main
Ray
lm43602pwp: specified limits as data (metadata.characteristics, 60 rows from the datasheet)
af67934
LM43602PWP
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
LM43602PWP from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor. |
| 2 | SW | output | Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor. |
| 3 | CBOOT | passive | Bootstrap capacitor connection for high-side driver; connect 470-nF capacitor from CBOOT to SW pin. |
| 4 | VCC | power_out | Internal bias supply output regulated at 3.2 V nominal; connect 2.2-10 µF bypass capacitor to AGND, never short or load this pin. |
| 5 | BIAS | power_in | Optional internal LDO supply input; tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V, external 3.3-5 V rail if available, or tie to ground when not in use. |
| 6 | SYNC | input | Clock input to synchronize switching action to external clock 200-2200 kHz; use high-speed termination to prevent ringing, ground if not used. |
| 7 | RT | passive | Connect resistor from this pin to AGND to program switching frequency 200-2200 kHz; leave floating for 500 kHz default. |
| 8 | PGOOD | output | Open-drain output for power-good flag; use 10-100 kΩ pull-up resistor to logic rail or DC voltage no higher than 12 V. |
| 9 | FB | input | Feedback sense input pin; connect to midpoint of feedback divider to set VOUT, do not short this pin to ground during operation. |
| 10 | AGND | power_in | Analog ground pin; ground reference for internal references and logic, connect to system ground. |
| 11 | SS/TRK | input | Soft-start control pin; leave floating for 4.1 ms internal soft-start ramp, or connect capacitor to extend or external voltage ramp for tracking. |
| 12 | EN | input | Enable input to internal LDO and regulator; high = ON, low = OFF; connect to VIN or external voltage source, do not float. |
| 13 | VIN | power_in | Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible. |
| 14 | VIN | power_in | Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible. |
| 15 | PGND | power_in | Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths. |
| 16 | PGND | power_in | Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths. |
| 17 | PAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to PGND (input voltage, absolute max) | -0.3 | 42 | V | At maximum duty cycle of 0.01% (note 2) | 4 | ||
| EN to PGND | -0.3 | V | Upper limit printed as VIN + 0.3 | 4 | |||
| FB, RT, SS/TRK to AGND | -0.3 | 3.6 | V | 4 | |||
| PGOOD to AGND | -0.3 | 15 | V | 4 | |||
| SYNC to AGND | -0.3 | 5.5 | V | 4 | |||
| BIAS to AGND | -0.3 | 30 | V | Printed as 30 or VIN, whichever is lower (note 3) | 4 | ||
| AGND to PGND | -0.3 | 0.3 | V | 4 | |||
| SW to PGND | -0.3 | V | Upper limit printed as VIN + 0.3 | 4 | |||
| SW to PGND less than 10-ns transients | -3.5 | 42 | V | 4 | |||
| CBOOT to SW | -0.3 | 5.5 | V | 4 | |||
| VCC to AGND | -0.3 | 3.6 | V | 4 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| VIN to PGND (input voltage, recommended) | 3.5 | 36 | V | 4 | |||
| EN | -0.3 | V | Upper limit printed as VIN | 4 | |||
| FB | -0.3 | 1.1 | V | 4 | |||
| PGOOD | -0.3 | 12 | V | 4 | |||
| BIAS input not used | -0.3 | 0.3 | V | 4 | |||
| BIAS input used | 3.3 | 28 | V | Printed as 28 or VIN (note 2) | 4 | ||
| AGND to PGND (recommended) | -0.1 | 0.1 | V | 4 | |||
| Output voltage | VOUT | 1 | 28 | V | 4 | ||
| Output current | IOUT | 0 | 2 | A | 4 | ||
| Operating junction temperature range | TJ | -40 | 125 | °C | 4 | ||
| Minimum input voltage for start-up | VIN-MIN-ST | 3.8 | V | 5 | |||
| Shutdown quiescent current | ISHDN | 1.2 | 3.1 | µA | VEN = 0 V | 5 | |
| Operating quiescent current (non-switching) from VIN | IQ-NONSW | 5 | 10 | µA | VEN = 3.3 V; VFB = 1.5 V; VBIAS = 3.4 V external | 5 | |
| Operating quiescent current (non-switching) from external VBIAS | IBIAS-NONSW | 85 | 130 | µA | VEN = 3.3 V; VFB = 1.5 V; VBIAS = 3.4 V external | 5 | |
| Voltage level to enable the internal LDO output VCC (precision enable high) | VEN-VOUT-H | 2 | 2.2 | 2.42 | V | VENABLE high level | 5 |
| Enable input leakage current | ILKG-EN | 0.85 | 1.75 | µA | VEN = 3.3 V | 5 | |
| Internal LDO input change-over threshold to BIAS (rising) | VBIAS-ON | 2.94 | 3.15 | V | VBIAS rising threshold | 5 | |
| Feedback voltage | VFB | 1.004 | 1.011 | 1.018 | V | TJ = 25ºC | 6 |
| Feedback voltage | VFB | 0.994 | 1.011 | 1.026 | V | TJ = –40ºC to 85ºC | 6 |
| Feedback voltage | VFB | 0.994 | 1.011 | 1.03 | V | TJ = –40ºC to 125ºC | 6 |
| Input leakage current at FB pin | ILKG-FB | 0.2 | 65 | nA | FB = 1 V | 6 | |
| Peak inductor current limit | IHS-LIMIT | 3.65 | 4.5 | 5.15 | A | 6 | |
| Inductor current valley limit | ILS-LIMIT | 1.75 | 2 | 2.25 | A | 6 | |
| Soft-start charge current | ISSC | 1.25 | 2 | 2.75 | µA | 6 | |
| Power-good flag overvoltage tripping threshold | VPGOOD-HIGH | 110 | 113 | % | % of FB voltage | 6 | |
| Power-good flag undervoltage tripping threshold | VPGOOD-LOW | 77 | 88 | % | % of FB voltage | 6 | |
| PGOOD pin pulldown resistance when power bad | RPGOOD | 69 | 150 | Ω | VEN = 3.3 V | 6 | |
| PGOOD pin pulldown resistance when power bad | RPGOOD | 150 | 350 | Ω | VEN = 0 V | 6 | |
| Minimum high side MOSFET ON-time | tON-MIN | 125 | 165 | ns | Specified by design (note 1) | 7 | |
| Minimum high side MOSFET OFF-time | tOFF-MIN | 200 | 250 | ns | Specified by design (note 1) | 7 | |
| Oscillator default frequency | FOSC-DEFAULT | 425 | 500 | 580 | kHz | RT pin open circuit | 7 |
| Minimum adjustable frequency | FADJ | 200 | kHz | With 1% resistors at RT pin | 7 | ||
| Maximum adjustable frequency | FADJ | 2200 | kHz | 7 | |||
| Frequency adjust accuracy | 10 | % | 7 | ||||
| Sync clock high level threshold | VSYNC-HIGH | 2 | V | 7 | |||
| Sync clock low level threshold | VSYNC-LOW | 0.4 | V | 7 | |||
| Sync clock maximum duty cycle | DSYNC-MAX | 90 | % | 7 | |||
| Sync clock minimum duty cycle | DSYNC-MIN | 10 | % | 7 | |||
| Minimum sync clock ON and OFF time | TSYNC-MIN | 80 | ns | 7 | |||
| Internal LDO output voltage VCC | VCC | 3.28 | V | VIN ≥ 3.8 V | 5 | ||
| Undervoltage lockout threshold for VCC (rising) | VCC-UVLO | 3.1 | V | VCC rising threshold | 5 | ||
| Shutdown threshold (thermal shutdown) | TSD | 160 | °C | Shutdown threshold (note 1, specified by design) | 5 | ||
| High-side MOSFET ON-resistance | RDS-ON-HS | 120 | mΩ | IOUT = 1 A; VBIAS = VOUT = 3.3 V | 6 | ||
| Low-side MOSFET ON-resistance | RDS-ON-LS | 65 | mΩ | IOUT = 1 A; VBIAS = VOUT = 3.3 V | 6 | ||
| Operating quiescent current (switching) | IQ-SW | 27 | µA | VEN = 3.3 V; IOUT = 0 A; RT = open; VBIAS = VOUT = 3.3 V; RFBT = 1.0 Meg | 5 | ||
| Junction-to-ambient thermal resistance (HTSSOP) | RθJA | 38.9 | °C/W | HTSSOP (16 pins); simulated on 4-layer JEDEC board; see Figure 64 for copper area (note 3) | 5 | ||
| Junction-to-case (bottom) thermal resistance (HTSSOP) | RθJC(bot) | 1.7 | °C/W | HTSSOP (16 pins); simulated on 4-layer JEDEC board | 5 |
CAD (KiCad official)
- Symbol:
LM43602PWP - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm43602pwp-etched.step/lm43602pwp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm43602pwp.step/lm43602pwp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (52 pp, sha256
7057c203046aa5b7, retrieved 2026-09-27, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM43602PWP
**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP
LM43602PWP from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor. |
| 2 | SW | output | Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor. |
| 3 | CBOOT | passive | Bootstrap capacitor connection for high-side driver; connect 470-nF capacitor from CBOOT to SW pin. |
| 4 | VCC | power_out | Internal bias supply output regulated at 3.2 V nominal; connect 2.2-10 µF bypass capacitor to AGND, never short or load this pin. |
| 5 | BIAS | power_in | Optional internal LDO supply input; tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V, external 3.3-5 V rail if available, or tie to ground when not in use. |
| 6 | SYNC | input | Clock input to synchronize switching action to external clock 200-2200 kHz; use high-speed termination to prevent ringing, ground if not used. |
| 7 | RT | passive | Connect resistor from this pin to AGND to program switching frequency 200-2200 kHz; leave floating for 500 kHz default. |
| 8 | PGOOD | output | Open-drain output for power-good flag; use 10-100 kΩ pull-up resistor to logic rail or DC voltage no higher than 12 V. |
| 9 | FB | input | Feedback sense input pin; connect to midpoint of feedback divider to set VOUT, do not short this pin to ground during operation. |
| 10 | AGND | power_in | Analog ground pin; ground reference for internal references and logic, connect to system ground. |
| 11 | SS/TRK | input | Soft-start control pin; leave floating for 4.1 ms internal soft-start ramp, or connect capacitor to extend or external voltage ramp for tracking. |
| 12 | EN | input | Enable input to internal LDO and regulator; high = ON, low = OFF; connect to VIN or external voltage source, do not float. |
| 13 | VIN | power_in | Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible. |
| 14 | VIN | power_in | Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible. |
| 15 | PGND | power_in | Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths. |
| 16 | PGND | power_in | Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths. |
| 17 | PAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Management (PMIC) |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to PGND (input voltage, absolute max) | | -0.3 | | 42 | V | At maximum duty cycle of 0.01% (note 2) | 4 |
| EN to PGND | | -0.3 | | | V | Upper limit printed as VIN + 0.3 | 4 |
| FB, RT, SS/TRK to AGND | | -0.3 | | 3.6 | V | | 4 |
| PGOOD to AGND | | -0.3 | | 15 | V | | 4 |
| SYNC to AGND | | -0.3 | | 5.5 | V | | 4 |
| BIAS to AGND | | -0.3 | | 30 | V | Printed as 30 or VIN, whichever is lower (note 3) | 4 |
| AGND to PGND | | -0.3 | | 0.3 | V | | 4 |
| SW to PGND | | -0.3 | | | V | Upper limit printed as VIN + 0.3 | 4 |
| SW to PGND less than 10-ns transients | | -3.5 | | 42 | V | | 4 |
| CBOOT to SW | | -0.3 | | 5.5 | V | | 4 |
| VCC to AGND | | -0.3 | | 3.6 | V | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| VIN to PGND (input voltage, recommended) | | 3.5 | | 36 | V | | 4 |
| EN | | -0.3 | | | V | Upper limit printed as VIN | 4 |
| FB | | -0.3 | | 1.1 | V | | 4 |
| PGOOD | | -0.3 | | 12 | V | | 4 |
| BIAS input not used | | -0.3 | | 0.3 | V | | 4 |
| BIAS input used | | 3.3 | | 28 | V | Printed as 28 or VIN (note 2) | 4 |
| AGND to PGND (recommended) | | -0.1 | | 0.1 | V | | 4 |
| Output voltage | VOUT | 1 | | 28 | V | | 4 |
| Output current | IOUT | 0 | | 2 | A | | 4 |
| Operating junction temperature range | TJ | -40 | | 125 | °C | | 4 |
| Minimum input voltage for start-up | VIN-MIN-ST | | | 3.8 | V | | 5 |
| Shutdown quiescent current | ISHDN | | 1.2 | 3.1 | µA | VEN = 0 V | 5 |
| Operating quiescent current (non-switching) from VIN | IQ-NONSW | | 5 | 10 | µA | VEN = 3.3 V; VFB = 1.5 V; VBIAS = 3.4 V external | 5 |
| Operating quiescent current (non-switching) from external VBIAS | IBIAS-NONSW | | 85 | 130 | µA | VEN = 3.3 V; VFB = 1.5 V; VBIAS = 3.4 V external | 5 |
| Voltage level to enable the internal LDO output VCC (precision enable high) | VEN-VOUT-H | 2 | 2.2 | 2.42 | V | VENABLE high level | 5 |
| Enable input leakage current | ILKG-EN | | 0.85 | 1.75 | µA | VEN = 3.3 V | 5 |
| Internal LDO input change-over threshold to BIAS (rising) | VBIAS-ON | 2.94 | | 3.15 | V | VBIAS rising threshold | 5 |
| Feedback voltage | VFB | 1.004 | 1.011 | 1.018 | V | TJ = 25ºC | 6 |
| Feedback voltage | VFB | 0.994 | 1.011 | 1.026 | V | TJ = –40ºC to 85ºC | 6 |
| Feedback voltage | VFB | 0.994 | 1.011 | 1.03 | V | TJ = –40ºC to 125ºC | 6 |
| Input leakage current at FB pin | ILKG-FB | | 0.2 | 65 | nA | FB = 1 V | 6 |
| Peak inductor current limit | IHS-LIMIT | 3.65 | 4.5 | 5.15 | A | | 6 |
| Inductor current valley limit | ILS-LIMIT | 1.75 | 2 | 2.25 | A | | 6 |
| Soft-start charge current | ISSC | 1.25 | 2 | 2.75 | µA | | 6 |
| Power-good flag overvoltage tripping threshold | VPGOOD-HIGH | 110 | | 113 | % | % of FB voltage | 6 |
| Power-good flag undervoltage tripping threshold | VPGOOD-LOW | 77 | | 88 | % | % of FB voltage | 6 |
| PGOOD pin pulldown resistance when power bad | RPGOOD | | 69 | 150 | Ω | VEN = 3.3 V | 6 |
| PGOOD pin pulldown resistance when power bad | RPGOOD | | 150 | 350 | Ω | VEN = 0 V | 6 |
| Minimum high side MOSFET ON-time | tON-MIN | | 125 | 165 | ns | Specified by design (note 1) | 7 |
| Minimum high side MOSFET OFF-time | tOFF-MIN | | 200 | 250 | ns | Specified by design (note 1) | 7 |
| Oscillator default frequency | FOSC-DEFAULT | 425 | 500 | 580 | kHz | RT pin open circuit | 7 |
| Minimum adjustable frequency | FADJ | 200 | | | kHz | With 1% resistors at RT pin | 7 |
| Maximum adjustable frequency | FADJ | | | 2200 | kHz | | 7 |
| Frequency adjust accuracy | | | | 10 | % | | 7 |
| Sync clock high level threshold | VSYNC-HIGH | 2 | | | V | | 7 |
| Sync clock low level threshold | VSYNC-LOW | | | 0.4 | V | | 7 |
| Sync clock maximum duty cycle | DSYNC-MAX | | | 90 | % | | 7 |
| Sync clock minimum duty cycle | DSYNC-MIN | 10 | | | % | | 7 |
| Minimum sync clock ON and OFF time | TSYNC-MIN | 80 | | | ns | | 7 |
| Internal LDO output voltage VCC | VCC | | 3.28 | | V | VIN ≥ 3.8 V | 5 |
| Undervoltage lockout threshold for VCC (rising) | VCC-UVLO | | 3.1 | | V | VCC rising threshold | 5 |
| Shutdown threshold (thermal shutdown) | TSD | | 160 | | °C | Shutdown threshold (note 1, specified by design) | 5 |
| High-side MOSFET ON-resistance | RDS-ON-HS | | 120 | | mΩ | IOUT = 1 A; VBIAS = VOUT = 3.3 V | 6 |
| Low-side MOSFET ON-resistance | RDS-ON-LS | | 65 | | mΩ | IOUT = 1 A; VBIAS = VOUT = 3.3 V | 6 |
| Operating quiescent current (switching) | IQ-SW | | 27 | | µA | VEN = 3.3 V; IOUT = 0 A; RT = open; VBIAS = VOUT = 3.3 V; RFBT = 1.0 Meg | 5 |
| Junction-to-ambient thermal resistance (HTSSOP) | RθJA | | 38.9 | | °C/W | HTSSOP (16 pins); simulated on 4-layer JEDEC board; see Figure 64 for copper area (note 3) | 5 |
| Junction-to-case (bottom) thermal resistance (HTSSOP) | RθJC(bot) | | 1.7 | | °C/W | HTSSOP (16 pins); simulated on 4-layer JEDEC board | 5 |
## CAD (KiCad official)
- Symbol: `LM43602PWP`
- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`
- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `lm43602pwp-etched.step` / `lm43602pwp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm43602pwp.step` / `lm43602pwp.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm43602) (52 pp, sha256 `7057c203046aa5b7`, retrieved 2026-09-27, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm43602pwp-datasheet.pdf)