Generated by kicad-footprint-generator · KiCad file format 20260206
LM5069MM-2
Texas Instruments · Monitors & Reset Circuits · VSSOP-10-0.5mm
LM5069MM-2 from Texas Instruments, in a VSSOP-10-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SENSE | input | Current sense input measuring the voltage across the sense resistor RS from VIN; if that voltage reaches 55 mV the load current is limited and the fault timer activates. |
| 2 | VIN | power_in | Positive supply input that needs a small ceramic bypass capacitor close to the pin to suppress transients when the load current is switched off. |
| 3 | UVLO | input | Undervoltage lockout input where an external divider sets the turnon threshold, an internal 21-µA source provides hysteresis, the enable threshold is 2.5 V, and it can also be used for remote shutdown. |
| 4 | OVLO | input | Overvoltage lockout input where an external divider sets the turnoff threshold, an internal 21-µA source provides hysteresis, and the disable threshold is 2.5 V. |
| 5 | GND | power_in | Circuit ground. |
| 6 | TIMER | bidirectional | Timing capacitor pin that sets the insertion time delay and fault timeout period and also sets the restart timing of the LM5069-2. |
| 7 | PWR | input | Power limit set pin where an external resistor, together with RS, sets the maximum power dissipation allowed in the external series pass MOSFET. |
| 8 | PGD | output | Open drain Power Good output that goes active high when the external MOSFET VDS decreases below 1.25 V and switches low when VDS increases above 2.5 V. |
| 9 | OUT | input | Output feedback connected to the output rail (external MOSFET source), used to determine MOSFET VDS for power limiting and to control the PGD indicator. |
| 10 | GATE | output | Gate drive output for the external MOSFET gate, typically 12 V above the OUT pin when enabled. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-10-0.5mm |
| Category | Power Management ICs |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | -0.3 | 100 | V | 4 | |||
| SENSE, OUT, and PGD to GND | -0.3 | 100 | V | 4 | |||
| GATE to GND | -0.3 | 100 | V | 4 | |||
| OUT to GND (1 ms transient) | -1 | 100 | V | 4 | |||
| UVLO to GND | -0.3 | 100 | V | 4 | |||
| OVLO to GND | -0.3 | 7 | V | 4 | |||
| VIN to SENSE | -0.3 | 0.3 | V | 4 | |||
| Maximum junction temperature | TJMAX | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| VIN supply voltage | VIN | 9 | 80 | V | 4 | ||
| PGD off voltage | 0 | 80 | V | 4 | |||
| Junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Input current, enabled | IIN-EN | 1.3 | 1.6 | mA | UVLO > 2.5 V and OVLO < 2.5 V | 5 | |
| Input current, disabled | IIN-DIS | 480 | 650 | µA | UVLO < 2.5 V or OVLO > 2.5 V | 5 | |
| Power-On reset threshold at VIN to trigger insertion timer | PORIT | 7.6 | 8 | V | VIN increasing | 5 | |
| Power-On reset threshold at VIN to enable all functions | POREN | 8.4 | 9 | V | VIN increasing | 5 | |
| OUT bias current, enabled | IOUT-EN | 11 | µA | OUT = VIN, Normal operation | 5 | ||
| OUT bias current, disabled | IOUT-DIS | 50 | µA | Disabled, OUT = 0 V, SENSE = VIN | 5 | ||
| UVLO threshold | UVLOTH | 2.45 | 2.5 | 2.55 | V | 5 | |
| UVLO hysteresis current | UVLOHYS | 12 | 21 | 30 | µA | UVLO = 1 V | 5 |
| UVLO delay to GATE high | UVLODEL | 55 | µs | Delay to GATE high | 5 | ||
| UVLO bias current | UVLOBIAS | 1 | µA | UVLO = 48 V | 5 | ||
| OVLO threshold | OVLOTH | 2.4 | 2.5 | 2.6 | V | 5 | |
| OVLO hysteresis current | OVLOHYS | 12 | 21 | 30 | µA | OVLO = 2.6 V | 5 |
| OVLO delay to GATE high | OVLODEL | 55 | µs | Delay to GATE high | 5 | ||
| OVLO bias current | OVLOBIAS | 1 | µA | OVLO = 2.4 V | 5 | ||
| Power limit sense voltage (VIN-SENSE) | PWRLIM-1 | 19 | 25 | 31 | mV | SENSE-OUT = 48 V, RPWR = 150 kΩ | 5 |
| Power limit sense voltage (VIN-SENSE), 24 V case | PWRLIM-2 | 25 | mV | SENSE-OUT = 24 V, RPWR = 75 kΩ | 5 | ||
| PWR pin current | IPWR | 20 | µA | VPWR = 2.5 V | 5 | ||
| GATE source current | IGATE | 10 | 16 | 22 | µA | Normal operation, GATE-OUT = 5 V | 5 |
| GATE sink current, UVLO low | IGATE | 1.75 | 2 | 2.6 | mA | UVLO < 2.5 V | 5 |
| GATE sink current, circuit breaker or UVLO/PORIT pulldown | IGATE | 45 | 110 | 175 | mA | VIN to SENSE = 150 mV or VIN < PORIT, VGATE = 5 V | 5 |
| Gate output voltage in normal operation | VGATE | 11.4 | 12 | 12.6 | V | GATE-OUT voltage | 5 |
| Current limit threshold voltage | VCL | 48.5 | 55 | 61.5 | mV | VIN-SENSE voltage | 6 |
| Current limit response time | tCL | 45 | µs | VIN-SENSE stepped from 0 mV to 80 mV | 6 | ||
| SENSE input current, enabled | ISENSE | 23 | µA | Enabled, SENSE = OUT | 6 | ||
| SENSE input current, disabled | ISENSE | 60 | µA | Disabled, OUT = 0 V | 6 | ||
| Circuit breaker threshold voltage | VCB | 80 | 105 | 130 | mV | VIN to SENSE | 6 |
| Circuit breaker response time | tCB | 0.44 | 1.2 | µs | VIN to SENSE stepped from 0 mV to 150 mV, time to GATE low, no load | 6 | |
| TIMER upper threshold | VTMRH | 3.76 | 4 | 4.16 | V | 6 | |
| TIMER lower threshold, restart cycles (LM5069-2) | VTMRL | 1.187 | 1.25 | 1.313 | V | Restart cycles (LM5069-2) | 6 |
| TIMER lower threshold, end of 8th cycle (LM5069-2) | VTMRL | 0.3 | V | End of 8th cycle (LM5069-2) | 6 | ||
| Re-enable threshold (LM5069-1) | VTMRL | 0.3 | V | Re-enable Threshold (LM5069-1) | 6 | ||
| Insertion time current | ITIMER | 3 | 5.5 | 8 | µA | 6 | |
| Sink current, end of insertion time | ITIMER | 1 | 1.5 | 2 | mA | TIMER pin = 2 V | 6 |
| Fault detection current | ITIMER | 51 | 85 | 120 | µA | 6 | |
| Fault sink current | ITIMER | 1.25 | 2.5 | 3.75 | µA | 6 | |
| Fault restart duty cycle | DCFAULT | 0.5 | % | LM5069-2 only | 6 | ||
| Fault to GATE low delay | tFAULT | 12 | µs | TIMER pin reaches 4 V | 6 | ||
| Power good threshold, decreasing (SENSE-OUT) | PGDTH | 0.67 | 1.25 | 1.85 | V | Decreasing | 6 |
| Power good threshold, increasing (SENSE-OUT) | PGDTH | 0.95 | 1.25 | 1.55 | V | Increasing, relative to decreasing threshold | 6 |
| PGD output low voltage | PGDVOL | 60 | 150 | mV | ISINK = 2 mA | 6 | |
| PGD off leakage current | PGDIOH | 5 | µA | VPGD = 80 V | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 156 | °C/W | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | Abs | (1) For detailed information on soldering plastic VSSOP packages, see Absolute Maximum Ratings for Soldering (SNOA549) available from | 4 |
CAD (KiCad official)
- Symbol:
LM5069MM-2 - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: VSSOP-10-0.5mm (KiCad packages3D, STEP)
- 3D model files:
lm5069mm-2-etched.step/lm5069mm-2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5069mm-2.step/lm5069mm-2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (39 pp, sha256
d60d8106a6e81139, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).