | µA | VEN = 0 V; TJ = -40°C to +125°C | 6 | ||
| VIN shutdown current | ISHUTDOWN | 15 | µA | VEN = 0 V; TJ = 25°C | 6 | ||
| VCC regulation | VVCC(Reg) | 7.4 | 8.2 | V | VVCC = open; TJ = -40°C to +125°C | 6 | |
| VCC regulation | VVCC(Reg) | 4.3 | V | VVIN = 4.5 V, VVCC = open | 6 | ||
| VCC sourcing current limit | 30 | mA | VVCC = 0 | 6 | |||
| VCC undervoltage lockout threshold | VVCC(UV) | 3.7 | 4 | V | Positive going VVCC | 6 | |
| EN shutdown threshold | 320 | 480 | mV | VEN rising | 6 | ||
| EN standby threshold | 1.1 | 1.3 | V | VEN rising | 6 | ||
| SS pullup current source | 8 | 13 | µA | VSS = 0 V | 6 | ||
| FB reference voltage | VREF | 1.187 | 1.223 | V | FB = COMP; measured at FB pin | 6 | |
| FB input bias current | 100 | nA | VFB = 1.2 V; TJ = -40°C to +125°C | 6 | |||
| FB input bias current | 18 | nA | VFB = 1.2 V; TJ = 25°C | 6 | |||
| Forced HG off time | tHG(OFF) | 185 | 365 | ns | 6 | ||
| SYNC pulse width | 15 | 150 | ns | 7 | |||
| Cycle-by-cycle sense voltage threshold | VCS(TH) | 112 | 136 | mV | VRAMP = 0 V | 7 | |
| RES threshold upper (rising) | Vresup | 1.1 | 1.3 | V | VCS = 0.125 | 7 | |
| RES threshold lower (falling) | Vresdown | 0.1 | 0.3 | V | 7 | ||
| Charge source current | Icharge | 40 | 65 | µA | VCS ≥ 0.125 | 7 | |
| Discharge sink current | Idischarge | 20 | 34 | µA | VCS < 0.125 | 7 | |
| Discharge sink current (post fault) | Irampdown | 0.8 | 1.6 | µA | 7 | ||
| RAMP current 1 | IRAMP1 | 235 | 345 | µA | VVIN = 60 V, VOUT = 10 V | 7 | |
| RAMP current 2 | IRAMP2 | 18 | 30 | µA | VVIN = 10 V, VOUT = 10 V | 7 | |
| HG low-state output voltage | VOLH | 215 | mV | IHG = 100 mA; TJ = -40°C to +125°C | 7 | ||
| HG low-state output voltage | VOLH | 115 | mV | IHG = 100 mA; TJ = 25°C | 7 | ||
| VIN, VOUT to GND | 76 | V | 5 | ||||
| BOOT to GND | 90 | V | 5 | ||||
| SW to GND | -2 | 76 | V | 5 | |||
| VCC to GND | -0.3 | 16 | V | 5 | |||
| HG to SW | -0.3 | V | Max = BOOT + 0.3 V | 5 | |||
| EN to GND | 14 | V | 5 | ||||
| BOOT to SW | -0.3 | 16 | V | 5 | |||
| CS, CSG to GND | -0.3 | 0.3 | V | 5 | |||
| All other inputs to GND | -0.3 | 7 | V | 5 | |||
| Junction temperature | 150 | °C | 5 | ||||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Electrostatic discharge, human body model | V(ESD) | -2000 | 2000 | V | HBM, per AEC Q100-002 | 5 | |
| Electrostatic discharge, charged device model | V(ESD) | -750 | 750 | V | CDM, per AEC Q100-011, all pins | 5 | |
| VIN voltage | 4.5 | 75 | V | 5 | |||
| VCC voltage (externally supplied) | 8.3 | 13 | V | 5 | |||
| Operation junction temperature | -40 | 125 | °C | 5 | |||
| Junction-to-ambient thermal resistance (RθJA) | RθJA | 40 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance (RθJC(bot)) | RθJC(bot) | 6 | °C/W | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | power ground connections (CSS, RT, and CRAMP) directly to the regulator GND pin. Connect the GND pin and PGND pins together through to top-side copper area covering the entire underside of the device. | 34 |
CAD (KiCad official)
- Symbol:
LM5088QMH-1 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm5088qmh-1-etched.step/lm5088qmh-1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5088qmh-1.step/lm5088qmh-1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (45 pp, sha256
471a76480f35dc1d, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM5088QMH-1
**Texas Instruments** · DC-DC Controllers · HTSSOP-16-EP
LM5088QMH-1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply voltage for the IC, with an operating range of 4.5 V to 75 V and a 76 V absolute maximum on VIN to GND. |
| 2 | EN | input | Enable input: below 0.4 V the regulator is in low-power shutdown, 0.4 V to 1.2 V selects standby, and above 1.2 V the controller is operational; the pin may not exceed 14 V. |
| 3 | SS | passive | Soft-start pin charged by an internal 11-µA source into an external capacitor; it is held low in standby, VCC UVLO and thermal shutdown, and can track an external voltage below 1.2 V. |
| 4 | RAMP | output | An external capacitor from RAMP to GND, recommended 100 pF to 2000 pF, sets the emulated current-mode ramp slope. |
| 5 | RT/SYNC | input | Oscillator frequency-set pin with a single resistor to GND (recommended 50 kHz to 1 MHz); it also accepts an AC-coupled sync pulse above the programmed frequency, and the RT resistor is still required when syncing. |
| 6 | GND | power_in | Ground return for the controller. |
| 7 | COMP | output | Output of the internal error amplifier; the loop compensation network connects between COMP and FB. |
| 8 | FB | input | Feedback input to the inverting input of the error amplifier, with a regulation threshold of 1.205 V. |
| 9 | OUT | input | Output voltage connection, to be connected directly to the regulated output voltage. |
| 10 | DITH | passive | Frequency dithering pin (LM5088-1 only): a capacitor to GND is charged and discharged by 27-µA sources to modulate the oscillator between -5% and +5% of nominal, and grounding the pin disables dithering. |
| 11 | CSG | passive | Current sense ground, the low-side reference for the current sense resistor, which must be Kelvin connected. |
| 12 | CS | input | Current sense input that measures the re-circulating diode current through the sense resistor to provide the DC offset of the emulated ramp. |
| 13 | SW | passive | Switching node, connected to the source terminal of the external buck MOSFET. |
| 14 | HG | output | High-side gate drive output, connected to the gate of the external N-channel MOSFET. |
| 15 | BOOT | passive | Bootstrap input; the bootstrap capacitor between BOOT and SW is charged from VCC through an internal diode during the buck off-time. |
| 16 | VCC | power_out | Bias regulator output that tracks VIN up to 7.8 V typical, requires a 0.1-µF to 10-µF ceramic decoupling capacitor, and may be overdriven by an external 8.3 V to 13 V supply. |
| 17 | EP | passive | Exposed thermal pad, electrically isolated from the leads, which must be soldered to the ground plane to reduce thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN operating current | IBIAS | | | 5.5 | mA | VFB = 1.3 V; TJ = -40°C to +125°C | 6 |
| VIN operating current | IBIAS | | | 3.8 | mA | VFB = 1.3 V; TJ = 25°C | 6 |
| VIN standby current | ISTANDBY | | | 3.6 | mA | VEN = 1 V; TJ = -40°C to +125°C | 6 |
| VIN standby current | ISTANDBY | | | 2.9 | mA | VEN = 1 V; TJ = 25°C | 6 |
| VIN shutdown current | ISHUTDOWN | | | 26 | µA | VEN = 0 V; TJ = -40°C to +125°C | 6 |
| VIN shutdown current | ISHUTDOWN | | | 15 | µA | VEN = 0 V; TJ = 25°C | 6 |
| VCC regulation | VVCC(Reg) | 7.4 | | 8.2 | V | VVCC = open; TJ = -40°C to +125°C | 6 |
| VCC regulation | VVCC(Reg) | 4.3 | | | V | VVIN = 4.5 V, VVCC = open | 6 |
| VCC sourcing current limit | | 30 | | | mA | VVCC = 0 | 6 |
| VCC undervoltage lockout threshold | VVCC(UV) | 3.7 | | 4 | V | Positive going VVCC | 6 |
| EN shutdown threshold | | 320 | | 480 | mV | VEN rising | 6 |
| EN standby threshold | | 1.1 | | 1.3 | V | VEN rising | 6 |
| SS pullup current source | | 8 | | 13 | µA | VSS = 0 V | 6 |
| FB reference voltage | VREF | 1.187 | | 1.223 | V | FB = COMP; measured at FB pin | 6 |
| FB input bias current | | | | 100 | nA | VFB = 1.2 V; TJ = -40°C to +125°C | 6 |
| FB input bias current | | | | 18 | nA | VFB = 1.2 V; TJ = 25°C | 6 |
| Forced HG off time | tHG(OFF) | 185 | | 365 | ns | | 6 |
| SYNC pulse width | | 15 | | 150 | ns | | 7 |
| Cycle-by-cycle sense voltage threshold | VCS(TH) | 112 | | 136 | mV | VRAMP = 0 V | 7 |
| RES threshold upper (rising) | Vresup | 1.1 | | 1.3 | V | VCS = 0.125 | 7 |
| RES threshold lower (falling) | Vresdown | 0.1 | | 0.3 | V | | 7 |
| Charge source current | Icharge | 40 | | 65 | µA | VCS ≥ 0.125 | 7 |
| Discharge sink current | Idischarge | 20 | | 34 | µA | VCS < 0.125 | 7 |
| Discharge sink current (post fault) | Irampdown | 0.8 | | 1.6 | µA | | 7 |
| RAMP current 1 | IRAMP1 | 235 | | 345 | µA | VVIN = 60 V, VOUT = 10 V | 7 |
| RAMP current 2 | IRAMP2 | 18 | | 30 | µA | VVIN = 10 V, VOUT = 10 V | 7 |
| HG low-state output voltage | VOLH | | | 215 | mV | IHG = 100 mA; TJ = -40°C to +125°C | 7 |
| HG low-state output voltage | VOLH | | | 115 | mV | IHG = 100 mA; TJ = 25°C | 7 |
| VIN, VOUT to GND | | | | 76 | V | | 5 |
| BOOT to GND | | | | 90 | V | | 5 |
| SW to GND | | -2 | | 76 | V | | 5 |
| VCC to GND | | -0.3 | | 16 | V | | 5 |
| HG to SW | | -0.3 | | | V | Max = BOOT + 0.3 V | 5 |
| EN to GND | | | | 14 | V | | 5 |
| BOOT to SW | | -0.3 | | 16 | V | | 5 |
| CS, CSG to GND | | -0.3 | | 0.3 | V | | 5 |
| All other inputs to GND | | -0.3 | | 7 | V | | 5 |
| Junction temperature | | | | 150 | °C | | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| Electrostatic discharge, human body model | V(ESD) | -2000 | | 2000 | V | HBM, per AEC Q100-002 | 5 |
| Electrostatic discharge, charged device model | V(ESD) | -750 | | 750 | V | CDM, per AEC Q100-011, all pins | 5 |
| VIN voltage | | 4.5 | | 75 | V | | 5 |
| VCC voltage (externally supplied) | | 8.3 | | 13 | V | | 5 |
| Operation junction temperature | | -40 | | 125 | °C | | 5 |
| Junction-to-ambient thermal resistance (RθJA) | RθJA | | 40 | | °C/W | | 6 |
| Junction-to-case (bottom) thermal resistance (RθJC(bot)) | RθJC(bot) | | 6 | | °C/W | | 6 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | power ground connections (CSS, RT, and CRAMP) directly to the regulator GND pin. Connect the GND pin and PGND pins together through to top-side copper area covering the entire underside of the device. | 34 |
## CAD (KiCad official)
- Symbol: `LM5088QMH-1`
- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`
- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `lm5088qmh-1-etched.step` / `lm5088qmh-1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5088qmh-1.step` / `lm5088qmh-1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm5088.pdf) (45 pp, sha256 `471a76480f35dc1d`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm5088qmh-1-datasheet.pdf)