← Commit history

Initial commit: component/lm5039sqx

Ray ·b9f655a3dd ·
2 files changed +307
README.mdadded+61
@@ -0,0 +1,61 @@+# LM5039SQX++**Texas Instruments** · DC-DC Controllers · WQFN-24-EP(4x5)++LM5039SQX from Texas Instruments, in a WQFN-24-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | NC | unconnected | No electrical contact. |+| 2 | ACL | input | A capacitor connected between the ACL pin and GND operates as an integrator in the average current limit circuitry. |+| 3 | COMP | input | An external opto-coupler connected to the COMP pin sources current into an internal NPN current mirror to control PWM duty cycle. |+| 4 | RT | input | An external resistor connected between RT and AGND sets the internal oscillator frequency, normally regulated at 2V. |+| 5 | AGND | power_in | Analog Ground, connect directly to Power Ground. |+| 6 | CS | input | Current sense input driven by a signal representative of the primary current, with 600mV threshold for peak cycle-by-cycle limiting and 500mV threshold for average current limiting. |+| 7 | SS | input | An internal 110µA current source charges an external capacitor to set the soft-start rate. |+| 8 | DLY | input | An external resistor to ground sets the timing for the non-overlap time of HO to SR1 and LO to SR2. |+| 9 | RES | input | If the current limit is exceeded during any cycle, a 22µA current is sourced to the RES pin capacitor for hiccup mode restart control. |+| 10 | NC | unconnected | No electrical contact. |+| 11 | HB | power_in | Boost voltage for the HO driver; an external diode is required from VCC to HB and an external capacitor is required from HS to HB to power the gate driver. |+| 12 | HS | power_in | Switch node connection common to the transformer and both power switches, providing a return path for the HO gate driver. |+| 13 | HO | output | Output of the high side PWM gate driver, capable of sinking 2A peak current. |+| 14 | LO | output | Output of the low side PWM gate driver, capable of sinking 2A peak current. |+| 15 | PGND | power_in | Power Ground, connect directly to Analog Ground. |+| 16 | VCC | power_out | Output of the high voltage start-up regulator regulated to 7.6V. |+| 17 | SR2 | output | Synchronous rectifier driver output for control of the synchronous FET gate, capable of 0.5A peak current. |+| 18 | SR1 | output | Synchronous rectifier driver output for control of the synchronous FET gate, capable of 0.5A peak current. |+| 19 | REF | power_out | Output of 5V Reference with typical output current of 20mA, requiring local decoupling with a 0.1µF capacitor. |+| 20 | NC | unconnected | No electrical contact. |+| 21 | VIN | power_in | Input voltage source to the Start-up Regulator with operating input range of 13V to 100V with transient capability to 105V. |+| 22 | NC | unconnected | No electrical contact. |+| 23 | RAMP | input | Modulator ramp signal set by an external RC circuit from VIN, discharged at the conclusion of every cycle by an internal FET. |+| 24 | UVLO | input | Line Under-Voltage Lockout determined by an external voltage divider from the power source for shutdown and standby control. |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-24-EP(4x5) |+| Category | Power Supply Chip |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `LM5039SQX`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`+- 3D model: WQFN-24-EP(4x5) (KiCad packages3D, STEP)+- 3D model files: `lm5039sqx-etched.step` / `lm5039sqx-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5039sqx.step` / `lm5039sqx.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5039) (35 pp, sha256 `a662d4b1f77df0cf`, retrieved 2026-09-17, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm5039sqx-datasheet.pdf)
page.jsonadded+246
@@ -0,0 +1,246 @@+{+  "slug": "lm5039sqx",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Controllers, WQFN-24-EP(4x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "lm5039sqx",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm5039sqx.kicad_sym",+    "lm5039sqx.kicad_mod",+    "lm5039sqx.glb",+    "lm5039sqx.step",+    "lm5039sqx.lbr",+    "docs/hero.png",+    "docs/lm5039sqx-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM5039SQX",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-24-EP(4x5)",+    "pin_count": 25,+    "category": "Power Supply Chip",+    "subcategory": "DC-DC Controllers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm5039",+    "parts": {+      "symbol": "lm5039sqx.kicad_sym",+      "footprint": "lm5039sqx.kicad_mod",+      "model_3d": "lm5039sqx-etched.glb",+      "model_3d_plain": "lm5039sqx.glb",+      "model_3d_step": "lm5039sqx-etched.step",+      "model_3d_step_plain": "lm5039sqx.step",+      "lbr": "lm5039sqx.lbr"+    },+    "distributor_links": {+      "lcsc": "C2658642"+    },+    "pins": [+      {+        "number": "1",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical contact."+      },+      {+        "number": "2",+        "name": "ACL",+        "type": "input",+        "description": "A capacitor connected between the ACL pin and GND operates as an integrator in the average current limit circuitry."+      },+      {+        "number": "3",+        "name": "COMP",+        "type": "input",+        "description": "An external opto-coupler connected to the COMP pin sources current into an internal NPN current mirror to control PWM duty cycle."+      },+      {+        "number": "4",+        "name": "RT",+        "type": "input",+        "description": "An external resistor connected between RT and AGND sets the internal oscillator frequency, normally regulated at 2V."+      },+      {+        "number": "5",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog Ground, connect directly to Power Ground."+      },+      {+        "number": "6",+        "name": "CS",+        "type": "input",+        "description": "Current sense input driven by a signal representative of the primary current, with 600mV threshold for peak cycle-by-cycle limiting and 500mV threshold for average current limiting."+      },+      {+        "number": "7",+        "name": "SS",+        "type": "input",+        "description": "An internal 110µA current source charges an external capacitor to set the soft-start rate."+      },+      {+        "number": "8",+        "name": "DLY",+        "type": "input",+        "description": "An external resistor to ground sets the timing for the non-overlap time of HO to SR1 and LO to SR2."+      },+      {+        "number": "9",+        "name": "RES",+        "type": "input",+        "description": "If the current limit is exceeded during any cycle, a 22µA current is sourced to the RES pin capacitor for hiccup mode restart control."+      },+      {+        "number": "10",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical contact."+      },+      {+        "number": "11",+        "name": "HB",+        "type": "power_in",+        "description": "Boost voltage for the HO driver; an external diode is required from VCC to HB and an external capacitor is required from HS to HB to power the gate driver."+      },+      {+        "number": "12",+        "name": "HS",+        "type": "power_in",+        "description": "Switch node connection common to the transformer and both power switches, providing a return path for the HO gate driver."+      },+      {+        "number": "13",+        "name": "HO",+        "type": "output",+        "description": "Output of the high side PWM gate driver, capable of sinking 2A peak current."+      },+      {+        "number": "14",+        "name": "LO",+        "type": "output",+        "description": "Output of the low side PWM gate driver, capable of sinking 2A peak current."+      },+      {+        "number": "15",+        "name": "PGND",+        "type": "power_in",+        "description": "Power Ground, connect directly to Analog Ground."+      },+      {+        "number": "16",+        "name": "VCC",+        "type": "power_out",+        "description": "Output of the high voltage start-up regulator regulated to 7.6V."+      },+      {+        "number": "17",+        "name": "SR2",+        "type": "output",+        "description": "Synchronous rectifier driver output for control of the synchronous FET gate, capable of 0.5A peak current."+      },+      {+        "number": "18",+        "name": "SR1",+        "type": "output",+        "description": "Synchronous rectifier driver output for control of the synchronous FET gate, capable of 0.5A peak current."+      },+      {+        "number": "19",+        "name": "REF",+        "type": "power_out",+        "description": "Output of 5V Reference with typical output current of 20mA, requiring local decoupling with a 0.1µF capacitor."+      },+      {+        "number": "20",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical contact."+      },+      {+        "number": "21",+        "name": "VIN",+        "type": "power_in",+        "description": "Input voltage source to the Start-up Regulator with operating input range of 13V to 100V with transient capability to 105V."+      },+      {+        "number": "22",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical contact."+      },+      {+        "number": "23",+        "name": "RAMP",+        "type": "input",+        "description": "Modulator ramp signal set by an external RC circuit from VIN, discharged at the conclusion of every cycle by an internal FET."+      },+      {+        "number": "24",+        "name": "UVLO",+        "type": "input",+        "description": "Line Under-Voltage Lockout determined by an external voltage divider from the power source for shutdown and standby control."+      },+      {+        "number": "25",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 25 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 35,+        "cost_usd": 0.6587,+        "at": "2026-09-17T22:28:08"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm5039",+        "pages": 35,+        "sha256": "a662d4b1f77df0cf",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file