main
Ray
Publish 0.1.0
94655c0
LM5025MTCX
Texas Instruments · DC-DC Converters · TSSOP-16
LM5025MTCX from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input to start-up regulator, 13 V to 90 V with transient capability to 100 V. |
| 2 | RAMP | input | Modulator ramp signal; an external RC circuit from Vin sets the ramp slope and an internal FET discharges it at the end of every cycle. |
| 3 | CS1 | input | Current sense input for cycle-by-cycle limiting when CS1 exceeds 0.25 V, with 50 ns leading edge blanking after OUT_A switches high. |
| 4 | CS2 | input | Current sense input for soft restart; above 0.25 V the outputs are disabled and soft-start starts, with 50 ns leading edge blanking after OUT_A goes high. |
| 5 | TIME | input | Resistor RSET to GND gives in-phase OUT_A/OUT_B with overlap, and RSET to REF gives out-of-phase outputs with deadtime. |
| 6 | REF | power_out | Precision 5-V reference, maximum output current 10 mA, decouple locally with 0.1 µF; stays low until line UVLO and VCC UV comparators are satisfied. |
| 7 | VCC | power_out | Output of the internal high-voltage start-up regulator, regulated to 7.6 V; an auxiliary winding raising it above the setpoint shuts down the start-up regulator. |
| 8 | OUT_A | output | Main switch PWM output gate driver with 3-A peak sink current capability. |
| 9 | OUT_B | output | Active clamp switch gate driver capable of 1.25-A peak sink current. |
| 10 | PGND | power_in | Power ground, connect directly to analog ground. |
| 11 | AGND | power_in | Analog ground, connect directly to power ground. |
| 12 | SS | input | Soft-start control; an external capacitor and internal 20-µA current source set the ramp, reduced to 1 µA after a CS2 overcurrent or over-temperature event. |
| 13 | COMP | input | Input to the pulse width modulator with internal 5-kΩ pullup; an external opto-coupler sinks current to control PWM duty cycle. |
| 14 | RT | input | Oscillator timing resistor pin; an external resistor to ground sets the oscillator frequency. |
| 15 | SYNC | input | Oscillator UP and DOWN synchronization input; external clock must be 20% lower than the free-running frequency, with no maximum sync frequency constraint. |
| 16 | UVLO | input | Line undervoltage shutdown input with 2.5-V comparator threshold and hysteresis set by an internal 20-µA current source. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16 |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | VIN | -0.3 | 100 | V | 4 | ||
| VCC to GND | VCC | -0.3 | 16 | V | 4 | ||
| CS1, CS2 to GND | -0.3 | 1 | V | 4 | |||
| All other inputs to GND | -0.3 | 7 | V | 4 | |||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| VIN voltage | VIN | 13 | 90 | V | 4 | ||
| External voltage applied to VCC | VCC | 8 | 15 | V | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 98.7 | °C/W | PW (TSSOP) 16-pin | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 27.8 | °C/W | PW (TSSOP) 16-pin | 5 | ||
| Junction-to-board thermal resistance | RθJB | 44.3 | °C/W | PW (TSSOP) 16-pin | 5 | ||
| VCC regulation | VCC Reg | 7.3 | 7.6 | 7.9 | V | No load, TJ = -40°C to 125°C | 5 |
| VCC current limit | 20 | 25 | mA | TJ = -40°C to 125°C | 5 | ||
| Startup regulator leakage (external Vcc supply) | I-VIN | 165 | 500 | µA | VIN = 100 V, TJ = -40°C to 125°C | 5 | |
| Shutdown current (Iin) | Iin | 350 | 450 | µA | UVLO = 0 V, TJ = -40°C to 125°C | 5 | |
| VCC undervoltage hysteresis | 1 | 1.5 | 2 | V | TJ = -40°C to 125°C | 5 | |
| VCC supply current | ICC | 4.2 | mA | Cgate = 0, TJ = -40°C to 125°C | 5 | ||
| Ref voltage | VREF | 4.85 | 5 | 5.15 | V | IREF = 0 mA, TJ = -40°C to 125°C | 5 |
| Ref voltage regulation | 25 | 50 | mV | IREF = 0 to 10 mA, TJ = -40°C to 125°C | 5 | ||
| Ref current limit | 10 | 20 | mA | TJ = -40°C to 125°C | 5 | ||
| Cycle by cycle threshold voltage (CS1) | 0.22 | 0.25 | 0.28 | V | TJ = -40°C to 125°C | 5 | |
| Cycle skip threshold voltage (CS2) | 0.22 | 0.25 | 0.28 | V | TJ = -40°C to 125°C | 5 | |
| CS sink impedance (clocked) | 30 | 50 | Ω | ICS = 10 mA, TJ = -40°C to 125°C | 6 | ||
| Soft-start current source normal | 17 | 22 | 27 | µA | TJ = -40°C to 125°C | 6 | |
| Soft-start current source following a CS2 event | 0.5 | 1 | 1.5 | µA | TJ = -40°C to 125°C | 6 | |
| Frequency1 | 175 | 200 | 225 | kHz | TJ = -40°C to 125°C | 6 | |
| Frequency2 | 500 | 580 | 660 | kHz | RT = 10.4 KΩ, TJ = -40°C to 125°C | 6 | |
| Minimum sync pulse width | 100 | ns | TJ = -40°C to 125°C | 6 | |||
| Duty cycle | 0 | 80 | % | TJ = -40°C to 125°C | 6 | ||
| COMP to PWM offset | 0.7 | 1 | 1.3 | V | TJ = -40°C to 125°C | 6 | |
| COMP open circuit voltage | 4.3 | 5.9 | V | TJ = -40°C to 125°C | 6 | ||
| COMP short circuit current | 0.6 | 1 | 1.4 | mA | COMP = 0 V, TJ = -40°C to 125°C | 6 | |
| Ramp clamp level | 2.4 | 2.5 | 2.6 | V | Delta RAMP measured from onset of OUT_A to Ramp peak, COMP = 5 V, TJ = -40°C to 125°C | 6 | |
| Undervoltage shutdown threshold | 2.44 | 2.5 | 2.56 | V | TJ = -40°C to 125°C | 6 | |
| Undervoltage shutdown hysteresis | 16 | 20 | 24 | µA | TJ = -40°C to 125°C | 6 | |
| OUT_A high saturation | 5 | 10 | Ω | MOS device at Iout = -10 mA, TJ = -40°C to 125°C | 6 | ||
| OUT_A low saturation | 6 | 9 | Ω | MOS device at Iout = 10 mA, TJ = -40°C to 125°C | 6 | ||
| OUT_B high saturation | 10 | 20 | Ω | MOS device at Iout = -10 mA, TJ = -40°C to 125°C | 6 | ||
| OUT_B low saturation | 12 | 18 | Ω | MOS device at Iout = 10 mA, TJ = -40°C to 125°C | 6 | ||
| Overlap time | 75 | 105 | 135 | ns | RSET = 38 kΩ connected to GND, 50% to 50% transitions, TJ = -40°C to 125°C | 7 | |
| Deadtime | 75 | 105 | 135 | ns | RSET = 29.5 kΩ connected to REF, 50% to 50% transitions, TJ = -40°C to 125°C | 7 | |
| VCC undervoltage lockout voltage (positive going VCC) | 120 | 220 | mV | VCC Reg minus value, TJ = -40°C to 125°C (typ at TJ = 25°C) | 5 | ||
| Prop CS1 delay to output | 40 | ns | CS1 step from 0 to 0.4 V, Cgate = 0 | 5 | |||
| Prop CS2 delay to output | 50 | ns | CS2 step from 0 to 0.4 V, Cgate = 0 | 5 | |||
| Thermal shutdown threshold | TSD | 165 | °C | 7 |
CAD (KiCad official)
- Symbol:
LM5025MTCX - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
lm5025mtcx-etched.step/lm5025mtcx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5025mtcx.step/lm5025mtcx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (33 pp, sha256
c3b4c8949f53952b, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM5025MTCX
**Texas Instruments** · DC-DC Converters · TSSOP-16
LM5025MTCX from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input to start-up regulator, 13 V to 90 V with transient capability to 100 V. |
| 2 | RAMP | input | Modulator ramp signal; an external RC circuit from Vin sets the ramp slope and an internal FET discharges it at the end of every cycle. |
| 3 | CS1 | input | Current sense input for cycle-by-cycle limiting when CS1 exceeds 0.25 V, with 50 ns leading edge blanking after OUT_A switches high. |
| 4 | CS2 | input | Current sense input for soft restart; above 0.25 V the outputs are disabled and soft-start starts, with 50 ns leading edge blanking after OUT_A goes high. |
| 5 | TIME | input | Resistor RSET to GND gives in-phase OUT_A/OUT_B with overlap, and RSET to REF gives out-of-phase outputs with deadtime. |
| 6 | REF | power_out | Precision 5-V reference, maximum output current 10 mA, decouple locally with 0.1 µF; stays low until line UVLO and VCC UV comparators are satisfied. |
| 7 | VCC | power_out | Output of the internal high-voltage start-up regulator, regulated to 7.6 V; an auxiliary winding raising it above the setpoint shuts down the start-up regulator. |
| 8 | OUT_A | output | Main switch PWM output gate driver with 3-A peak sink current capability. |
| 9 | OUT_B | output | Active clamp switch gate driver capable of 1.25-A peak sink current. |
| 10 | PGND | power_in | Power ground, connect directly to analog ground. |
| 11 | AGND | power_in | Analog ground, connect directly to power ground. |
| 12 | SS | input | Soft-start control; an external capacitor and internal 20-µA current source set the ramp, reduced to 1 µA after a CS2 overcurrent or over-temperature event. |
| 13 | COMP | input | Input to the pulse width modulator with internal 5-kΩ pullup; an external opto-coupler sinks current to control PWM duty cycle. |
| 14 | RT | input | Oscillator timing resistor pin; an external resistor to ground sets the oscillator frequency. |
| 15 | SYNC | input | Oscillator UP and DOWN synchronization input; external clock must be 20% lower than the free-running frequency, with no maximum sync frequency constraint. |
| 16 | UVLO | input | Line undervoltage shutdown input with 2.5-V comparator threshold and hysteresis set by an internal 20-µA current source. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16 |
| Category | Power Supply Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | VIN | -0.3 | | 100 | V | | 4 |
| VCC to GND | VCC | -0.3 | | 16 | V | | 4 |
| CS1, CS2 to GND | | -0.3 | | 1 | V | | 4 |
| All other inputs to GND | | -0.3 | | 7 | V | | 4 |
| Junction temperature | TJ | | | 150 | °C | | 4 |
| Storage temperature | Tstg | -55 | | 150 | °C | | 4 |
| VIN voltage | VIN | 13 | | 90 | V | | 4 |
| External voltage applied to VCC | VCC | 8 | | 15 | V | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Junction-to-ambient thermal resistance | RθJA | | 98.7 | | °C/W | PW (TSSOP) 16-pin | 5 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 27.8 | | °C/W | PW (TSSOP) 16-pin | 5 |
| Junction-to-board thermal resistance | RθJB | | 44.3 | | °C/W | PW (TSSOP) 16-pin | 5 |
| VCC regulation | VCC Reg | 7.3 | 7.6 | 7.9 | V | No load, TJ = -40°C to 125°C | 5 |
| VCC current limit | | 20 | 25 | | mA | TJ = -40°C to 125°C | 5 |
| Startup regulator leakage (external Vcc supply) | I-VIN | | 165 | 500 | µA | VIN = 100 V, TJ = -40°C to 125°C | 5 |
| Shutdown current (Iin) | Iin | | 350 | 450 | µA | UVLO = 0 V, TJ = -40°C to 125°C | 5 |
| VCC undervoltage hysteresis | | 1 | 1.5 | 2 | V | TJ = -40°C to 125°C | 5 |
| VCC supply current | ICC | | | 4.2 | mA | Cgate = 0, TJ = -40°C to 125°C | 5 |
| Ref voltage | VREF | 4.85 | 5 | 5.15 | V | IREF = 0 mA, TJ = -40°C to 125°C | 5 |
| Ref voltage regulation | | | 25 | 50 | mV | IREF = 0 to 10 mA, TJ = -40°C to 125°C | 5 |
| Ref current limit | | 10 | 20 | | mA | TJ = -40°C to 125°C | 5 |
| Cycle by cycle threshold voltage (CS1) | | 0.22 | 0.25 | 0.28 | V | TJ = -40°C to 125°C | 5 |
| Cycle skip threshold voltage (CS2) | | 0.22 | 0.25 | 0.28 | V | TJ = -40°C to 125°C | 5 |
| CS sink impedance (clocked) | | | 30 | 50 | Ω | ICS = 10 mA, TJ = -40°C to 125°C | 6 |
| Soft-start current source normal | | 17 | 22 | 27 | µA | TJ = -40°C to 125°C | 6 |
| Soft-start current source following a CS2 event | | 0.5 | 1 | 1.5 | µA | TJ = -40°C to 125°C | 6 |
| Frequency1 | | 175 | 200 | 225 | kHz | TJ = -40°C to 125°C | 6 |
| Frequency2 | | 500 | 580 | 660 | kHz | RT = 10.4 KΩ, TJ = -40°C to 125°C | 6 |
| Minimum sync pulse width | | | | 100 | ns | TJ = -40°C to 125°C | 6 |
| Duty cycle | | 0 | | 80 | % | TJ = -40°C to 125°C | 6 |
| COMP to PWM offset | | 0.7 | 1 | 1.3 | V | TJ = -40°C to 125°C | 6 |
| COMP open circuit voltage | | 4.3 | | 5.9 | V | TJ = -40°C to 125°C | 6 |
| COMP short circuit current | | 0.6 | 1 | 1.4 | mA | COMP = 0 V, TJ = -40°C to 125°C | 6 |
| Ramp clamp level | | 2.4 | 2.5 | 2.6 | V | Delta RAMP measured from onset of OUT_A to Ramp peak, COMP = 5 V, TJ = -40°C to 125°C | 6 |
| Undervoltage shutdown threshold | | 2.44 | 2.5 | 2.56 | V | TJ = -40°C to 125°C | 6 |
| Undervoltage shutdown hysteresis | | 16 | 20 | 24 | µA | TJ = -40°C to 125°C | 6 |
| OUT_A high saturation | | | 5 | 10 | Ω | MOS device at Iout = -10 mA, TJ = -40°C to 125°C | 6 |
| OUT_A low saturation | | | 6 | 9 | Ω | MOS device at Iout = 10 mA, TJ = -40°C to 125°C | 6 |
| OUT_B high saturation | | | 10 | 20 | Ω | MOS device at Iout = -10 mA, TJ = -40°C to 125°C | 6 |
| OUT_B low saturation | | | 12 | 18 | Ω | MOS device at Iout = 10 mA, TJ = -40°C to 125°C | 6 |
| Overlap time | | 75 | 105 | 135 | ns | RSET = 38 kΩ connected to GND, 50% to 50% transitions, TJ = -40°C to 125°C | 7 |
| Deadtime | | 75 | 105 | 135 | ns | RSET = 29.5 kΩ connected to REF, 50% to 50% transitions, TJ = -40°C to 125°C | 7 |
| VCC undervoltage lockout voltage (positive going VCC) | | | 120 | 220 | mV | VCC Reg minus value, TJ = -40°C to 125°C (typ at TJ = 25°C) | 5 |
| Prop CS1 delay to output | | | 40 | | ns | CS1 step from 0 to 0.4 V, Cgate = 0 | 5 |
| Prop CS2 delay to output | | | 50 | | ns | CS2 step from 0 to 0.4 V, Cgate = 0 | 5 |
| Thermal shutdown threshold | TSD | | 165 | | °C | | 7 |
## CAD (KiCad official)
- Symbol: `LM5025MTCX`
- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`
- 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files: `lm5025mtcx-etched.step` / `lm5025mtcx-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5025mtcx.step` / `lm5025mtcx.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5025) (33 pp, sha256 `c3b4c8949f53952b`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm5025mtcx-datasheet.pdf)